Jump to content
SAU Community

YangLIU

Members
 View Profile  See their activity

  • Posts

    386

  • Joined

  • Last visited

  • Feedback

    0%

 Content Type 

Everything posted by YangLIU

  1. YangLIU
    Hi gents, I got problem that my car often will shudder when i speed up to 110km/h and continue shudder if I acc to higher speed. I can feel the vibration from the seat, not from the steering wheel, i think it is rear wheel problem? currently my car has 4 brand new rotors, 4 brand new rims with balanced and 4 good tyres (about 10000km). anyone has idea or experience on this?
  2. YangLIU
    all sorted, 650rpm at idle without headlight and 850-900rpm at idle with headlight thanks mate!
  3. YangLIU
    yup, will try again today later
  4. YangLIU
    did 3 times with counting loudly....bad luck....LOL
  5. YangLIU
    hi gents, just cleaned throttle body and idle rev is 1100prm now in P position. and it is 950rpm in D positon. i followed throttle relearn instruction without CONSULT-II, but I can't turn on MIL. could anybody do me a favor that help to reset throttle in Sydney? cheers
  6. YangLIU
    Hi there, I have held on eBay with KOYO this morning and went to the seller's store of Golpher. Unfortunately it is close today. Will try to get Golpher one next Monday.
  7. YangLIU
    just ordered PIN one from ebay for my 2003 M35 auto. i am not aware there are 2 types of rad. what's your model?
  8. YangLIU
    i will try unplug it once and give you feedback. cheers.
  9. YangLIU
    yeah, it is same as what i am thinking. btw, will stock boost sensor impact EBC working if still plug stock boost sensor?
  10. YangLIU
    yeah sure. thanks mate. so your EBC also has boost sensor, right? if so, did you remove the stock boost sensor?
  11. YangLIU
    i know what you are talking about. actually Greddy EBC has 2 part for installation. 1 for solenoid, 1 for pressure signal reading. my original question is for pressure signal reading part. and your pic is for solenoid part. here is a part of Greddy EBC installation manual. I think M35 should use METHOD2 as below and it is same as your pic, right?
  12. YangLIU
    yup. thats what i am thinking. actually it is hard to use fuel reg line due to the narrow area. i already have a new boost gauge using stock boost gauge vacuum. now i consider to use BOV vacuum for EBC pressure reading.
  13. YangLIU
    thanks mate. i think i could get you. in your pic, you just changed solenoid only? For Greddy boost controller, the control unit need another vacuum pipe connect between manifold and fuel pressure regulator to measure the boost. and another question, shall i need to remove the stock boost sensor?
  14. YangLIU
    no worries. i am also not at home now.
  15. YangLIU
    yes sure. post your pic pls.
  16. YangLIU
    cool! thanks mate.
  17. YangLIU
    i think i could get you. actually this is for monitor the boost in manifold? and i could also connect this vacuum with boost gauge vacuum together?
  18. YangLIU
    thanks mate, you mean the left vacuum in red colour?
  19. YangLIU
    Hi everyone, just want to install Greddy Profec boost controller on my M35. here is some installation information: actually i am not sure which is fuel pressure regulator that need to connect to boost controller. i took a picture and marked 2 pipes in red and green. could anyone told me which is correct pipe connect to fuel pressure regulator? thanks all.
  20. YangLIU
    PM sent, mate
  21. YangLIU
    Hi Scotty, you are in MEL, right? I am in Sydney. I think it is hard to swap with you. would you like sell it? PM me pls. which colour is it? do you have pic?
  22. YangLIU
    I was on the way to castle hill exhaust
  23. YangLIU
    Is that you who talked to me in a holden? I went to fit nismo muffler at castle hill.
  24. YangLIU
    i would like to swap with stock bumper then.....really don't like current one.
  25. YangLIU
    thanks mate. I just don't want COPS pay more attention on my car....
×
×
  • Create New...