the_tonkau

Thanks boys! Leakdown down test next, then igniter module(its a series one). It has a new fuel filter and monitired fuel pressure on dyno OK. No rubber hose left on turbo inlet to crush. Probably look at the injectors next. Hey SK, when you used this fuel setup as an alternative to getting bigger injectors, could you get a nice smoooth idle? Some times (only first tune) it can be OK then it gets a bit grumpy/rough. Dripping/dirty injectors?.........will keep you updated guys. Thanks for the input, Stevo

Ash-It should fit straight on but I can't be sure. It fitted on mine no probs. BoostJunky- Still for sale

No leak down test as yet (maybe don't want to know the results!!) but its an original low KLM's motor so you would hope it has some more legs left. Any other different scenarios to try lads, I am open for idea's. The winner gets a slab! Cheers Stevo

Ash- I'm pretty sure the stock dump pipe is not 3 inches, its cast iron and restrictive as hell! The exhaust from the turbo to the cat can be one piece like mine or it can come in two pieces. Its sounds like you still have the crusty cast "dump" pipe which lives directly on the back of the exhaust housing on the turbo but have a larger "front pipe" which continues to the back of the cat. My pipe incorporates both these pipes. Do some searching on this site under dump or front pipe if my explanation is confusing. HPC coating is expensive but its the shit to have! Raza- as stated in the heading this is HPC or "Ceramic Coated" steel and not stainless steel. Stainless is good as it resists rust and looks good but HPC coated steel does the same as stainless as well as it keeps the heat inside the pipe to ensure better gas flow and stops the heat radiating outside the pipe thus keeping under bonnet temps down and lowers the chances of pipes/hoses melting when mounted near the exhaust.

BUMP!

SK - AHA!! I HOPED YOU WOULD DROP IN, IT'S GOT 7'S WITH .8MM GAP. PREVIOUS TO THESE COPPERS WE TRIED IRIDIUMS ETC AT MANY GAPS AND HEAT RANGES WITH NO LUCK. JTECH- ITS GOT A POWER FC SO NO BOOST/FUEL CUT ISSUES I KNOW THIS SYMPTOM HAS BEEN COVERED TO DEATH BUT I THINK MY PARTICULAR PROB COULD BE AN ODD ONE.......MMMMMMMM

Have had this problem since I got the car and it was stock as a rock and its still the same after all these mod's !!! The engine misses with any more than 12psi boost. This week all the following gear went in- t3/t4, FMIC,PFC,Adj Fuel Reg,Big Fuel pump,z32 afm,new plugs(copper-correct gap) and we tested every coil pack with a known good item. STILL MISSING. It runs like a dream until we go over 12psi. I have been told it could be the crank angle sensor(dry solder joints??) but we ran out of dyno time and crank angle sensors. I hope I have given enough details for some of the SA GURU's to offer some idea's. Cheers Stevo

In EC, one year old and ready for a new home. Bolts directly onto the back of the turbo and goes to the front of your cat. Comes with oxy sensor mounting and bracket to suit a R33 Gtst so it bolts straight on!! Due to LARGE numbers of dreamers last time I sold parts here there are some new rules. NO OFFERS, NO WANKERS, NO COD. NO ,YOU CAN'T PAY IT OFF. NO haggle SPECIAL price........ $250...cost me $595 From UAS First to put the money in my hand gets it! [email protected] goto UAS web site for pics www.uniqueautosports.com

Eriktufa, Its a Whistler 1745, goto www.whistlergroup.com for complete details and pics! [email protected].

Hippy, read this website for info! www.whistlergroup.com Mick, Decisions decisions, unfortunately it has to go and like I said, first in best dressed. Wish I could zap it up to you today but driving half way to ballarat to sell something for a $200 loss(orig cost $399) does not get me too excited. THE SALE CONTINUES.... [email protected] .au.

If you know what your after and what features this model has, why dont I just send it to you? DD or cash my Acc and I will send it today!

hawthorn Work northcote Home Its close to sale, first to pay gets it!

Hi Eriktufa, Are you chasing a r33 or r34 standard IC? I have a r33 for $100 in EC

IF YOU WELD TOGETHER 3 OF THEM SIDE BY SIDE, YOU COULD CREATE AN EXCELLENT AND GRIPPY STEP! :bahaha:

Is it the same as a R33 Gtst IC? I have one that has just been reco'ed and is mint! $150 Steve 0411403081

Take it to court! You can prove there is %10 tolerance in your speedo, thats 6 kays! Dont be bullied man, stand and fight the revenue raising mungrels! So do you want it?

Back on the market....again! [email protected]

Cheers mate! If anyone does look around they will quickly work out that the stuff is VERY cheap. I'm not looking at making a million dollars just want to turn the stuff over and cover some costs for all the new stuff I am fittting. It gets a bit annoying when some people offer stupid amounts and/or pull out after saying yes (twice already) Thanks again Mase:D Steve

No, I have upgraded and dont need it!

If its mounted correctly it is works great. Yes, it picks up LASER, from the front and the rear. It tells you in a voice what has targeted you! As well as saving money and demerit points its sounds way cool!! I have been made an offer but the first to pay $200(cost be $450) gets it!

Buyer dropped out, back on sale!! [email protected]

Some parts still available!! contact [email protected] :uh-huh:

I already have another offer of $375 so the first one to $400 gets it! Good luck

I have a HPC coated 3" UAS supplied dump/front pipe, comes with oxy sensor mount and all brackets...its the shit! Bought it for $695 12 months ago, sell $450 [email protected]

How much Ben? [email protected]