Jump to content
SAU Community

DazWah

Contributor
 View Profile  See their activity

  • Posts

    94

  • Joined

  • Last visited

  • Feedback

    100%

 Content Type 

Everything posted by DazWah

  1. DazWah
    Does anyone know if the G-Reddy Billit GTR r33 pulleys fit onto a rb25??
  2. DazWah
    they just have to be the same Wattage as original. Resistance = Volts² / Watts
  3. DazWah
    thank you so much! Your engine looks hot as! I will take some photos of mine when im done.
  4. DazWah
    Im wanting to get some Stainless Braided hose for my catch can. The size is 5/8 (16mm), has anyone else done this? Can you help me source the parts I require? Any help is appreciated.
  5. DazWah
    can i have a better picture, off full side of car please.
  6. DazWah
    Where can i get good priced body kits in Melbourne? I am after an r33 Trust front bar. UAS is way to expensive, most bars are around $750! Websites are also appreciated.
  7. DazWah
    ive never had a problem with stalling with blocked of bov. Try resetting your ecu, then drive it around a bit.
  8. DazWah
    Has anyone tried the just jap G4 suspension on a R33? I Still havent decided whether to get coilovers or the bilstein & whiteline package. Any suggestions?
  9. DazWah
    http://www.dashboardcentre.com.au/
  10. DazWah
    these look a bit better http://cgi.ebay.com.au/R32-R33-R34-RB25DET...1QQcmdZViewItem
  11. DazWah
    Hi i have just installed an adjustable rising rate fuel pressure regulator and was wondering what idle pressure should it be at?
  12. DazWah
    Hi changed my exhaust and the temp sensor was rusted and impossible to remove, does any one have a part number and where i can get a replacement sensor from? thanks
  13. DazWah
    put a higher diff ratio, from memory r33 gtst are 4.3's i assume the r34s are the same. By putting a higher diff ratio engine should rev quicker.
  14. DazWah
    wats the min psi setting for the actuator?
  15. DazWah
    it would work as long as the gas is flowing counter to the air intake for best result. As someone else said earlier it would require alot of gas! But you could probably make a section of the intercooler pipe refrigerated using the standard a/c setup and copper pipe. Please if yyou decide to do this ask a refrigeration mechanic to do so, all refrigerants are harmful to the ozone!
  16. DazWah
    do 17's still look good?
  17. DazWah
    I wanna buy some new rims, what size should i get 18's or 17's?
  18. DazWah
    what is the clutch model number?
  19. DazWah
    to get the sound you need a metal intake pipe instead of the plastic one with no air filter, also move the afm to somewhere on the cold side of the cooler, also block off BOV. That should do to get the sound of vl's.
  20. DazWah
    ok thanks, also another question has anyone changed the fittings on the rocker covers? instead of blocking the top of the t-piece can i replace it with an elbow? if so where did you get the fittings from.
  21. DazWah
    Ive just installed a catch can (think i done it right :S) anyway i used heater hose from supercheap for the lines all i need to know would they be ok or will the oil corrode the rubber?
  22. DazWah
    thanks all its a series 2 , 3 wires on afm and no silver box thingy.
  23. DazWah
    yes rb25, i got the hks one i want to change it because of the stock 10psi instead of 5psi
  24. DazWah
    is it under the cover? or at the back near firewall?
  25. DazWah
    hi can someone please help me with instructions to change the actuator? thank you.
×
×
  • Create New...