reaper

Hi Guys, Got a few parts here I didnt end up using for my build or im not using anymore. All prices are a little negotiable and pickup in Rouse Hill, NSW is preferable but will post at buyers expense. 1. 6 Speed Gearbox out of an S15 $800 ONO Came with my new motor but I have a dogbox so no need for it. Shifts perfectly and comes complete with sensors and clutch fork. Motor it was attached to was out of a low km aus spec S15 that was unmodified and clean. 2. Set of S15 Coilpacks with Coil Pack Loom $150 ONO Were working perfectly with motor but im replacing them with a CDI setup so need for them anymore. All are in good condition and it includes all plugs and the associated loom. 3. Full engine loom and factory ECU out of AUDM S15 Turbo $400 ONO As above comes with all plugs and wiring aswell as ecu to suit motor. 4. T28 with manifold, lines and intake elbow $600 ONO Perfect working order comes with everything needed to bolt onto an SR20 minus the dump pipe. Best way to contact me is via 0403858714. Thanks, Brett

Hi Guys, Got a few parts here I didnt end up using for my build or im not using anymore. All prices are a little negotiable and pickup in Rouse Hill, NSW is preferable but will post at buyers expense. 1. 85 lb/hr Fast Injectors (900cc) *BRAND NEW set of 8* $500 ONO Bought these for my L98 with the intention of going E85 but never got around to it. Have now stripped that car so no need for them. They are to suit an L98 but will work with LS3 and LS7 may work with LS1 or LS2 depending on rails and intake manifold. They are brand new as pictured below with new top and bottom o rings to match. 2. Aeromotive A1000 Fuel Pressure Regulator *BRAND NEW* $250 ONO Bought this with the injectors and rails but didnt use any of them. It is the -6 in and out version and is fully adjustable. Black in colour and brand new in box. 3. VPW Fuel Rails *BRAND NEW* $200 ONO Same as above to suit L98, LS3, LS7 may work with LS1 or LS2 depending on the intake manifold used. Anodized blue in colour and brand new in box. 4. L98 Alternator *BRAND NEW* $250 ONO Bought this brand new from Holden for $350 but ended up needing an LS1 one as I was using an aftermarket ECU. Completely brand new and never used. To suit L98 but may also suit later generation LS2 along with LS3 (any LS where the alternator is controlled by the ECU). 5. L98 Starter Motor *BRAND NEW* $250 ONO Bought this brand new from Holden for $350 but it didnt clear the steering shaft in my S14 so had to swap it to the other side. Comes with 2 brand new Holden bolts to suit and has never been used. Was bought for L98 but will suit LS!, LS2, LS3 and LS7 aswell. Best way to contact me is via 0403858714. Thanks, Brett

Found one, please close

Hi Guys, Im after a standard R33 GTST Non ABS 4.11 Diff. It can be welded or not doesnt matter I just need the whole diff as ive blown mine. Would prefer if it came with the 5 bolt half shafts but dont need the driveshafts. Happy to pickup around Sydney so let me know what you have. PM me or sms on 0403858714. Thanks, Brett

Here is a pic of the actual seats.

Hey Guys, Ive got 2 Genuine East Bear R34 GTR seats with Bride copy low max rails to suit S13/S14/S15 and will suit A31/R32/R33/R34 by elongating the rear outside bolt hole on the rail. These seats are the most comfortable bucket seat ive ever owned or sat and im only selling them as my car is no longer registered and im in the process of going a full weld in cage so have swapped to a fixed back. They worked well at track days and were perfect for street use even drove to qld and back in them without any pain or discomfort. They are in good condition and they look like the image below however they are a light grey in colour not black. Im asking $1400 ONO including rails and will not split the rails unless I have a buyer for the seats on there own. I am located in Rouse Hill, NSW and dont really want to post them due to how big they are so pickup definately preferred. Will have proper pictures up tomorrow when im at home. Any questions pm me or ring on 0403858714. Thanks, Brett

SOLD

Hey Guys, I have up for sale 2 Firenza 215/40/18's. These were fitted to my wheels but clearance was too tight so I swapped to 225/35/18. They have never been driven on just fitted to the rims and are BRAND NEW. $180 ONO Pickup in Rouse Hill, NSW, 2155. Not really interested in posting something this large and if you have any questions sms/call me on 0403858714. Thanks, Brett

SOLD, Please close.

