my94coupe

Hi Guys, as the name suggests, I am looking for a stock front bar for a 1994 Series 1 R33 GTST Coupe please. I do not care about the color. I am in the Macedon Ranges, but i am happy to pick up to most places. Cheers Guys, Thanks, Jeff

hi mate, i had the same thing a while back, i got a set from Nizbits, the guys amazing, he can lay his hands on almost anything! quick google search should find his details, hes spot on.

SORTED< MODS PLEASE DELETE

Hi Guys, I am looking for a straight, rust free and undamaged bonnet for a 1994 R33 GTS-t Series 1 Coupe. I am not too worried about colour, as its going to paint anyway, Black would be awesome, but any colour would be fine, I am located in Gisborne, I am happy to pick it up or put up a little extra for fuel if you can deliver it. If you could please let me know your location and price please either here or PM that would be appreciated. Thanks Jeff

Hey you lot. So a month or two down the track, turns out there were two issues, not one. The IAC/AAC was the issue with the low speed stalling. Turns out the mechanic did FA when it came to the resto on it. I took it off my self as suggested above and sure as sh1te nothing had been done at all, he had simply replaced the gasket. An hour or so later and a bucket load of carbie cleaner sorted out the low rpm stalling. But, it did not address the other issues, so now it will hesitate, jerk hard, stutter then it will simply lose all electrical power for a few seconds, then stall. This can happen at speeds between 40-110km/hr, and it is getting very dangerous. No warning lights appear on the dash at all (i.e the engine warning light) until it stalls, then all the dash lights come on as it would if i turned the key one past acc. After pulling off to the side, i need to then switch the engine all the way off, count to five, then it will fire instantly. One of two things will then happen, either it will fire up and continue without issue, or, immediately repeat itself 5, 6, 7 times until it "clears" and I can get home. Further to note, it can be either at cruising or under acceleration, but not as i slow. So I am still chasing bugs. What i have done so far: cleaned the throttle body, cleaned the AFM sensor CRC'd every electrical connector i could find, checked every coil pack, checked every spark plug cleaned my K&N pod with recommended cleaner, But still it persists, Any guidance would be well received! Any suggestions or similar experiences? Cheers guys,

Hey, Any chance the OP could reinsert the photos for this post? I am still chasing issues with mine and looking for all the assistance i can get. Thanks Cheers

Hey Mate, For sure, i have attached photos taken tonight, Cheers

I'll do that, thanks Hadouken,

G'Day Mate, The idle all good, it was a little high when i got it back from the workshop, but has settled down now. Should i look for something in relation to that? I had been tempted a couple of times to remove it and check, i have a spare gasket, and given that the gasket is new, it maybe safe to remove and inspect. But like i said, i am non-mechanical. By your comment of "very easy to check AAC. As in super easy" inspires me to maybe give it a go. Thanks mate,

Hi Ben, The instructions given to the workshop were to remove, clean and replace the IAC with the new gasket. The new gasket is clearly visible and i was assured that the valved was cleaned....without removing it, i am guessing there is no way to check the work. I hadn't thought of the AFM sensor, i will chase that up, much appreciated, thank you. The blow off valve is factory standard, did you mean after fitting an aftermarket one? or with aged stock ones? Thanks for the reply mate, Cheers,

Hey Guys, I am more or a reader than a poster but i have come seeking advice. I have what i believe to be, is a substantial vacuum leak in my 1994 S1 R33 Gts-t RB25det 4 spd Auto, I say believe because at the moment, i am struggling to locate the problem, Being of a non-mechanical background, i can only say that believe i have a substantial vacuum leak, because all the indications point to that at this stage such as: - low rpm stalling, (4spd auto) - stall at idle, - stall when braking at slow speeds etc when the engine is at operating temperature. - I have to switch the engine compeletely off, count to five and it will fire again no issues - a softer brake pedal My initial research lead me to the IAA/IAC valve at the back of the stock intake manifold so i had it looked at, and a new gasket fitted, but the problem remains, now even more significantly since they worked on it. The little coupe has become undriveable. Can anyone shed some light on this? Has anyone had similar experiances? I have had my coupe for 15 years and never had an issue, this is the first time it ever given me grief. If it is Vacuum, then i guess it is replace every associated gasket and hose on the left side of the engine until it is located? Modifications to consider: Cold air induction FMIC. Other that than that the Engine is utterly stock. Attached are the most recent photos of my twin cam, merely for reference, however note that the blow-by hoses 2 and 3 and now NisGen parts. Cheers Guys, Regards Jeff

Hey Chris, Good to meet you, Mate, may i ask where you ordered these from? Do you have part numbers at all? Cheers