SiR_RB

I can't find any information about rb26 arp L19 head stud torque can anyone confirm what the recommended torque setting is, in either ft lbs or NM thankyou

Il be in the market for a dog box in the next month or so want to see what's out there from now, Either straight cut syncro or helical syncro etc os giken, par etc etc would prefer one that's been refreshed and in a case ready to drop in (transfer case not Realy needed) located sydney but could organise interstate freight to pick up no issues

I've got the same rotors and I contacted brakes direct and gave them the measurements/vehicle and they had them available

Sorry guys just realized Sau is back up and running Number plate bracket sold Nismo exhaust was very quiet will get picks up hopefuly tonorow I been super busy sorry for delay

After a Realy good condition r32 GTR firewall pad inside the engine bay, with clips if possible Pm me please Thanks

Nah it's not that type Il upload pics of everything on Monday

Hks 2.8 stroker N1 block Ported head tomei procams Hypertune plenum - 90mm throttle Hks100mm cooler Precision 7175 1.12 4" dump/mid pipe/cat back Vipec v88 625kw @ 32psi tuned by DVS JEZ

Go the Brian crower ones or the proven supertech singles

My mate has a 6266 gen 2 stock engine bar head studs/springs/cams Made 430kw on 22psi e85 My brother in law with 6466 gen 2, forged 2.6. 264 cams/springs made 560kw at 38psi Both tuned at dvs jez

They will be fine with that duration/lift camshaft

Got some parts spare from my build, *nismo pull type clutch slave cylinder $80 *r32 GTR front number plate bracket $50 *r32 GTR fuel tank with straps, no fuel level sender or lid $100 *tomei boost gauge $60 *sparco mechanical oil pressure gauge with earls braided oil line $80 *nismo gear knob $50 *xforce 3.5" inlet/straight through cannon muffler with 4.5" tip $120 *r32 GTR nismo 3" cat back exhaust, mild steel, has surface rust $200 All parts located in Sydney but can post Can take photos of parts of needed Thanks

Looks good mate

$2500

Thinking of selling my wheels, They are volk racing te37 in 18x9.5 +12 offset all around Originally bronze colour I have them painted in 2 pack gloss black with Red TE37sl stickers I also have the original te37 blue/white stickers aswell Comes with rays red valve stems/caps fitted Asking around $3000 with federal 595rsr all around around 70% tread Can sell with no tyres also Located Sydney

My heads in getting some work done and I'm changing some parts If your starting fresh and need all new shims, what's the quickest way to do so ? I was thinking of putting the buckets in with no shims, measure lobe to bucket clearance then take away clearance needed and this would give you the shim thickness needed ? Would this work or must you put a shim under the bucket before measuring ? Any other ways people have done it and care to share ?

Would a too tight, or too loose belt play a part ? My last belt I suspect was a it too tight Il check it out and try again

I have herd you need to remove it for racing but my mate has same engine and balancer and it revs to the moon and always hitting limiter and never has issues so dunno why mine would through a belt after Afew squirts Annoying

Bumping an old thread I got an ATI 1000hp balancer on my hks 2.8 stroker, had the ac belt come off on the Dyno, put a new belt on and 2 squirts later on the street found my ac belt has flipped upside down on the pulleys Anyone know why? I just cut it off for now as its winter but ultimately I do want a working ac system and that I can drive the car without it always damaging belts Ac tensioner has a new bearing

My mate had -9's stock 34 GTR bottom end, cams, head studs and made 360ish kw at 26psi if I recall Do head studs and keep boosting till there's nothing left Don't think you will go over 26psi with such small rear housings

Sold pending payment

Lol no thanks

I currently have black te37's in 18x9.5 +12 on my r32 GTR that I'm thinking of selling for new wheels Before I look at new wheels I want to see what's out there They have to be black and in good condition, but show me what you got regardless as they can be painted Needs to have dish ! Big GTR width and offset all around Pm me what you have Cheers

Could be back up for sale in the next month or so I will notify al interested parties once it's off the car Thanks

Yeh m pretty sure it is, let me check tomorow and get back to yiu

After a full set of nismo floor mats to suit r32 GTR Either good used condition or new Pm me Thanks