Jump to content
SAU Community

hypergear

Members
 View Profile  See their activity

  • Posts

    4,102

  • Joined

  • Last visited

  • Days Won

    25

  • Feedback

    100%

 Content Type 

Everything posted by hypergear

  1. hypergear
    ^^^ I think you will need to preload the actuator alot more then where it currently is. Was this SS2 built with a black .70 comp housing or a smaller .60 comp housing?
  2. hypergear
    ^^ Using this turbine housing shown on photo above. The GT3076 CHRA will be straggling to perform any thing 250rwkws or above. Which our standard high flow service can easily out perform, and cost you less then half of their listed price.
  3. hypergear
    The intake temp was 14 degrees higher today.
  4. hypergear
    I thought you can't apply corrections on Shoot out mod can you?
  5. hypergear
    Some results sent in. This is a ATR45 SAT version on an Rb25det Neo motored Stagea, Dyno dynamic roller dyno shoot out mod. Final result of 400awkws (red) on a 36 degrees day, against a turbocharger that was previously installed. Unopoened engine, factory cams and cam gears. Usual mods and E85 fuel. Good example of an externally gated setup out of factory exhaust manifold.
  6. hypergear
    The ATR28SS15 would be a perfect turbo for your application. I didn't look into some thing even smaller as it doesn't make that much of a difference in response but did loses quite a lot of power. I've handed drawings of two more sets wheels to be engineered for the GTR. for main time, I've picked up a members R34. Its got 170,000KMs on the clock, average condition, with heaps of ice and minor engine mods done by a 20 year enthusiastic. probably due to the mileage, this engine feels pretty rough compare to my other two skylines. This might be affecting performance on the dyno. Condition of this car probably represents the majority of R34s on roads today. I will be installing commonly seen mods including a Blitz return flows cooler kit. the goal would be around the 330rwkws mark on Pump fuel, internally gated bolton. Will upload dates as project moves along.
  7. hypergear
    I'm uploading my result here. This is a newly developed SAT ATR45 turbocharger. The engine is fully stock, unopened. Using factory cams, and factory cam gears. This is a single turbo, externally gated on E85 fuel. It is pretty good to drive on road. Power n Response against factory twins:
  8. hypergear
    few bits to check on: 3inches or bigger Metal induction pipe with Pod filter. Check pressure drop across intercooler 3inches or larger turbo back exhaust, all flanges has to be in 3inches, Cat has to be in 100 cell, no cat gives the best result. Tension up the actuator rod. Further update. This is the ATR45 SAT version for RB26, I've trailed the ball bearing version, and it have made a very slight increase in response. I'm hitting the MAP limit for the Haltech ecu, will be installing an 3 bars maps sensor shortly. Result against Standard Bush bearing model: Also running against my factory twins:
  9. hypergear
    The adaptronic cost $1150 additional with any turbo purchases.
  10. hypergear
    Hi, The SL20.5 is $900 each to build. That comes in a T3x 10cm turbine, Vband rear.
  11. hypergear
    Check pressure drop across the cooler. I see this happens with certain model of blitz coolers. Also pre-load the actuator abit more. Green is before cooler and the rest is after.
  12. hypergear
    and one more set of data:
  13. hypergear
    -5s are very laggy turbos for RB26. and in lot of cases, the standard "T1.5" turbine manifold gets bored out, which adds more lag. if you are using adjustable cam gears, dial +5 on the inlet and leave 0 on exhaust. That will advance response by roughly 300RPM. Or get HKS V cams with active VCT cam set, that knocks out about 700RPM of lag. Alternatively get -9s or check out our latest single development on our thread.
  14. hypergear
    The 53mm GTRS turbines don't work with RB25det engines very well. The SAT stands for Special application turbocharger. This one is made only for Rb26 and Rb25 turbo engines working with large external gate setups.
  15. hypergear
    Note how the 20G falls over on top end. This is from our re-worked version: SL20.5 mentioned earlier. It is made to have the same down low torque as the 20G, while holding the power band up top. Running against Kando's TD06L2-20G on a standard RB25det motor, Same response, more power with much wider power band. Nothing is changed apart from the turbocharger. Price difference is within $100 to listed kando item.
  16. hypergear
    Assume turbine housing in T3x that suits factory dump pipe. It also need water and oil lines. induction pipe and silicon hose connect to factory cooler piping.
  17. hypergear
    Appears that you looking for results for this type of application. and I actually found one from few years back. This is during the evaluation and development of ATR43SS1PU. Dyno result shown 2535's 53mm turbine in .64 rear working with a older version of SS'2 billet compressor wheel, heat soaks with timing deducted avoiding detonation: for your power level externally gated, you can use our ATR43SS-2 that boltup to most of your factory bits, or the SAT version of ATR45 (result appeared on Rb26) can be made as a bolton for RB25det or a SL2.05 in 10cm turbine.
  18. hypergear
    Free of charge. Before taking it off. have a feel of its shaft play. There should be about 1mm side to side and nothing in and out. If that is the case, check your engine breathers. if you do have a catch can, remove it and let breathers breath into atmosphere and see if the problem goes away.
  19. hypergear
    We can high flow them to -5 or -9 depending on the HP chasing for. With the damaged -7s I need to have a look at the turbo, the smallest billet wheel that I currently make is in 60mm that made 250rwkws on P98 on my SR20det.
  20. hypergear
    GT28 rear is no good for RB25det engine, I don't recommend of fitting a much efficient compressor as it chocks the engine even worse. Since it is still working, sale it and get our standard 21U high flowed unit (we can supply donor turbo if you don't have one). it will make more power with same or better response.
  21. hypergear
    can be done. I can supply a SS-2 comp wheel , that is in 74mm. fitted, balanced with comp housing machined for $450. Alternatively: Balancing $100, Comp housing machining is $150.
  22. hypergear
    When back on the dyno, try a run with external gate screamer un-pluged from the dump pipe or let it externally gated. It will pickup more power on less boost that way.
  23. hypergear
    Yes I can machine the housings to suit. It will cost you $100 per housing to machine. I'm pretty sure their turbine wheels are the same.
  24. hypergear
    I've posted results on different boost levels, so its not necessarily of making more power but much better response and drive ability. When I trailed GT35 with my forged RB25det it stopped making power at 431rwkws at 29psi, This particular turbo will be making the same amount of power except I don't think this engine will take that boost. Goal is responsive 400awkws, this is the best one so far and I'm trailing an updated prototype next week hopping to hit 20psi and 200awkws by 4000rpm. Yes I can high flow GTR turbos with -5 equivalent using our ATR28G1 CHRA or SS15 which probably works out similar to a GTX2867. They are very laggy on RB26 engine tho. For the amount of money I recommending of getting a proper high mount setup and use the new SAT version of ATR45SS.
  25. hypergear
    GTR-R33 Standard unopened engine Brae high mount manifold HyperGear HPVA 50mm external gate 1000cc ID Inejectors Haltech platinum Plug in ECU HyperGear ATR45 Special application Turbocharger 600x300x100mm intercooler 3inches turbo back exhaust 411awkws@26psi E85 fuel. Power and Responds Vs GT3582R on very similar setup:
×
×
  • Create New...