RHiSC

ending tomorrow... going cheap

Putting this up for a mate... its on ebay http://www.ebay.com.au/itm/321077130568 Auction starting at $300. PM me if you want to make a direct offer.

H1 kit $139 - http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...em=200397715175 other types available as well

Exedy hyper triple plate clutch (push-type for RB20/25/26/30 part #NM033SR) Less than 3000kms old, very good condition 80% material left. pics coming soon. $1500 ono Melb pick or can post with courier Aus wide

RB25DET gearbox in very good condition. No crunching, worn synchros or bearing noise. $1400 ono

Kenobi HF100 metal-core cats, 3" in/out and 3.5" in/out. 4" body and heat shield. 100cpsi metal-core highest flowing available. $210 + post for the 3" no flanges $260 + post for the 3" with flanges to suit any Skyline $220 + post for the 3.5" no flanges $290 + post for the 3.5" with flanges to suit any Skyline

putting in a lower ratio will increase your top speed in each gear but will decrease the rate of acceleration if you were doing 100km/h at 3000rpm in 4th with the 4.1, you're going to be doing 117km/h with the 3.5

Brand new stainless steel decat test pipe, to suit all Skyline GTST and GTR models... $90 free post

sold

Just had a quick skim through this thread... wow a lot of different views and opinions. i also wanted to give my 2 cents regarding the Hub vs Roller dyno (eg, Dynapack vs DD) debate based on my experience. firstly this statement - all chassis dynos are designed to give an 'accurate as possible' indication of engine power/torque. with that said, it should be realised that actual engine power is one thing, being able to measure is though a chassis dyno of some sort is another. Other than the actual force applied at the load cell, approximations are used. very clearly the Hub dyno is the winner for consistency and repeatability, although in most cases generally will read 10-15% higher compared to a Roller dyno simply because they do not have to deal with the additional drivetrain losses (wheels/tyres) and friction between the tyre and roller. These figures vary so much from car to car that there is no way to compensate for it, so it is literally ignored on a Hub dyno, with 10-15% being the approximate. Note that i did say 'in most cases' as it is possible for the additional drivetrain and friction losses to be negligible, which is why the software doesn't make its own assumptions. On a Roller dyno, ramping up cars in different gears can sometimes yield different results, but this indicates sometimes large fluctuations in friction/slip at the roller as the tractive effort increases/decreases. A car that also 'climbs' the front roller will usually read a higher figure, as there is less rolling resistence and friction at the tyre as it is no longer riding on the back roller. A Roller dyno relies on consistent strapping/chocking, climbing, tyre pressure, tyre compound, gear selection, etc, to get good accuracy and repeatability - obviously all of these variables are eliminated in a Hub dyno. In summary i can say that Hub dynos DO read 10-15% higher most of the time and can have better consistency/repeatibility compared to Roller dynos, although it is not all that hard for the Roller dyno operator to ensure the same consistency/repeatibility on ANY car if they are paying attention, meaning a lot of the time it comes down to the individual operator/tuner. The more experience a tuner has, the less of an issue this usually becomes. As for this R34 making over 1000hp... completely accurate or not, it should be in the vicinity of 1000hp based on the information in this thread.

price drop to $600

negotiable...

Got a pair of brand new Project Mu SCR (SCRN006) front rotors to suit R32/33/34 GTR with Brembo calipers. West Melbourne $700 pickup or can post

R33 GTST Front Calipers and 296mm rotors in very good condition, minimal wear... in Melb.... $300 for calipers, or $400 with the discs.

n1 water pump brand new in box.... $300

write off

running fine, comp is good just needs a few bits and pieces bolted up and its ready to go.

complete long motor from rocker covers to sump, with inlet and exhaust manifold, fuel rail, and a few other bits and pieces. $1000 pickup only

Any update on this? anybody get a price to do a complete dash?

after a pair of r32 gtst front caliper, must be in good condition..

check pm

i just confirmed... the R34 model does have a different height to suit the Getrag gearbox

it is a pull type so it might fit the late model R32 GTR's and the R33, but it's worth noting that a different part number exists for the R32/33 pull type and the R34 pull type from Nismo... from memory the clutch height on the R34 is quite a bit more than the R32/33...

update - single plate is sold, twin still available. price drop on twin to $800

melb