Yeah its slightly more than 3 litres. 3.17 or so I think!

Here is a better picture so you can see everything it comes with.

Hey Guys, Up for sale is my 3 quart accusump kit which is brand new and comes with everything from the original box. I bought this for my new motor setup but dont really need it anymore. It comes with everything pictured below so just add lines and your on your way. Price: $400 ONO Im located in Rouse Hill, NSW and pickup is preferred over post but will post at buyers expense. Any questions please contact me on 0403858714. Thanks, Nrett

bump

Need this gone guys, price negotiable!

Hey Guys, This clutch was custom made for this setup and has no problems at all with the power but is fairly soft on the driveline unlike other twin plates ive used which blow boxes constantly. Clutch has 1500km's on it and cost $2600 to be made. Best part about these clutches is they are easily rebuildable if you ever need to. Clutch is in perfect working order and you can see how good condition its in when its apart im only selling it because I sold the entire setup. Price: $1400 ONO Clutch is located in Rouse Hill, NSW, 2155 and would prefer pickup over post but will post at buyers request. Price is negotiable just dont try and lowball me too much Either pm me here or ring/sms me on 0403858714. Thanks, Brett

Hey Guys, Im about to swap setups again so this stuff has to go. Setup cost me alot of money and have receipts for most of the big purchases. Car made 288rwkw on 20 psi with full boost at 3700rpm on a 2L motor so its plenty responsive and pulls hard all the way to limiter at 7500rpm however I have been running no more than 16psi through it at the track just to keep it all 100% . I'd love to sell it as a package but will split it up if I dont find a buyer for everything. Setup is still in the car and can be seen running for now but will be out in a week or 2 so you will have to be quick for that. Here is a picture of the entire setup and can get seperate picture of everything at request (once its apart of course). 1. SR20DET $2000 ONO ARP head studs, tomei poncams, nitto metal head gasket, rocker stoppers, extended sump. Will come complete with alternator, p/s pump etc. Head was refurbished about 500km ago if that and thats when the head studs and metal head gasket went in. Bottom end is standard but was refurbished about 10000km's ago and runs absolutely fine. Compression 150 accross all 4 cylinders and doesnt breath at all. The motor itself is an S13 motor which ive been running in my S14 fine. 2. Twin Scroll 3076r High Mount Setup $4000 ONO Bought this kit off Powertune and its seen maybe 1500km's if that as the car barely gets driven. Have not had one issue with the setup works great and is very responsive. Comes with 2 x Tial 38mm Slim Wastegates, 3076r .78 twin scroll rear housing, PowerTune steam pipe high mount manifold, dump pipe, intake pipe, 2x screamer pipes, all turbo lines. Dump pipe and screamers wrapped in heatwrap. Turbo rear housing and manifold ceramic coated. Cost me almost 6000 all up for everything (have receipts) but its a real responsive setup full boost by 3700rpm and doesnt taper off even at 7500rpm rev limit just wants to keep on going. 3. Z32 Gearbox Conversion $1000 ONO This is one of Nigels kits so comes with modified bellhousing, modified shifter, gearbox mount and tailshaft. The box itself was freshly rebuilt about 1500km's ago however it has a loud main bearing knocking noise that goes away once the clutch is put in. Still selects all gears fine so I dont imagine itll be anything too bad and will probably fix it before I sell it so the price will go up accordingly when that is done. The mount will work in S13/S14/S15 but the tailshaft will need to be shortened for an S13. 4. Genuine Greddy Plenum $650 Will come with standard throttle body and is to suit S13 SR20DET. Its genuine and is polished but could do with a bit of a cleanup as its faded in spots. 5. 4 x 1000cc Injectors and Top Feed Rail to suit $650 ONO They have 1500km's on them and suit S13 SR20DET. Comes with everything needed to bolt it up to your setup and looks like new. 6. NPC Custom Twin Plate Clutch $1800 ONO This clutch was custom made for this setup and has no problems at all with the power but is fairly soft on the driveline unlike other twin plates ive used which blow boxes constantly. Clutch has 1500km's on it and cost $2600 to be made. 7. Blitz SBC ID3 Dual Solenoid Boost controller $450 ONO One of the best boost controllers on the market and has no problems controlling the 2 gates. In great condition and comes with all loom and lines required. 8. Saber S13 SR20DET Radiator $250 ONO Great radiator that has worked well just wont work with my new setup. Is only about 1500km's old aswell. 9. Saber S14 FMIC Kit with piping to suit high mount turbo setup $350 ONO Once again in great condition just have no need for it anymore. The turbo side piping has been setup to run through the stock hole in the S14/S15 which makes it look real clean. Inlet side runs through battery tray like usual. I think thats pretty much everything I can think of for now but may add extra parts as they pop up. Setup is located in Rouse Hill, NSW, 2155 and would prefer pickup over post but will post most of the stuff at buyers request. All prices are negotiable just dont try and lowball me too much Either pm me here or ring/sms me on 0403858714. Thanks, Brett

