varun_gtr

im not using race fuel my car will be run by rh9 rules, i dunno how the hell he made that much power with 2530 but damn that would rip on the street, i had 2530's before i decided to do all this. i dont want 1, i want 2, i knew the 3037's would make the power but i want the light switch effect of the trust turbos not the gradual ball bearing build up its good but ye i dunno. a few of the rh9 cars do run 3037 that is y i originally got them but a few also run t67's anyway thanks for ur input every1 twin t67 is the go 4 me.

i just wrote 1000 to get ppls attention i want to make 750 at the wheels its impossile to calculate to the flywheel power unless the engine goes on an engine dyno. i know it will be late delivery im not expecting anything before 5000rpm but hopefully full boost by 5500-6000rpm would be good, the 2835's i dont think will do it, i had 3037's b4 and without trying them got rid of them.

hey ppl, i have all the neccessary equipment to do it (motec, fully sik engine its still a 2.6 well 2.65 now i guess, fully sik head ported with big cams, springs & retainers standard springs, fuel system, ignition system and even some happy gas). Im pretty set on a particular setup which is twin t67 25g with the 8cm rears (our buddies in jp use the 10cm rears but i was hoping to reach boost a little earlier because its a street car). Theres sum switched on guys in here so i thought i'd ask. wat turbos should i run to make atleast 750hp at the wheels on pump with additives "toluene". i want to keep it twin every1's suggestions would be very much appreciated thanks guys.

ye im going bigger just for a bit of overkill im not sure if i'll make to the power theshold of these cams but just incase, but these cams with the right bits can produce 450kw+ and low run low 10sec passes and has been proved by a mob down south with a sliver r32 gt-r.

Tomei Poncams direct bolt in for r32 & r33 rb26 will not fit in r34 rb26 because of different crank angle sensor drive. Very noticable change throughout the whole rev range sounds tuff on idle. The inlet cam has done around 6000km the exhaust cam is brand new and never been run and cost me $680 on its own from high octane racing in sydney. Part numbers: Inlet cam - A2691N Exhaust cam - A2691X $850 delivered anyway in aus. located in brisbane. Contact me on 0401376402 or [email protected]

****Tomei step 1 cams for RB26, 9.2mm lift 260 degree duration inlet and exhaust. Perfect for a street car work well and maintain drivabilty. Tough sounding lumpy idle can be run with a standard ECU, work well with adjustable cam gears. Exhaust cam is brand new has not been run paid $720 for new exhaust cam alone, inlet cam has done nearly 10k. $1000 negotaible. ****RB26 HKS adjustable cam gears, puple center with green outer, done nearly 10k on engine. $350. ****Nismo 550cc injectors for RB26 or to suit any top feed injector rail. direct plug in for RB26 genuine nismo item no cutting and joining new plugs to fit. $750. ****Power FC brand new with hand controller 32 & 33 RB26. $1300 ono. ****Motec M600 with complete loom and brand new 3 bar map sensor for any 4or6 cylinder no extra features enabled, features can be enabled cheap if u would like any. has nitrous control already wired into the loom. if any serious buyers 4 this one will negotiate price. will try to take sum pics asap. urgent sale please email me at [email protected] or sms me on 0401376402. Thanks

i kno its a bit out of place on here but im selling it 4 a mate, its a mazda rx7 series 4 with a toyota 7MGT-E with an IHI (apexi) RX6 turbo, big intercooler, adjustable coil overs and all he stuff you need. the only thing left is to do the wiring, the engine does run. If anyone is interested pm me, selling for $14,000 ono and i can take pics if any1 is interested, located in brisbane (sunnybank), was origally built to be drift car. needs to sell very soon to pay a lot of his fines.

JE Pistons and conrods to suit RB26DETT with stronger gudjeon pins & standard conrods which have been race prepped & strengthened ie. Beam Polished & Shot Peened. Standard little end bushes in the conrods have been pressed out and replaced to allow for a slightly larger and stronger gudjeon pin to avoid pin flex. Pistons are custom JE pistons which are designed to fit these pins and have provision for a larger top piston ring to allow for better sealing. Both items are to be sold as a matched pair and will not be seperated. Able to withstand 600-700hp pistons make very little noise on cold start up and when at operating temprature do not make a sound. Out of an RB26 engine with 86mm bore, both items are blueprinted (balanced) and ready to go. No damage and are like brand new in perfect condition. Standard conrods cost $125 each to prepare and custom pistons cost all up $1550. $2300 worth of parts in near new condition. Being replaced with pistons and rods to make a longer stroke and fit a larger bore. Located in Brisbane $1300 o.n.o email: [email protected] mobile: 0401376402

Urgent Sale JE pistons and strengthened rods were previously run in my engine and are being changed for a what i hop to be a stroker kit. JE forged pistons standard bore size, only half a millimeter over standard bore so will fit with a light hone. The JE pistons can withstand a lot of power and only have to be sold because i cannot use them with any stoker cranks or rods. Standard connecting rods, race prepped and strengthened, beam polished and shot peened and are in excellet condition. Rods are capable of holding up to 600hp at the flywheel with all the right assistance, oil cooler and larger oil pump etc. Prefferably want to sell those pistons and rods as a set for $1300 mind you they are second hand, condition is perfect. These as a set will handle 600hp day in day out and JE pistons must need warming up at idle for a good 7-10 minutes time before driving. These rods are sized for the gudgeon of the JE pistons so no furhter work required on parts, balancing etc. Also for sale, second hand perfect condition hks con rods with stronger carrillo rod bolts to avoid bolt stretch. Have been crack tested and balanced, but will need minor balancing to suit your crank and pistons, $1400 for the hks con rods and stronger bolts. If you are genuinely interested let me know i am negotiable on prices for both things. email me [email protected] sms or call on 0401376402. And if you are inquring on here, please pm or email me because i dont know how to check my posts . remember its an urgent sale, thanks ppl.

