Ballistic

radiator and hoses?

do u have a flywheel to go with that?

interested in the turbo. how many Km's? Been Boosted? Ceramic Exhaust Wheel? A/R's? T3 Flange? Guarentee?.. they are an old turbs... guarentee that it wont blow shitloads of smoke once on would be good.. not looking for a time period guarentee. Negotiable Price? Can pick up from GC on weekend. thanks mate. msg 0410 133 391.

http://www.bosch.com.au/sat/motorsport/dow...s/fuelpumps.pdf 910 flows 130L/Hour at 5 bar fuel pressure any other details u may need are stated in the link. a good reference for Bosch products...

have money waiting for these. need anytime in next few months. PM me dont reply here. Thank you

piccy of boost guage plz. what does it read to? [email protected]

is this off the R32 style ECCS RB20 or the NICS R31 Version?

What bearings do people recommend? Was thinking of just the ACL bearing kit...? Oil pump eh? might check it out. Would like to know some details relating to cooling properties with the speed of the coolant/water aswell. I have heard of pumping it too fast, doesn't get enuff time to cool etc. Dunno.Time for some research me thinks.

ok. Have a block and some forgies to whack in it. want some advice on getting the block prepped for some descent power (and boost) Acid Dipped Block (clean all oil galleries and cooling jackets) Bore/Hone Deck head and block. Double O Ring (Block and Head) Copper Head Gasket Crank ground - nitrided - and reground Rods Shot peened and knife edged. All reciprocating mass assembly (crank, rods, Pistons/rings, Flywheel (lightened billet)) Balanced and Blueprinted New Gaskets all round. What else is there to do? Planning to run big boost levels and a fairly big rev limit. let us know. I have the block, pistons and bottom end ready. ust finding out info on some of the toughening procedures that can be carried out. thanks boys. Mitch. Also explain what it does etc.

someone please take it.. at this stage it looks like im jst going to have to stick with the HUGE inlet tract on the ET turbo combines with this cooler. ****. i got a BB T03 going on her as well.. its going to be lag city.

piping, hoses and clamps woulc very depending on what material used. for mild steel budget maybe $200 for alloy maybe $350. It all depends on your pipe route too. and also the silicon hoses you use. You can go for high grade clamps with high grade silicon hoses and it costs you, but just the generic stuff works well enuff. Also depends on your friends so yeh maybe take what i say as a general guide.. aot of the time you can utilise some of your stock stuff in way of hoses and clamps, even the piping up to the throttle body can be retained.

Just want to know where to get flanges cut. I want a header Flange between Exhaust manifold and the Head, and a Flange For Manifold to Turbo cut out of 3/8" Mild Steel. Also Flange from the turbo to cooler pipes in whatever is suitable??? im guessing some sort off ALLOY? Also from the Turbo to the Inlet tract ie. between turbo inlet and afm/filter. Im sure these arnt hard.. maybe someone has had experiences in the past with places that are cheap? Im going to ring round exhaust shops soon. Thanks.

then that would be 25T or i guess any RB25DET transplanted into something else.

Got to go ppl. CMON.. SOMEONE MUST WANT THIS COOLER - I HAVE ONE GENUINE INTERESTED... BUT HAS SINCE NOT GOT BACK TO ME CAUSE WAS ASKING HIS MATE. PM ME WITH OFFERS IF YOU HAVE THEM (nothing stupid).. ALTHOGUH I AM NOT WILLING TO SWAY ON PRICE MUCH. AND THE COOLER IS NOT A KIT OR DOES NOT COME WITH PIPING... I AM SUPRISED HOW MANY HALFWITS HAVE PM'D ME SAYING.. ILL TAKE IT IFF ITS GOT PIPING HOSES AND CLAMPS WITH IT. YEH AS IF!!!!! WOULD BE AROUND 1200-1300 IF IT CAME WITH KIT

if you read my post properly It says new controllers for 900... and im offering 600 for this second hand one.... actually! i have since seen even cheaper controllers from guys that bring stuff over new from japan.. like the hikari doods. in the region of $840-$870. have spoke to a mate of mine who knows guys personally that do this.. and reckons can get me mates rates around $750 in box new. However i still would prefer to pay 600 ff you if you can let it go and couldn't care less if its 2nd hand. i am gunna dedicate my money by end of the week. let me know! check PM also nisstrust