Price drop $500 need them gone guys!

Price drop $500 for the injectors and $400 for the manifold need them gone guys!

Price drop $400 need it gone guys!

bump, prices are negotiable!

GCG Stainless Steel High Mount Manifold RB26 - $500 This manifold is about 10000km's old and is in good condition. Was working perfectly well when I stripped the car and has extra bracing to stop it from cracking. I also cut slits in between each runner so it wouldnt warp like most other stainless manifolds. Suits a 44mm external gate that sits quite low. Had a fair few cops go over the car in its time and not one spotted the gate as its hidden from view. Either PM me here or sms me on 0403858714. Parts located in Rouse Hill, NSW, 2155 and pickup is preferred over post. Thanks, Brett

6 x Near New Siemens 750cc Top Feed Injectors - $600 ONO I bought these, tuned the car then promptly put the car into a wall that night and stripped the car so they have 150 kilometres on them if that. I have the receipt for buying them brand new for $858 not including the seals and as you can see in the photo they look brand new. They were running in an RB26 but will suit anything that takes Top Feed style injectors so RB20, RB25/1JZ/2JZ with conversion rail etc. Either PM me here or sms me on 0403858714. Parts located in Rouse Hill, NSW, 2155 and pickup is preferred over post. Thanks, Brett

bump

Hey Guys, I've sold pretty much everything else from my old RB26 setup so need these gone. 6 x Near New Siemens 750cc Top Feed Injectors - $600 ONO I bought these, tuned the car then promptly put the car into a wall that night and stripped the car so they have 150km's on them if that. I have the receipt for buying them brand new for $858 not including the seals and as you can see in the photo they look brand new. They were running in an RB26 but will suit anything that takes Top Feed style injectors so RB20, RB25/1JZ/2JZ with conversion rail etc. GCG Stainless Steel High Mount Manifold RB26 - $500 This manifold is about 10000km's old and is in good condition. Was working perfectly well when I stripped the car and has extra bracing to stop it from cracking. I also cut slits in between each runner so it wouldnt warp like most other stainless manifolds. Suits a 44mm external gate that sits quite low. Had a fair few cops go over the car in its time and not one spotted the gate as its hidden from view. Either PM me here or sms me on 0403858714. Parts located in Rouse Hill, NSW, 2155 and pickup is preferred over post. Thanks, Brett

Got a pair, please close.