YangLIU

Yes, thin fan between Fmic and ac tho.

Hi all, I just fitted HDI Fmic with thin fan. Fan is working, but after drive for a while, water temp will go high. Any idea for that??

hot weather hot toys

AFM?

sold

pm sent $30 + $19.45 standard postage

Dolphin front strut bar for M35 http://page21.auctions.yahoo.co.jp/jp/auction/j371284041

finally my rear wing fly to Aus today. fitting easily, gain 100hp

just fitted factory rear wing. selling original M35 rear center/third brake light bar great working condition $30 Sydney local pickup or buyer expense to ship

sold

still available. it is not negotiable due to RRP is 9800yen.

Blitz Intercooler CS Kit - Nissan Stagea NM35 - Free Australia-Wide Delivery! $599 http://www.ebay.com.au/itm/Blitz-Intercooler-CS-Kit-Nissan-Stagea-NM35-Free-Australia-Wide-Delivery-/371330678487?hash=item5675087ed7:g:M00AAOSwAYtWGz62 Blitz Intercooler Se Kit - Nissan Stagea NM35 - Free Australia-wide Delivery! $599 http://www.ebay.com.au/itm/Blitz-Intercooler-Se-Kit-Nissan-Stagea-NM35-Free-Australia-wide-Delivery-/111674727604?hash=item1a00551cb4:g:XkQAAOSwl8NVWrze sold by Just Jap btw, 3.5% cashback on ebay fairly enough, i got 1 SE kit.

firstly i blocked the stcock boost sensor to bypass 21psi limitation (even though i only run 18psi) 2ndly, yeah, it is good options to get patch loom to avoid wiring mistake, or at least i could sell the whole emanage setup easily. for EMU, are there many H/W versions or can pick any EMU in market? i am going to grab one from JP directly. also for the EMU sensors, i know there are many sensors for EMU. do you know which sensor i should go for EMU working with our m35? thanks

PM sent.

i have stock map sensor on the car but blocked the vacuum. anyway, will get tune soon. btw, is it necessary to get emanage ultimate or just need emanage blue? also is there any plug and play loom or just need universal loom? so many questions.

besides throttle controller, is there any help if i remove EBC and swap back factory boost solenoid? you mentioned "Changing the max AFM output voltage on my EMU fixes it all the time" for my problem, when i got fuel cut, it was under low boost and i assume my stock AFM didn't get 5v voltage at that time. why changing max AFM output voltage could fix this problem?

yes yes and yes.

i am thinking how stock ecu get rid of this with stock turbo

btw, do you have throttle controller? how did you sort the problem? thanks.

ok, will try once and feedback here

Yes, I have throttle controller in my car

i haven't tune my car yet. maybe it is time to got FMIC and emanage

stagea m35, just one turbo. how to check if it is turbo shuffle?

hi all, i just went to Wollongong from Sydney today. on the highway with up hill,20-25% flatting on acc pedal, car speed around 100km/s - 110km/s, i always get fuel cut when injector load at 25%-30% (4-5psi on boost), when the issue came, injector load down to 0% then back to normal, sometimes injector load will up to 40%-50% then down to 10% then back to normal. (i got this info from greddy informeter touch). engine will not stall, just got one second fuel cut then back to normal and continue speed up. when i keep rev up with 20%-25% flatting on acc pedal, after the car got fuel cut and restore back, it will happens again after several seconds. i need to release my right foot then depress again to speed up again. i just did the main maintenance, change all oil/fluids, new plugs, transgo kits, hiflowed turbo (with EBC runs 17psi), turbosmart kompact, kn oil filter, new fuel filter, constant 12v on stock fuel pump (just blew the walbro pump), 4 new tyres (same size) for about 10000kms (actually there is no shudder when driving on flat highway over 100km/s or brake) there is no problem if the road is flat or 10% flatting on acc pedal (absolutely it is going slow down when on up hill road). after back home, i scanned with consult3, there is no error code. i am not quite sure when i have this problem but i just found it today, LOL. (there is no much up hill highway in Sydney...) may be the problem is stock fuel pump doesn't contact 12v? any ideas? or time to get emanage?

you can get speed signal from pin27 of TCU. it works well for my Blitz powermeter ID. cruise install instructions.pdf