my thanks go to Ginkgo Biloba, [WLDCRD] and blitz for sticking up 4 me, ER3498GTT and NissTrust ur just a couple of experts who were deprived from playing with all the normal kids in the playpen and now try to add ur know it all comments. these turbos were an honest buy and are an honest sell nd the reason 4 their sale is the pursuit for more power. for those guys who were genuinly interested in my sale my apologies go out 2 u my turbos are sold sorry i dont check my posts often otherwise one of u guys would have easily got them but i sold them for $1500 and the buyer is very happy and rings me regualarly telling me the new members to his victims list. thanks guys.

hahahahha seems like every1 is off the road atm, mines been off the road for 5 months and a clear reminder of my slackness appears when i get mail to renew my rego :lol: ahhhh well.

be different, not everyone has these wheels, selling because i am in a hurry for cash. beautiful wheels white centre with chrome dish, 18 X 9.5 al around with 265/35/18 tyres all around. falken tyres hab only done around 4-5000k's. i bought them brand new $900 a wheel straight out of japan, $3600 worth of wheels and $1500 worth of tyres. wheels & tyres near brand new. make your skyline look phat. look at my display picture thats them. these rims were made to suit an r32 gt-r but will fit any skyline because the offset isn't too far out, may have to roll guards. the attached picture is the actual wheels for sale, tyres on the rims at the time aren't the tyres the wheels are selling with. $3500 for wheels and tyres. <<<< <<<<

near new turbos, direct bolt on turbos for rb26 only travelled only 10,000km and never run over 1 bar/15psi. can handle upto 1.5 bar boost/21psi with aftermarket dump pipes, can do with standard but produces too much heat so with standard dumps 1.2 bar max. Comes on boost quick and very aggresive. excellent for street use. no shaft play perfect condition and looks brand new. $1950 o.n.o

Near new white SSR 5 spoke 3 piece wheels, full set of 4 with near new falken tyres, tyres have only travlled 4000km. Chrome dish with white centre. Comes with SSR valve caps aswell . Each wheel cost me $900 and tyres were $1450. $5050 worth or wheels and tyres going for $4000 ono. Urgent sale that is why the price is cheap, email me at [email protected] or sms me on 0401376402. my display pic is my car with those wheels on it.

Near new Zex Nitrous oxide wet system. Complete kit with bottle and all lines $800. Urgent sale, located in Brisbane. Also 4 Sale: *Motec M600 near new condition with complete wiring loom. Will suit any 6 cylinder application, over $4000 worth $3300 ono *Brand new Power FC with controller, suit 32&33 gt-r - $1250 *Brand new Greddy E01 boost controller - $950 intersted in anything? please email me [email protected] or ring/sms on 0401376402.

Greddy Profec E01 Boost controller brand new in a box. selling for cost price $950. Urgent sale, located in Brisbane. Also 4 Sale: *Motec M600 near new condition with complete wiring loom. Will suit any 6 cylinder application, over $4000 worth $3300 ono *Brand new Power FC with controller, suit 32&33 gt-r - $1250 *Zex Nitrous Kit, all lines and bottle - $800 intersted in anything? please email me [email protected] or ring/sms on 0401376402.

Apexi Power FC to suit 32&33 GT-R with hand controller brand new in a box $1250, selling for the price i bought it for. Urgent sale, located in Brisbane. Also 4 Sale: *Motec M600 near new condition with complete wiring loom. Will suit any 6 cylinder application, over $4000 worth $3300 ono *Brand new Greddy E01 boost controller - $950 intersted in anything? please email me [email protected] or ring/sms on 0401376402.

Perfect condition garrett gt2530's never run over 1.1bar boost can handle 1.5bar. on my car for only 19500km. spool fast and come on boost hard prefect for street, capable of leading a gt-r into the low 11 sec bracket. Urgent sale, located in Brisbane. Also 4 Sale: *Motec M600 near new condition with complete wiring loom. Will suit any 6 cylinder application, over $4000 worth $3300 ono *Brand new Power FC with controller, suit 32&33 gt-r - $1350 *Brand new Greddy E01 boost controller - $950 *Zex Nitrous Kit, all line and bottle - $800 *Apexi Intake Kit for RB26 - $250 intersted in anything? please email me [email protected] or ring/sms on 0401376402.

Motec M600 near new condition with complete wiring loom and map sensor. Windows based system a lot more functionable more options, more logging, more outputs and easy to tune. Will suit any 6 or 4 cylinder application, over $4300 worth $3300 ono. Urgent sale, located in Brisbane. Also 4 Sale: *Brand new Power FC with controller - $1250 (selling for cost) *Brand new Greddy E01 boost controller - $950 (selling for cost) *Zex Nitrous Kit, all line and bottle - $800 intersted in anything? please email me [email protected] or ring/sms on 0401376402.