Jump to content
SAU Community

Pyren

Members
  • Posts

    32
  • Joined

  • Last visited

  • Feedback

    0%

Everything posted by Pyren

  1. by rotating the motor i mean to dismount the plate on the motor and mount it different
  2. Hi mate! yeah as far as I can remember u need to rotate the motor in the correct position and then mount the arms (linkage). the motor always does the same movement. u need to think yourself into and try it a couple times. i think my mounting position was was 90 degrees horizontally pointed to the right side if you are looking at it from the front of your car but not sure anymore best way to double check it is do draw the motion on a sheet of paper and connect the motor to really see how it moves
  3. Hi folks, ive got a weird issue that my wiper arms are acting downwards instead upwards. I removed the motor during repainting the bay, and now its somehow wrong. ive never taken the plate off the motor which is hold by that one nut. i just clipped the arm out and now im having the weird problem that my motor runs the knuckles first a bit up and then downwards instead upwards. how could this happen? Is there a way to relearn the motor, to set start and end position? It seems it is just acting in the opposit way as it should... Thanks in advance
  4. Thank your very much!
  5. thanks for the reply! yes IGN was on when trying it and I also know how the bleed mode should work. My problem is that the pump wont turn on if I open the bleeder. Normally I should give it 1 sec blurps to bleed but it simply does not do anything when I open any bleeder. Where can I see codes on the attessa unit? like directly on the unit in the trunk? clogging shouldnt be an issue as the system was not taken apart. i only diconnected the line to the back of the trans as I had the engine out for a rebuild.
  6. Anyone had this issue before?: i was trying to bleed the attessa (r33 gtr vspec) and the strange issue that I have is that the bleed mode of the pump does not work. Ive done it 2 years ago and it was working. so when i disconnect the white connector under the dash the pump only starts if i turn ignition on, but when opening the bleeders it wont start on loss of pressure. if the connector is connected the pump won't do anything no matter what. also strange is that there is only very little fluid coming through the diff bleeder, as there is no pressure. On the other hand there is good pressure on the transfercase bleeder. I have no ECU connected, never touched any wiring on the attessa sytem and fluid level is ok. anyone can help?
  7. Hi guys, I forgot to install the breather hoses, are they important or can i leave the hoses towards the ground? Best regards
  8. alright mate thanks!
  9. alright mate thanks!
  10. Hi guys, I took my gearbox off (R33 GTR) the other day and I made a mistake. instead of simply removing the pipe at the end of the gearbox, I removed the whole Flansh (Unit) where the pipe is attached to. Now my question is: Is it fatal? and there was a lot fluid coming out which I assume was the Transfercase fluid. Is that correct? So if I assemble it again can I simply reseal the unit and fill the transfer case and bleed it or was the fluid a different one than the on out of the transfer case? Is there anything else I need to take care of? Best regards!
  11. thanks ill have a look!
  12. teah we looked at it it seems to be fine, we bled the lines and changed the whole brake fluid. next step i am going to look at is too shortcut the clutch damper. maybe de piston of the damper is not sealing well. friend of mine had that problem on a Nissan Patrol. Ill give an update. Thanks in advance!
  13. Also I dont think thats bent, the pedal feels like it should, or wouldnt i recognise it?
  14. what do you mean with cracking and bending? u mean the master cylinder? thanks
  15. Thanks for the input, i am pretty sure that we managed to bleed the lines well so that point is done. If the clutch is nearly done then it is finde for me but my concern is that its not opening fully. I just want to sort that out before i do something else.
  16. Hi guys, I have a problem. First of all I do have a Twin plate clitch in my r33 gtr. When pressing the clutch pedal it make some rattling noise, after reading and gathering some info this is considered as normal with those type of clutches? The bigger problem is that my gearbox sometimes gets stuck in 1st gear when im stopping with the clutch fully pressed it still wants to go forward. Also its really hard to change gears sometimes. I ve done an gear box oil change and bleeded the clutch line (both damper and slave cylinder). Nothing helped. I would need some advice where too look at next. Could it be that my clutch pedal needs to be adjusted? (clutch feels heavy but normal and the point where it grabs is late) Please give me some advice :) BR
  17. Thanks a lot that helps me !
  18. Hi folks, so I am looking to buy a set of front seats, and for that i need to get a seat bracket. Can anybody tell me if Seat brackets from the 300zx are compatible with the R33? An onlineshop is offering those or the ones from the r34. Not sure if any of these will fit into my r33 ... Thanks in advance
  19. I forgot to mention that the bulbs have been replaced with LEDs. So either they are broken completely or not
  20. Hi, i have an issue. When i turn on the lights before starting the car, all dashlights are working properly. As soon as I start it up and drive the lights behind the speedometer begin to flicker and turn off completely. Sometimes they come back on randomly. I also searched for a dimmer but aparently I can't find one in there. Have anyone had such an issue before or can anyone help? I would like to prevent stripping out the interior :D Thanks in advance :)
  21. Thanks Seems a bit high or not?
  22. Haha no im not that type xd livin in europe (austria) my only goal is to keep that car healthy ✔
  23. Thanks so much for that info. Helps me a lot. Btw i have the power fc installed, how high should i set the rev limiter? Any suggestions?
  24. Well cool thanks xD
  25. Hi guys, This questions might be stupid but when driving with a rb26 (r33 gtr), how much do I need to care about revs, fast throttle let off and stuff like this. My car has around 380 crank hp and 310 whp. (Bigger injectors, twin plate clutch, stock boost) Of course regular maintenance is done BR
×
×
  • Create New...