nizmo_freek

Heres a few pics, probly have more somewhere but cant find them

Thats because it has a gtt front bumper And yes, back on topic. It is probly best that you go and test a r33 and a r34 for yourself to make a decision, each have their good and bad points such as r33 is lighter and less powerfull r34 is heavier but has more power r34 is newer so should be in better condition etc etc And when it comes down to modifying both are pretty similar, espcially when it comes to engine modifications.

What the hell are you talking about? If you are talking about Joe McAndrew then his car is not a gtt, its a gtr!

Looks good, were did ya get them from?

WTF!!!!!!!!!

^^^ nice, 2nd shot looks good!

Any chance you coud post or p.m me some pics after you install the pipes? would be interested to see what they look like, ive never knew cusco made alloy intercooler pipes for our cars.

They will fit fine. Here are my size's Front 18x8 +28 Rear 18x9 +30 The 17" xd9's you are looking at getting will sit like this compared to what mine sit like. Fronts = will sit 4mm closer to the gaurds and the inside of the wheel will sit inside the gaurd 8mm more than mine, so these will fit fine! Rears = will sit inside the rear gaurds 6mm more than mine and the inside on the wheel will sit inside the gaurds 6mm more than mine, so these will also fit fine, but will sit inside the gaurds a little bit. To be honest i would be looking at other sizes/offsets , yes they will fit fine but they will sit inside the gaurds a little bit, not so much the front as they will extend more than mine, its the rears that will sit in quite a bit, i guess you could always get some bolt on spacers. Heres what mine look like, keep in mind that my car is pretty low so i have a bit of negative camber, hope this helps anyway! Cheers

You sure thats a 20b in that r33? Sounds more like an RB with no exhaust and big cams to me?

Just remember, Nissan's ring time of 7.29 was for the BASE model GTR, your comparing the base model GTR's time to a "modified" version of a already existing base z06, hardly a comparison in my opinion. Wait till the Vspec GTR offical runs the ring, then compare it to the zr1! And saying 90% of the people on here are "dumbarses" is a pretty bold statement!

WARLORD, do you have any pics of the actuator bracket? it looks like you have the exact same actuator bracket that i had, which isnt the correct bracket, i had to modify mine as it was causing the actuator rod to sit at an extreme angle which could have damaged the diaphram if i had left it the way it was, you will see what im talking about in the thread bellow, i ending up modifying my bracket in the end. http://www.skylinesaustralia.com/forums/Hk...Ro-t207485.html Did you buy your turbo kit from JPS-Trading?

Hey mate Did you manage to take any extra pics that you can post up? Cheers

Wont be "flaring" the guards, will just be rolling the lip back as much as possible, still not sure on tyres sizes yet, would need to put the rear wheels on the car without tyres to see how wide of a tyre will fit on there, im thinking a 245-255 should fit ok'ish lol Any chance you have any pics of the full car you could post up? cant wait to see what your car looks like now in a decent pic!

And what size tyres on the rear? Im thinking of going 18x10 +18 on the rear, looks like it might be a bit of a tight fit after looking at yours

My tein super drifts (jap spec) have more than 16 clicks, i think its just over 20, also there is somewere in the book that im pretty sure says something about do not adjust above 16clicks, but then again i cant read japanese

size/offset??

Hey guys Been having a few problems with squeeing brakes Turns out the previous owner of my car has removed all the backing plates/anti squeel shims and had installed some lucas pads which use a sticky pad on the back, i have now bought some brand new endless pads which i installed without the backing plates because i dont have any,this has made the squeeling 10x worse. I bought a set of 2nd hand brake plates for the front (nissan wanted to charge me $180 for a brand new front set, dont know how they can try and charge that much for a little peice of tin) and will be installing these soon, but i have a question Do the rears use the same type of thin metal brake plate as the front? i took mine apart and all mine have is a little thin u shaped peice of metal that clips onto the inside of the caliper, it dosent go in between the pistons and the pad. So do the rears only use this thin u shaped peice of metal or am i missing the rear brake plates too? Any help would be great! Cheers

I will most likely be going 18x9 +20 up front and 18x10 +18 at the rear, not sure on tyre sizes yet, and now after seeing yours im having trouble deciding what colour i want lol , white wheels look so nice on silver cars, especially yours!

Moonface racing? Looks very nicely made!

Looking awesome dude, probly the best size/offset setup ive seen on a stock guard gtst in a while I should have a similar setup on my r33 soon, i really need to get rid of my girly 8" fronts lolol

Coming along nicely Dave, cant wait to see the results

How about you use the search function instead of asking me and other people to find the answers for you, the info is out there, you just need to learn to search "mate". please..................

Have you searched??? Didnt think so! Seriously, use the search, there is hundreds of threads about the 3037 that would atleast have "some" of the info you are looking for.

That looks awsome!easily one of the best wheel fitments i have seen on a r33 gtst, perfect size's/offsets! Any chance you are able to get some bigger and better pics?

Possibly an air temp sensor, would be easier to figure out what it is if you posted up a pic.