Jump to content
SAU Community

Recommended Posts

Time to move on, so here it is :

I've had this car for 5-6 years, the previous owner spent well over 50k on this build just before moving over seas and me purchasing it, and I've put ten of thousands into it since then..

engine was built by Nisspeed in Adelaide and now has 35k kms on it. Runs 600rwhp on 98 @ 1.8bar

HKS step2 2.8 stroker, full counter crank and rods kit, CP pistons.
Brand new head from Nissan, Jun 272 in and ex cams, 10.8mm(?) lift, special retainers and all the jazz needed to support the cams and high revs, heads extensively ported.
Big dollar hypertune plenum and single throttle body setup
Custom alloy breather tank etc
Jun oil pump, N1 water pump,

ATI balancer

Trust sump extension.
Garrett TO4Z turbo and big Turbonetics external gate
OS Giken 2 way front diff
OS Giken cross mission 5spd gearset with input shaft 800+hp rated, and Billet centre plate, Less than 5000kms old
Nismo Super Coppermix spec C twin plate, less than 5oookms old, gearbox, clutch and rear diff just cost $10k plus
Nismo GT pro 1.5 rear diff less than 5000kms old
wastegate plumbed back into HKS 4inch exhaust
Huge alloy PWR radiator,

disgustingly thick Trust Spec R intercooler 160mm
Fuel system to cater for 1000hp+, in boot setup as in pics, new fuelab 1500hp variable speed pump, all E85 compatible
1000cc HKS injectors,
HKS fuel rail 11mm

Teflon braided fuel lines
splitfire coilpacks
Motec M800 ECU + Loom + Sensors

HKS coilovers
V-Spec Brembo's rear, K-Sport 8-pot 356mm fronts with new rotors
Midnight purple paint in excellent condition. Will try and get some pictures with better light to show off the purple.
Excellent condition original interior with almost no wear in the usual places (seat bolsters, etc)

Custom Air/con system, to fit with big intercooler, radiator and oil cooler

Fullrace ETS pro Attessa computer. Complete stand alone unit that enables you to control the 4wd from 0-50/50 split and RWD mode.

Series 3 Zenons
Silly money spent NO EXPENSE SPARED ON THIS BUILD. $38k ono

Richard 0411861466 WA

post-48287-0-51161200-1411891955_thumb.jpg

post-48287-0-80569200-1411892029_thumb.jpg

post-48287-0-45769700-1411892076_thumb.jpg

post-48287-0-18106200-1411892140_thumb.jpg

post-48287-0-46169900-1411892180_thumb.jpg

post-48287-0-88822400-1411892242_thumb.jpg

post-48287-0-01830500-1411892687_thumb.jpg
post-48287-0-13585100-1411892846_thumb.jpg

Edited by tricstar
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/449131-midnight-purple-r33-gtr-28l-600rwhp/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...

Guy got a bargain. Would've liked a bit more. But we're only talking a few grand. Sorta glad it's done, now I can concentrate on other things.

Got a GTSt that I'm striping out for a track car, so I'm not gone.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I did a skidpan night at SMSP this week, it was much cheaper than $350. But yeah, you need to slap an LSD in that thing.  I put an OS Giken in the 370Z and it's f**king MARVELOUS even compared to Nissan's viscous LSD. So you're saying it's free now that it's a housing estate? 😂
    • Nah, the car seems to run exactly as it did prior, in saying this it does "seem" to be better down low, like more eager to rev, but that may be 100% placebo effect from intake noise But, I'm not worried about it at all, in the end it is a fairly low compression NA engine that has a well shrouded intake,  if it is getting hotter IAT I cannot notice anything negative performance wise from the seat of my pants thrashing it about on the street or sitting in traffic, so meh, car now now makes induction noise so I'm happy
    • Do you have an IAT sensor? It's worth checking it to see. You may be suprised how little gap you actually need to flood your engine with hot air. (I tape up my airbox for a reason) :p
    • @KinkstaahKrinkle paint the "silver" alloy, not the red filter frame Engine bay heat won't be a issue worth worrying about as the silver alloy blocks it off on 3 sides, as for the top, the bonnet seals most of it and the big OEM CAI intake snorkel is still fitted in its original position  I will head into Clark's Rubber when I have some time to grab some pinch weld to tidy up the alloy after I paint it As for performance, I honestly wasn't expecting any, the only reason I got it is because the intake noise sounds cool to my old ears when I'm feeding it the beans Sometimes it's the silly things you do in in life that gives the most fun, and I do love anything that makes cool car noises In other news: I survived 4 nights at sea with Jackie not throwing me over board, holidays are continuing now as we are currently chilling at the Beachcomber in Toukley, after taking the coast roads from Sydney in the MX5, top down all the way, Toukley is where I spent a good deal of my youth holidaying during the summer months, there's lots of reminiscing going on,  and lots of beaches and old houses to visit Next on the list is to head to Batemans Bay for a few days, but we will take the Commodore out to stretch its legs, then Commodore hasn't really moved for months
    • There’s probably people who’d like to do it and then when it comes to putting their hands in their pockets they’ll all disappear into the shadows 
×
×
  • Create New...