burnfest

My r33 wouldnt idle with maps from 2 other cars, I got lucky with the 3rd. I have a wolf 3d with MAP sensor. Like you I just wanted to get the car running, then drive it to get tuned and not get ripped off. I think the problem is that all the base timing, tps open and shut values, etc must get programmed in from your car. Aftermarket computers cant adapt like a stocker ecu can. Dont know if this helps... Alex.

Wanted: 1.5 or 2way centre for r33. I want the shafts also if the stock ones dont fit. Under $1000 PM me, Cheers.

How did you get it to that carpark when you can't drive it? Wouldn't the photos be from the compliance place or your house? Its strange that there is now no way of identifying the car, stolen or not.

bump

bump

If the sale falls thru, pm me ill take it. Alex.

Depends who you know I guess. Couldn't be more than $100 - 200. Still works out cheap for an as-new centre. I have the part numbers from the Nissan FAST program. 38435-N3210 PLATE-SPRING 38432-N9001 PLATE-FRICTION 38433-N9000 DISK-FRICTION You need four of each. When you put it together it goes: 2 spring plates on the outside, then a friction plate, then the 2 friction disks, and then the other friction plate. Same for the other side. Alex.

Selling a nismo gt (not gt pro like on the box) 2 way lsd centre. I was ripped on ebay by rougepi, I paid over $800 for this and the friction disks are missing. It uses the same parts as a gtr lsd, so you can get them from nissan or any place that rebuilds lsds. fits any r200 diff with the right shafts. I want $500 plus post. C.O.D. is fine. Im located in Bunbury WA. Alex.

Could you post some photos, were was it highflowed? Cheers.

pm'd you.

How much did the highflowing cost? what was the power rating?

Hey did you get my pm?

Do you have the the black plastic guards above the driver side front wheel? both pieces. [email protected] Alex.

If you can send it via COD to WA I will take it. Can pay a deposit if needed. Thanks, Alex.

Hey, after a mechanical diff centre for my r33 gtst. Secondhand in good condition is fine. 1.5 way wanted, will consider a 2 way if the price is right. PM me or reply here. Thanks, Alex.

I have also have one I got secondhand. Was the air temp sensor included with the wolf? and did you have to tell the wolf what pins you connected it up to? All I got was a big tuning booklet and no infomation about installation etc. Nice guide.

Does any one have the part number for the thrust bearing on a r33 gtst with a push type clutch. Is it the same size as a vl turbo one? I'm installing a new clutch and I want to replace the bearing as well. Thanks, Alex.

Hey I'm after a wastegate actuator from a rb20 turbo. PM me or post here if you have one laying around. Thanks, Alex.

After the black plastic guards around the drivers front wheel. Theres two pieces. How much?

updated firmware? i guess.

Yeah I'm still interested. Though it does seem to be dragging on a little, not having a go at you btw. Also it sounds like the design has changed alot since the first idea, and I would be alot more comfortable seeing the prototype before payment. Alex.

Do these whistle when driving? because my hybrid copy does and its bloody annoying. Very interested in one if they dont whistle. Alex.

I have a few skyline parts for sale on ebay the stock dump from my r33 http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...item=4544900051 The stock air-box intake scoop http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...item=4544901150 New pacemaker branded 3 inch front pipe for 32 or 33 http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...item=4544904616 The stock r33 intercooler and piping. http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...item=4544902620 Thanks, Alex.

interested in stealth wing, postage to w.a ?

is postage to WA going to be costly?