duz10s
Members-
Posts
94 -
Joined
-
Last visited
-
Feedback
0%
Content Type
Profiles
Forums
Events
Gallery
Media Demo
Store
Everything posted by duz10s
-
Hi All, Looking to purchase a 200sx s14 ASAP. Just looking for a clean preferably stock s14, preference for series 2, jungle green, auto or manual doesn't matter. WIll consider all options thou. Doesn't need to be a show car just a nice clean good example in good condition. Must be registered with clean title is a must. Cash ready to go, pm me with anything you have
-
Its actually got the 8285 on it, use to have the 7675 which is made 1170hp at the wheels when it was manual and 1000hp when it was auto.
-
Hi All, Chasing a set of front door trims for an r33 gtr, preferably series 1 or 2, must be in good condition with no rips etc Thanks
-
Hi All, Trying to locate a pinout diagram for the R33 GTR Attesa system, I can find the R32 one easily which shows the plugs and pinouts but really struggling to find the R33 GTR one. Any help or pointers would be great, main 2 wires/pins I'm trying to find out the TPS and the RPM input.
-
Morning, not sure if this was covered I cant find it mentioned anywhere however on a R33 GTR, the subframe has all this bracing that attaches to the body etc, I cannot get to the tie rod to undo at the HICAS without removing this bracing, however I am concerned the whole rear subframe will drop??? Can anyone help.
-
Hi just seeing if anyone has a set of good condition HKS cam gears Only after complete set. Thanks
-
I have 15 inch buddy clubs with 275/50/15 Street R's I am going to try some 3mm or 5mm spacers to see if I can get 275/60/15 profile on Not sure what offset the buddy's are
-
anyone know if the standard R33 gtr engine black is satin or matt finish, looks satin to me?
-
Not fussed preferably series 2 or 3
-
Hi guys chasing a standard r33 gtr front bumper bottom lips or an aftermarket carbon fibre one. Thanks
-
Rb26/30 R33 Gts-t Built Auto Drag Toy
duz10s replied to johnbarry88's topic in Members Cars, Project Overhauls & Restorations
me too -
Hi Guys, Just chasing a front bumper lip for a r33 gtr, don't mind if its the standard item or an aftermarket carbon one. Thanks
-
anyone know the values of the r33 gtr oil temp guage reading, mine has a line which starts at 70 and continues up unbroken to a point, then a break and next ready is 150?
- 9 replies
-
- oil pressure
- oil temp
-
(and 5 more)
Tagged with:
-
thanks for the tip anyone tried the Meguiars Super Degreaser?
-
Hi Guys, Keen to hear what cleaner/degreaser people have found worked best to clean the undercarriage. Surely has to be some better products than just straight degreaser you can buy from like super cheap etc. Will be using a pressure washer as well. Thanks
-
Most Common Areas of rust in R33 GTR
duz10s replied to duz10s's topic in R Series (R30, R31, R32, R33, R34)
yer inside out rust is going to be hard to see -
Most Common Areas of rust in R33 GTR
duz10s replied to duz10s's topic in R Series (R30, R31, R32, R33, R34)
thanks guys -
Hi guys, I have done a forum search and can find a little bit of info but I'm keen to understand if there are more areas that are common to rust on R33 GTR than what I note below Wheel arches Spare wheel area in boot and boot channels Chassis rails Strut top etc. I have experience with R32's but unsure if there are any subtle differences with R33's Thanks for the help
-
sort of on topic anyone know where to get new rear diff gears and pinion for R32 gtr?
-
Hi guys trying to chase down a Nissan Stagea manual transmission bell housing. Must be in good condition with no cracks.
-
Better to buy a motor already built?
duz10s replied to KerrodR33's topic in Engines & Forced Induction
have you got photos to proof this? -
Finally got the car back on the dyno after fitting a new Haltech engine loom and trigger sensors. No more miss counts, car ran perfect and was doing back to back 1100hp pulls thru the TH400 on just over 40 psi, we were being conservative given given all the small dramas we have had, left it quite rich and it has no boost control left so more wastegate springs needed if we want to lean on it a bit more. Now to hit the track and back up the numbers. HANIBL 42psi.MOV
-
Atessa not working with ABS removed
duz10s replied to duz10s's topic in Suspension, braking, tyres and drivetrain
All sorted, Atessa wasn't getting an rpm signal -
Yes Elite has been fine.
-
Hi guys sorry to dig up an old thread but I have exact same issue, error code 8 after removing ABS and no 4wd. Nothing will fix it, I have bleed the atessa that's all good, 4wd pump is ok, tank has plenty of fluid. Only time I can get the 4wd light to turn off is when the car is stopped and I disconnect the bleed connector, then the torque guage shows 10. Soon as I re-connect the bleed connecter 4wd light re appears. love some help its cooking my brain FYI, car runs Haltech elite