Jump to content
SAU Community

R324u

Members
  • Posts

    23
  • Joined

  • Last visited

  • Feedback

    0%

Everything posted by R324u

  1. I was able to make some progress on it last night by doing this just saw your post., I had to set the dash to default, what car are you using this on an r32? I’m using pin 21/ 30 for the ground but those wire colors you mentioned don’t match up to what I have so I’m guessing you have a diff chassis
  2. Yes I’ve tried to put it through the dash, just as the update but it does not do anything for me, idk I called haltech and they really didn’t help much either. Gonna have to keep messing with it
  3. Ok that was the issue wasn’t seated all the way, I Ran a test wire through but I can’t seem to find the the little deustch connectors, did the ic7 come with them or am I going crazy
  4. So for the fuel level, it’s literally one wire to get it to work and it should self ground from the pump? No Matter how I configure it it does not work correctly anyone have any ideas ? I’m using the far left wire in picture for the fuel gauge
  5. So if I’m understanding this correctly, bridge the two connections add a bulb and or resistor between the two so the alternator will charge the battery ?( Pics attached and marked )
  6. I’m assuming you’re referring the battery light (wire) on the stock cluster ?
  7. Ok that was the issue wasn’t seated all the way, I Ran a test wire through but I can’t seem to find the the little deustch connectors, did the ic7 come with them or am I going crazy ?
  8. Thank you I’ll give it a try later much appreciated !
  9. I was curious on wiring the the signals, hi beams, e brake, You just take a wire from the back of ic7 and then tap it directly into the plug off the cluster? I briefly tried it and it wouldnt illuminate on the ic7 dash, Is there something im missing?
  10. Curious if anyone has removed just the rear of the transmission from the car and was able to install it without pulling the transmission, I have a stuck speedo sensor that will not budge what so ever, so im thinking I may have to take the rear section off to do so. Any insight would be appreciated, Thank you!
  11. ( rb25 trans) anyone ever come across of a stuck speedo sensor in the transmission, I am working on a buddies car, The speedo itself wont budge at all. cant get the the cable itself to thread onto the sensor ) looks stripped). Looking for suggestions without dropping the transmission or getting too crazy.
  12. Has anyone ever come across of a stuck speedo sensor in the transmission, I am working on a buddies car, The speedo itself wont budge at all. cant get the the cable itself to thread onto the sensor ) looks stripped). Looking for suggestions without dropping the transmission or getting too crazy.
  13. Which one did you end up using ? did the same just curious thank you for your time
  14. Thanks bud, I was able to measure them finally got my kit to measure, came up with the same measurements, Thank you for your help and a piece of mind coming up with the same thread pitch and such. Gonna make a custom line, ill post a pic when its done
  15. I don’t think that’s what I need, it’s the small line that feeds the rack. I could be wrong but this is best picture I have at the moment.
  16. Thanks for the reply much appreciated, I checked it out not seeing that specific part available, there is some reproduced parts but just not this one.
  17. Trying to get some info on the attached picture, Noticed my line from the steering that feeds the rack is bent ( short line), looking to replace it with an fittings if possible i believe the one side with banjo is m14x1.50 not 100% sure what the rack would be. I noticed the part is discontinued any help would be appreciated.
  18. I was curious what people used for the transmission support when using the rb25box on the R32. I noticed the rb20 box only 1 of the holes lines up, other than welding a new piece on, Is there a stock support that would do the trick. Sorry if its been covered over and over again, I did not see any info that would help.
  19. I dont mean to bring up an old topic, but i am looking to do this to my neo, Any tips on cutting the vct hole? any specifc size hole saw or is there something you used ?
  20. I was looking to get my covers powder coated, I've come across information that it is a Silica Breath (EYO) , I was wondering if anyone knew of any powder coating paints that were available to replicate this color, Only thing i found was airbrush paint, any help would be greatly appreciated! Thank you!!!!
  21. I have aftermarket Cusco adjustable pillow tension rods , So might be ok in that aspect. Just trying to figure out my options for the moment thank you guys!
  22. I've read a few things that the S14 and ECR33 share the same Front Lower Control Arms and others say their different.. Not sure which is correct, I am looking to place these on my R32 GTST, Any Help would be greatly appreciated!
×
×
  • Create New...