AlexCim

As far as i know, yes, it will fit for you. There is one guy that is using an R33 kit. Though, dont go ahead and cut a hole in the chassis too quickly, its easy to get a defect. Do what humble will do and use the kit/cooler etc, but get one pipe made custom to go under and then up to the cooler, like my pipes

Front bar reinforcement Probably R33 GTST Radiator support assembly R34 GTT i beleive. Stagea looks more R34 then R33 in the enginebay Radiator (auto) Huh? R33 Skyline rad fits Fan Blades R33 Skyline AFAIK Fan Clutch R33 Skyline AFAIK RH front steering tie rod Nissan for not too much (there was a thread...probably skyline) RH front steering tie rod end Nissan for not too much (there was a thread...probably skyline) W/screen washer motor Probably R33 Skyline Auto trans rubber hose Bursons, new. Get a tranny cooler in GB? LH rear upper control arms x2 R33 GTST LH rear lower control arms x2 R33 GTST Rims

Done and done, nearly there. Will place the order tomorrow arvo.

You fill the tranny through the dipstick tube. I just pissed oil overwhere. Removed the hoe here and there and tried to get all i could. First i drained the sump though. Also, i didnt jack my car up as i didnt want it on an angle to drain the oil. I got a funnel and some hose, put them together, and stuck the hose in the dipstick tube. That is my dodgy assed method.

System takes about 2L in total, 2.1L or so with the cooler. Closing tomorrow, Group buy on tranny coolers http://www.skylinesaustralia.com/forums/in...howtopic=105610 Thanks

I wouldnt mind a little one like that. Ive seen them on eBay before too. Any more in stock anywhere?

dont r34 gtt's come with dual tip mufflers that have flaps in them? when cold, the muffler is only 1 tip open, as it warms up etc, both tips open. This could do what you are talking about. For a fact, i know S2 manual stageas have these.

I really wouldnt say that. Depends what type of person you are. Ive spend 2k on my full exhaust, 1.2k on frount mount, id spend 2k on an ecu including tune etc etc (PFC), 1500 on a rebuilt turbo+install. Its not that bad! Sure you can do this chinese exhaust, chinese turbo, chinese frount mount, chinese ecu (exist? iono, probably some copy somewhere) + chinese mechanic/chinese tune (nothing against, just part of the theme) and get it for heaps less, but it depends where your priorities lie my friend. Id pay the above prices. I am not much of a hybrid/xforce fan (speaking from past experiances)

lol darrin, is that you Item location: Geelong, Victoria Australia Your from Geelong arnt you?

i really couldnt care less get some airhorns from supercheap for 25$ if you want loud

Ive paid my cash, ETA?

each side of the graph is the scale for either line. So its 10psi boost (lower line) Why the hell do they do dyno graphs with speed, should be RPM dammit

Well, that was prep work included by the person doing it for me, however, If i did the prep work myself it should shave some $$'s off it for me. Prep work is what you really pay for when it comes to painting a car...the paint itself if its a general colour isnt that expensive.

around 3-4k probably. Got to remove most of the engine related things

its not THAT much car, but for a decent job from my mate, i would expect to pay around 2000 mates rates no including engine bay, more for engine bay

been using the K104's for about 1000km now, they are great very good around corners, only a bit of understeer on fast and hard corners and my car is quite heavy. Wet they are great, cant loose traction.

RB26 conv http://www.skylinesaustralia.com/forums/in...howtopic=106465 Nismo Key http://www.skylinesaustralia.com/forums/in...howtopic=105382 Why not to manual convert/Manual conv info http://www.skylinesaustralia.com/forums/in...howtopic=105947 Piggy backs http://www.skylinesaustralia.com/forums/in...howtopic=105859 Insurance http://www.skylinesaustralia.com/forums/in...showtopic=68072 Glossary of terms http://www.skylinesaustralia.com/forums/in...howtopic=105692

Saw that, friend was interested but it was snapped up quite quickly. Nice car, good price, good value! Do you guys have children that can get Stageas?

I can get a bonnet made for stageas, but i need a stagea bonnet to get the ball rolling. I cant donate mine and i dont think people would be willing to pay for them Honestly, there is too much weight in this car to bother.

Id personally go black, but thats just me. Go bayside blue

Cant wait to get my DAYZ front bar... i need more flow An Autech would be nice, but I am thinking that with 200awkw the car should be more then plenty for the steert and i can get an autech in a few years when they come down a little bit more..

Just trying to get some more people on board before it closes, this is really a good cheap/effective upgrade. My old tranny cooler, after some normal driving i couldnt touch, it would burn my hand. This new one, I can touch it and its hot to the touch, but doesnt burn. THATS JUST NORMAL DRIVING. dont want to think what it gets like when i give it some stick around some corners! So yeh, upgrade is well worth it...

Stock bonnet will be around 25-30kg CF/FG bonnet will be around 12kg

This groupbuy is closing this wednesday, so if you are 100% put your name down. For all you auto drivers, this is a pretty good/needed product

A note to everyone, the group buy WILL be closing this wednesday, so put your names down now if you are 100% interested.