malialipali
-
Posts
66 -
Joined
-
Last visited
-
Feedback
0%
Content Type
Profiles
Forums
Events
Gallery
Media Demo
Store
Everything posted by malialipali
-
@nathan_LEM096 @FordAustralia Dont let them scam you in any way. They owe you every cent you spent.
-
any ideas on what this button does stagea 300rx
malialipali replied to darksould43's topic in Four Door Family & Wagoneers
I bought a little runabout colt few months ago. Had the same button adhered to the dash. Was wired up to led "tubes" all up under the dash. Have a look where the wiring is going - could be anything really -
Hi Sorry for not seeing this sooner. you can just use regular RCA cables or solder up your own from ends ( i did that cause I needed to put the car together that morning so I went to bunnings at the crack of dawn) As you need a lo output from the stereo to drive the amp. All you need to do is. Buy 2x RCA cables. Cut in half and trim to size. You need 5 in total. 4X for the speakers and 1x Sub The plugs go into the back of the stereo and the wire ends get pinned or soldered to the corresponding speaker wire on the harness. https://aerpro.com/app0120 For the sub output you will need to run a signal wire all the way back to the amp under the trim on the right hand side in the boot. You will also need to run a trigger wire from your deck to the amp. My deck has been in and unchanged near 2.5 years and has worked perfectly. Let me know if I can help further.
-
As a brand in freefall it seems @holden_aus has taken to suing customers for daring to speak out after being sold… https://t.co/SSvVax2HOJ
-
The HID bulbs will be fine, Ive got 6000k and they are great. Highbeams dont go HID they aren't fast enough, 6000K halogens you may struggle , best is probably 4500k.
-
The AC controls are integrated with the factory HU , you need the fascia kit with the buttons so your climate works. Is yours the Bose system? This is the kit I bought years ago, it fits (mostly) the top centre screw can be tricky and the buttons are slightly different look/feel. (once it ages it looks part of the car , the colour is very close) https://www.amazon.com/Metra-99-7604-Installation-2003-2004-Infiniti/dp/B000VYK90Q Grab a wiring harness http://www.supercheapauto.com.au/Product/Aerpro-Wiring-Harness-APP0120-to-suit-Nissan-1995-on/224825 And antenna adaptor https://www.autobarn.com.au/aerpro-nissan-d-diversity-lead-ap348a Underseat sub ---- umm might be tight measure it up and have a look at sizes online. I wired in a new deck with the low outputs straight to the factory amps and spare wheel sub. Has been more than adequate for my listening.
-
@CaltexAustralia @Shell_Australia @BP_Australia so are you guys saying that your 91/95RON fuels are dirty? Only you… https://t.co/YDPOJphTmL
-
@TurnbullMalcolm Holy Shit Mal, you realise that there is more to the world than the gun toting Yanks! And didn't w… https://t.co/0lecxg5yRy
-
I'm now fully convinced that @newscomauHQ is nothing more than a dirty dirty tabloid. And a 2nd rate one too.
-
What Have You Done To Your Stagea Lately?
malialipali replied to Hanso's topic in Four Door Family & Wagoneers
Just pressed in a new bearing for the AC idler pulley. Statewide sold me a 6301zz for 5 bucks cause they had em on shelf but not in the POS. . No more howling AC huzzah! -
Hi All, Just a quick sanity check if I'm diagnosing this right. Speedo needle appears to be working as normal up until 90 km/h above that it gets "stuck" at 100 km/h even though I'm accelerating , it will then jump and get stuck at 110km/h. Accelerating past 110 ( on a private road) it will be stuck on 110 and then jump to indicate the right speed. Slowing down the needle once again gets stuck at 110 , 100 and 90. Below 90 it functions normal. Once and only once , with the shifter in manual mode it did not react to gear changes. Turning the car off and back on after 10 seconds and everything went back to normal. The trans shifting feels weird at times, seems to coincide with the erratic needle. It will hold on to a gear far longer or far shorter than normal. I think the speed sender on the trans is toast? Or am I barking up the wrong tree. I did open the cluster 12+ months ago to fix a broken pcb trace. Cluster has worked fine since , the needle started being erratic about 6 weeks ago and is progressively getting worse. From my searches the speed sender/transducer is P/N 32707-AA100 same thing as a D40 navara, N16 pulsar, R32 skyline. Which seems to be $200+ here in Aus, and $15USD + delivery from anywhere else. Has anyone had to replace theirs? Is that the right part number? EDIT: No check-engine light or warnings at all from the car. No stored codes either. Thank you all .
-
Using https://www.onlinedoctranslator.com/ I translated EI.pdf , sample below. Obviously it does not translate the diagrams and there is Engrish but it helps! Google translate murders the document layout so I found it useless.
-
What Have You Done To Your Stagea Lately?
malialipali replied to Hanso's topic in Four Door Family & Wagoneers
Rear springs and shocks done, front underbody brace bolted up. Its now a totally different car. Why did I not do this sooner ??. Drivers rear shock was completely buggered. Could squeeze it down between my hands and it took upwards of 3 min for it to extend. I set my heights on the bench. Will let it settle for a week and then set again. Just need to buy some C spanners , anyone know where I can buy some in Perth? Of course all this effort has brought my attention to another clunk. Passenger side tie rod has play. So now need to find a set before I go get new shoes and an alignment. Suspension sorted now set my sights for go mods:) -
Got some V35/350 endlinks and lower control arm front bushes ( where the shocker fork bolts) Bought by mistake for my M35. Brand is Febest. Factory type replacements. $40 posted anywhere in AU for the lot. Located in Perth if someone wants to pickup. PM me
-
What Have You Done To Your Stagea Lately?
malialipali replied to Hanso's topic in Four Door Family & Wagoneers
So last weekend I did the lower arm bushes , radius rod bushes, sway bar bushes, lower ball joints and the AFM . My press groaned on some of the bushes. Those things are in there very very tight. The ball joints are a prick! Ride improved but it also highlighted just how bad my shocks/springs are. Midday today picked up a set of nearly new Tein GT Wagons and a R33 boot brace to make up a front under body brace. Fitted the fronts gonna do the rears tomorrow morning, got late for the rattle gun to be going. Took it for a quick spin around the block , holly crap the difference is incredible. My IT monkey hands are hurting and im cut up but it passes the shoe test. -
Ok all jokes aside.@TurnbullMalcolm are you and the @LiberalAus party seriously hell bent on ruining Australia's e… https://t.co/PEtkU7QZwt
-
am I missing something here @Telstra? you want me to move from 100Mbps cable to 15Mbps "NBN" cable then add a "spee… https://t.co/BSbv0x5MNB
-
@Scottludlam Not only is he an infant. But our own incompetent PM keeps giving him bigger rattles.
-
what's a couple thousand workers when you make over 6 billion in profit hey @NAB .............
-
@TurnbullMalcolm This gonna be a screw up like the NBN ? Will I get power via rechargeable batteries delivered by the shambles auspost is?
-
wait @commbank you can't be this stupid https://t.co/vIKZyTIrSc can you? You are offshoring cybersec! Your customers should be very worried!
