Jump to content
SAU Community

heller44

Members
 View Profile  See their activity

  • Posts

    1,121

  • Joined

  • Last visited

  • Feedback

    100%

 Content Type 

Everything posted by heller44

  1. heller44
    Did you answer the question posted previously, are the turbos ball bearing now? Thanks, James.
  2. heller44
    http://www.skylinesaustralia.com/forums/in...c=35733&hl= this should help..
  3. heller44
    I'd like to buy a set to suit an r32 gts-4. Could you please pm me the details for direct deposit.. Thanks. James.
  4. heller44
    Genius.. Had mine measured today when going over the pits. 15mm back on the left trye as well. (15mm is the limit of what they would allow.) Will go through all my bolts as well.
  5. heller44
    .Drivers side rear quarter window? Is the seal still good on it, intact? Are you willing to send to perth?
  6. heller44
    Thanks, that does help me a bit.
  7. heller44
    G'day. I'm looking for inner and outer tie rod ends for my car. Does anyone know where to get them from? or the correct part number for both pairs? Thanks for your time. James.
  8. heller44
    G'day. I'm looking for somewhere to buy replacement inner and outer tie rod ends for my car (front end). The car is an '89 r32 gts4. Looking for original type replacements, not rose joint. Does anyone know of a supplier? Or the actual part numbers? FAST gives me one number for inners, and one for outers across the gts-gtr range, I've been informed that there's 4 different variations available. Thanks for your time. James.
  9. heller44
    I recieved mine from carmate last week, panelbeaters have it at the moment, fitting it after all the other body repairs are done. Initial impression is that it looks ok, but know nothing about how it actually fits on the car yet. will have pics in 2-3 weeks probably. gtr front on gts4. wanted original abs plastic one. oh well.
  10. heller44
    Do you still have the bonnet?
  11. heller44
    I am looking for the drivers side rear quarter window. Are you willing to post to perth? What do you want for it?
  12. heller44
    Do you have any idea on approximate cost to send to perth?
  13. heller44
    Let me know if you change your mind. James.
  14. heller44
    try putting a question mark ? behind the .png and it'll work.
  15. heller44
    rb20det in the r32's
  16. heller44
    seen these for sale yesterday, can't find the pic again but they are g max wheels. similar to the work miester that are posted later down but are a 3-piece design with the bolts on the rim outer.
  17. heller44
    auto?
  18. heller44
    http://www.skylinesaustralia.com/forums/in...into%20R32&st=0 here's a nice little write up of what needs doing..
  19. heller44
    Isn't 10 psi stock for an r32? I think it is...
  20. heller44
    Oil isn't going to magically disappear. It can only be leaked out or lost in the cylinder. Get a compression and leakdown test done, as others have said. But it looks like rebuild time. rory_kiernan : stock r32 is 10psi? and you've gone to 12psi with not much else done...
  21. heller44
    Just had a look back through your previous posts about the rb30det, very impressive.. didn't see the bit under your name before.. You were going to put this motor into the gts4..?
  22. heller44
    What does it have in there now? Would the 25 have a 25 box as well? Has the 25 been in there previously? Otherwise it looks very nice.
  23. heller44
    It's part of the emissions equipment. If you don't have it you can be defected.
  24. heller44
    R32Big_boy, when did boost arrive before the fitment of the jaycar unit?.. and comparison point to the rb20 original turbo. Thanks.
  25. heller44
    Also remember that you aren't running at 100% duty either , so the current flow will be at a reduced ratio following along with the duty cycle of the injector. (unless you are right on the edge..) Better to be safe than sorry though.
×
×
  • Create New...