flavzz

Does anyone have a custom c34 stagea sub enclosure you want to sell? Located in Adelaide

I need one of these. Noting the age of the post and the OP may no longer be online but does anyone have one they want to sell? Im in Adelaide.

Just need one of these to replace a lost one to suit 18 inch LMGT4. Does anyone have one lying around? Cheers

Engine Stock internals RB26 Turbos Garrett GT2860R-7s, 15.5 psi (currently boost is limited due to 7psi actuators) Intake Apexi power intake kit (twin pods) Twin turbo pipe mod (plate welded into the TT pipe) to separate air to front and rear turbo to promote laminar flow and reduce turbulence Stock intake pipework with AFMs inactive (O2 controlled by Link Wideband) Exhaust HPI stainless dump pipes HPI stainless equal length front pipes Apexi N1 3.5 inch stainless cat back Stock cast exhaust manifolds, metal multilayer gasket, new genuine Nissan studs and nuts Fuel System 1000cc Bosch Dynamic Flow Matched Injectors Walbro 460lph Fuel Pump inc wiring upgrade direct to battery Turbosmart FPR800 Fuel Pressure Regulator Ignition System Stock Ignitor Splitfire Coil Packs BCPR7ES plugs gapped to 0.7 ECU and Sensors Link G4X ECU CAN Wideband O2 Link Flex Fuel Sensor Syltech fuel pressure sensor Syltech oil temperature and pressure sensor Syltech coolant temp sensor Syltech air temp sensor 3 port MAC valve (electronic boost control via the ECU) Tune Dyno tuned for full flex 262kW on 98 282kW on E85 Was told by the tuner that I was limited by the small actuators (7psi) meaning they could only get 15.5psi with the boost controller, I have some HKS 14psi actuators incoming and will run it up again on 18-20psi.

Thanks for this mate. I'll have a chat with the tuner about this option.

I'm getting prepared to tune my 260rs with the following main components. Nistune ECU on E85 with flex, Garrett -7 turbos, Walbro 460 fuel pump etc injectors to be chosen by the tuner I've got most bases covered apart from air flow metres as I'm still running the stock ones. The traditional go to was Z32s or Nismo AFMs but are there any other modern cost effective options out there that work with the Nistune ECU?

Does anyone have one of these for sale to fit 33/34 gtr and 260RS? I'm interested in buying one in Adelaide or happy to pay for postage for it to get here. Cheers

Hi All, I'm currently upgrading my 260rs to -7 turbos and looking to find some quality dump pipes, either Mines/HPI/Midori with the large bellmouth design. Also looking for Mines equal length front pipes, either the old 60mm inlets and 70mm outlet or the newer 70mm inlets and 80mm outlet. Located in Adelaide but will pay for postage for the right item. Cheers

Big thanks to Ehnto for sending me the boost controller. Legend.

Anyone have one they're not using? Can't seem to find them online anymore.

Did you have any luck finding one? I'm in the same situation as you. It appears these guys have vanished.

Sold!

Genuine Nissan remanufactured ECU for R32 GTR. I bought this a few years ago with the intention of chipping it with a nistune board however I recently found another ecu so this is surplus to my needs. I have tested it in my 260rs and it works great. $150. Can pickup in Adelaide or post anywhere in Australia

Apexi N1 stainless steel catback exhaust built for R32 GTR but has had one section added to fit my 260rs Stagea. 3 inch exhaust in good condition but sits a little low for my liking. A few minor scrapes. Rear cannon in great condition, always polished. Would suit 260rs or 32/33 GTR with minor modifications. May suit other stageas with some modification. $350 pickup in southern suburbs of Adelaide. Price negotiable for a quick sale.

Nice one. I'll look into this. Cheers!

Hoping to get a bracket from one of the previous group buys to use for a track day coming up. Can pick up in Melbourne or Adelaide. Cheers

Fire extinguisher bracket to suit stagea 260rs. Ideally one of the group buy from previous would be great. Can pick up in Vic or SA. Cheers

Awesome. Thanks for sharing.

Really well run event and excellent venue guys, we had a great day as spectators. Keen to get out there for the next one if possible

Great result mate, very clean looking 260. Any plans to take it to the track/strip?

Excellent. Should be a great day

How many cars entered for this so far?

Definitely keen to check out some RB powered machines around PI. I'll get the 260 out there one day.

Hey all, I'm chasing some stock 260rs wheels. Ideally located in Adelaide but if the price is right I would consider shipping them from interstate. Cheers

Will do, cheers