Tangles

yeah I know, 3 sets of rims Ive got didnt fit past the calipers, havent got the funds atm to buy new rims seeing the marriage is finished, house for sale & walking away with $0 decided best for my 2 kids to have my half of the house sale, would rather them have a rooftop for as long as they need got to write up a legal document to safeguard their half, f**ked if the ex will take everything, shack up with someone else who then rips her for half of MY assets 50mm extended wheel studs all round with 10mm spacers used to use them, been around mallala last October and used on road for half a year, should be aok with these long studs tho one day will get rims that clear the calipers, just cant at the moment

Stagea Series 1 parts for sale. Pickup south adelaide, will post for minimal charge * front brake calipers, with braided brake lines, with 2x sets of brand new bendix advance pads $100 + $20 post * front brake rotors, standard. non-drilled, non-slotted. near new (with surface rust from rain) $80 + $20 post * 10x front 50mm wheel studs, 13.75mm knurl diameter, 10x rear 50mm wheel studs, 12.75mm knurl diameter brand new, bought 20 of each, so 1 whole set not needed $100 with free postage * DBA 4000 slotted rotors, brand new (with surface rust from rain) $150 + $20 post * standard front & rear anti-sway bars $50 each - will not post, sorry, too large * standard front drivers seat, pulled apart from standard rails, excellent condition $50 - will not post, sorry, too large PM me please, rarely look here so wont notice your reply

324mm wilwood brake kit installed, again 20x 50mm extended wheel studs needed (+ spacer) to get rim over calipers charging a very flat (new) battery then out for skids well, bed in brakes and new ku36 tyres anyhow

+1 for toshi although Id recommend at the least add on a safc or emanage to fine tune the ecu remap chip 250rwkw from my Toshi "mail-order" ecu remap chip + aem fic/8 (like emanage)

Stagea series-1 wheel studs - front = 13.75mm knurl diameter - rear = 12.75mm knurl diameter 50mm extended wheel studs fit beautifully

love it today finally finished off the front and rear 50mm wheel studs. didnt take off the hubs, didnt replace footbrake pads. needed 50mm extended wheel studs to fit wheels over the 13" 324mm Wilwood brake setup. about to test drive this arvo - flat battery atm, so charging that up, get some air in the brand new unused KU36 semislicks fill with fresh fuel, give her a beaut wash to get rid of the gumtree crap all over her, and test the brakes/tyres fs: 10x front 50m wheel studs, 10x rear 50mm wheel studs, suit Stagea S1. front 13.75 knurl, rear 12.75 knurl - $100

I found rocking horse poo once * may or may not have been the cat, most likely the other cat

japanese import spares? jap motor sports? one of the inporters will have a front cut available for parts ebay?

ah shite read this thread, lost 12 IQ points oh noes

pm me please

setup my bicycle and went for a ride just before came inside afterwards, took the step down into the family room, leg didnt hold and crumpled to the ground !!! left knee totally gave way wowsers

ah shit was that you? sorry didnt mean to, well, not much anyway

My local Sprint Auto parts looks after me. Discounts aplenty Just got iridium sparkies, 10-50w Penrite oil, 516a Ryco oil filter, engine oil flush, radiator concentrate & distilled water, plus bendix front brake pads to service the Ford Escape.......

tom cruise on the right will be late for mum's roast damned wheel hub. going to try again. been a bugga of a job to get one hub off the car (LHR), no luck yet.

More into Twister sorry

haha, we could find a corner and party together??

excellent results please update Dyno Results post with full list of mods well done, 245awkw is sweet 'aint it?!

I'll put one up for you then

+1 with grille, I do Like mind you, I like the lambo doors on that S1 stag as well. looks good tbh would be handy for tight car parking areas

Does the stagea / R34 skyline tiptronic auto gearbox have its own separate auto ecu, or is it incorporated into the engine ecu? Looking at buying a R34 GTT auto box, already have steering wheel with shifters and the centre console shifter mechanism unit (complete) Does the box have its onw ecu or is it part of the engine ecu? Would like to do this when i drop in the rb26dett built engine (wont install a manual) cheers, unsure.

PM sent re: gearbox

man that's horrible at least they can do is man up to the fact they f**ked up, and arrange a free tow home bastards

plz see: wanted to borrow. cheers

thanks mate for the suggestion. Looks like thats exactly what I need http://www.tridon.com.au/Products/Product....530&P=68973 have asked to borrow one from SAU:SA, we'll see what happens. might have to plead to borrow one from my tuner if all else fails, who has shifted waaay out to whoopwhoop land

Need to borrow URGENTLY a mechanical separator / puller ie HUB-Puller http://www.tridon.com.au/Products/Product....530&P=68973 Cant remove my LHR stagea hub without one. Anyone willing to loan out their unit for half a day? Please? thanks in advance if anyone can help me