1400r

"if you're gonna complain about shit - maybe try not to get EVERYTHING for less than terry's cost price " huddy "well im not sponsored so i dont automatically get that - must haggle " Adz no one gets cost or below cost I dont, Huddy doesnt and no one should how the hell would the shop stay open if it did so you must not haggle over every little thing normally it will just piss us off especially if u are trying to get it at what you think is cost maybe I'll try asking optus for a item/service for half price and see how far that gets me I treat people how I would want to be treat when Im shopping seeing as Ive worked in alot of retail shops before I know what its like on the other side of the counter Haggle to much and Terry's likely to through you out or drag the item home tied behind his car rather than sell it to you lol anyway Adz spend the $14 so you know for sure Marky didnt even drive your car how pissed are you gonna be if you swap them over and the noise is still there

baaah not sure it is even wheel bearings like I said today $14 pedders sus safety check and you'll know for sure what the problem is and then go from there

viva garage have then saw them on there site yesterday when I was looking for a mate

nah all R32's were 4.38 auto and manual ca turbo s13 were also 4.38 with a 20 with a 25 box I'd say you'd need the short ratio still with a 25 motor and box or a stroked 20 the sr s13 ratio might be better all depends on the track you go to most though to

changing to s13 crown wheel and pinion would fix that 4.083 ratio vs 4.38

"btw ryan i finally have driven my car with the 5 stud i got off you guys... front wheel bearings are shot... hope terry can give me a hand!" your joking right you mean you didnt put new wheel bearings in when you swapped them over...? cheap fix would be to put your old ceffy wheel bearings in assuming they'd fit that help

nah after hours mate

hmmmm the laugly conversion

boss wants Huddy and I to five stud works skid ceffy using 5 stud gear off a stagea front and rear cross member we have a work just read that you can't use r33 stuff to five stud a s13 seeing as there around the same era thought I'd ask here before we get stuck into it stagea setup we have seems to have the same brake setup as the ceffy has atm I'd much prefer just to stick the motor in (T04r mmmmmmmmmmmmm) but he wants five stud so Ive gotta be a good little worker lol

just jk mate big bummer after just getting your car back gtr front guards,lights and front bar ?

hmmm might need to change your name to R32 4door crashing? what the hell were you doing ? skids with Adz and pushing to hard to keep up? lol

the cars for "jdm drift"? so your gonna cut the Vin out of the front cut and weld it into your 31? full eng check mate

I got 230rwkw with hks fcd so I dont think a remap will have any problems making that

"personally i see figures like 230, even 280rwkw as a joke for the RB24. When is someone going to crack the 300-350rwkw mark with an RB24? will it HAVE to be me? (if i eventually go through with it, and don't chose RB30DETT)" Errr your joking right 32 gtst imported by my work 2.4 + T88 = 405rwkw all in a package that looked like a stocker from the outside and 355rwkw at a SA SAU dyno day so its already been done a proven japs build tough cars the end Im sure Huddys package would make alot of grunt to if he put a bigger turbo on than the 2530

got a 32 stock turbo minus oil, water line and dump $150 off my 38,000km 32

skids tonight dont be soft

mates got a s13 one he wants $210 side mount suits bride fixed backs etc

no prac for you?

check out Nathan G1's 33 355rwkw

look up the 270R 200sx tuned by nismo have a look at what they did it would be hard to spot if yor painted the whole lot in the factory colour the hole I cut is very small and only just behind the radiator shroud and stops just before the rocker cover hmmm maybe dont have a look lol just refreshed my memory and its not how I remember it my advice cut hole in bonnet not frame no one likes a floppy bonnet fill hole with mesh paint mesh black tada function without the wank

cut a hole in my sil's bonnet the other day left the frame work in still seems to keep the temps just under half way now probably only works when sitting still but it does seem to work

sic alloy pedals put them on and I wont speak to you ever again lol

eh water damage info was what the auto elec said huddy took it to for me

z imports in SA have a few 4 door doors if you get stuck

sorry guys the HC is fine its the pfc thats stuffed i.e water damaged it doesnt seem to want to power up the HC although the PFC still seems to run the car fine for now and the HC runs fibe on Huddys FC