DAN-33

Figured as much, explains why the car had a Boost tee in box of parts. Installed that and got it on 7psi. more then happy now

No worries, hopefully i can find something. local stores dont stock much

Need a single one, will buy 5 if i have too. PM me and i send $

Went to do this and realised i dont have the Boost controller. i have a line from Actuator to the pipe, and then a blocked off pipe from the BOV return. If i ground the wire at the Plug, will it still tell the ECU to go 7psi? at the moment im getting 5psi most of time, higher up in range, it might hit 7psi now and then. ideas?

Ahhk Cheers Johnny, Once its out, can it be cleaned? fixed? or is it a chuck out and replace item? Just wanna know before i pull it out.

Yeah stock BOV mate, it makes a noise why replace it? haha Yeah i may just get some vacuum line and replace what i can anyway. How do i go about getting the AAC off from under the plenum? not much room to work around.

Hey, can you PM some more details on this? might be something i can try.

This has to be THE best and easiest explanation to installing a catch can EVER on a RB engine. Thank you!

Still hard to start in morning, i have to attempt to start it 4-5 times, then a little pedal work to get it to actually start. then it will hover at 500rpm for 2-3 seconds, then cold valve kicks in and bam, 1800rpm for warm up. Idle is perfect now,

Thank you, appreciate the Help, Good Forum, keep it up !!

Ahh nasty, thats what im hoping doesnt happen. Im going to clean up the bolts with a wire wheel and the treads in turbo too. better safe then sorry. Use loctite on them? this is my first dump pipe removal ever

Cheers, ill drench them night before and again on the day.

Got a dump pipe and hi flow cat on there way to match my 3" catback setup. Any tips on removing the stock stuff? ive heard the bolts can snap, Guessing just soak them twice a day for a few days before doing it or or maybe get the engine warm and crack them while warm, then undo fully when cold? For a R33 btw Also, whats the torque spec for when i re tighten them?

Kidding right? The light is already on due to HICAS removal... is the light going to change colour or get brighter when a fault happens else where?

Just wondering if anyone selling off a 3" dump pipe and front piece and a Hi-flow cat to suit a R33? I got a 3" catback already, but stock from turbo to cat In Tassy, can pay shipping if reasonable. Dan

or pull the globe out from Dash?

i understand mate, i know how it works, but all cars adjust different. some have pins, some are fixed ect. just wanted to know what im up for and if i need any "specialty" tools so i can grab them during week nothen worse then half in and Wahhmm, you need rarar and its sunday and shops that sell rarar's are closed

Sorry for not "actually looked under there" , just figured id get a heads up on what im dealing with before i go f^^k it. Not afraid to spin a spanner mate, just rather be prepared Seems my weekend is set, Camber arms, tyres, brakes, clutch, radiator and alarm setup

Ahhk, Any advice on that, havnt actually looked under there yet.

I got same issue, sorta. ive got a inch of "clutch" if that. it grabs as soon as it leaves the floor. Tried bleeding, following the guides on here. may give it another shot when i doing brake pads on weekend

Recently got a R33, Clutch pedal feels, odd??. like the first 2/3 of travel is soft then its rather hard. noticed its hard to get into 1st some times, if you rev out 2nd sometime it wont engage 3rd unless the pedal is near mashed into floor. Ive tried bleeding the system, new fluid. the middle box thingy is by passed. i followed guides on here, no air in it... pretty certain anyway. Didnt change the feel, if anything worse now. bad MC or slave? Any other ideas? i dont really want to pull box to find its Aok. Btw clutch doesnt seem to slip, or shudder. Friend of mine said it feels like a cracked pressure plate. the little prong bits in middle. had a similar issue with his 33.

Need a stock radiator for a R33. Anyone have one laying around in good nick?

All parts been bought, thank you,

Drivers side window motor windscreen washer bottle drivers side plastic trim that got between the rear quarter window and door window on outside. ignition barrel, door locks, boot lock and all keys. In Tas, will pay shipping.

http://www.skylinesaustralia.com/forums/topic/110431-diy-aac-valve-cleaning-idle-reset/