mattis96

would like this gone asap, anyone interested?

I am negotiable on some parts as i want this stuff gone

hey guys i need some advice on the best way on dividing up the the vacuum hoses for my car. i have the 3 nipples on my intake plennum that i can use, but need to connect about 7 things up. Things to connect are Map sensor for haltech Profec b spec 2 sard fpr wastegate turbosmart blow off valve water meth injection 2 boost gauges (dash and aftermarket) Or does it not matter that much which ones i tee off as they all have the same pressure going through them?

i am cancelling my rb30det project at the moment due to sick family stuff that will be taking up a bit of my spare time now rb30 series 2 head and block, blocke will need to be cleaned before rebuilding and the crankshaft pulley is still on engine and it has only 1 head stud that i was unable to remove due to it being already threaded before i started and i made it worse (all i was going to do was weld a nut to the head bolt and remove it that way but never had the time) $100 rb30 water pump brand new in box $40 rb30 mls head gasket $150 rb30 acl race series mains and big end bearings 20 thou oversize $150 for both Oil crank collar $80 2 rb oil restrictors 1 is 1.5mm, the other is blocked $25 Pick up morayfield also have the complete intake manifold, injectors throttle body if wanted with complete package for free, $50 if seperate Will sell all together for $500

Selling standard parts of my r33 due to upgrading. Hicas Bar $20 RB25 rocker covers $50 2 90 degree fittings for rocker cover ( good for catch can installation ) $20 each Coil pack cover RB25 $25 Turbo heatshield $10 RB25 exhaust manifold $25 RB25 intake plennum and collectors $40 (i think i have new gasket for the intake to collector for free) R33 gtst rear discs and bendix ultimate pads about 80% left $60 RB25det series 1 coil pack harness $25 r33 passenger seat with rail $30 good condition RB25 dump and front pipe $30 Any pictures just ask but its all standard parts, will send to email address only as phone wont mms. All parts pick up unless you pay for postage, located at morayfield. 0406 038 010 if you want to know anything else, prefer text as i do night shift. Thanks, Matt

i also got 1.5mm and the other blocked in 25/30det. might have to change it to 1mm now, thanks for the tips

do you still have the receipt? if so i'll buy it straight away pending its an original.

can people post pics of their 3rd brake light to get an idea on which ones to get, thanks

got one sitting on my engine stand, $100 complete with head,(1 head stud stripped though) am in morayfield, also have parts to go with it for extra if interested, acl race mains and big end bearings, rb30 cometic mls head gasket.

whats an aasa clubman license?

there are a few genuine sards on ebay, you can tell by the price difference which has already been said.

i run eset nod32, no problems, does scans and doesnt slow my system down. also use peerguardian aswell but not sure that helps against much?

how much did that set you back??

i just used pliers to squeeze clamps together then pulled the hose off. although i had trouble with the feed line and ended up replacing it with new line, only because the feed line had no extra slack in it, i think it was about 63cm long so i just got 70cm worth. i just used a big flathead screwdriver and a hammer to get it off The top 2 hoses are return and the bottom one is the feed. Is that what you meant by connector thing? or the wire connector? its just acts like a connecting point with wires both side bracket intank

Bosch belt numbers for rb25det (and probably others) 4pk855 Alternator 4pk915 Air con 3pk855 Power steering

just put a nismo in my 33gtst, very easy, probably took 15 minutes of dicking around just trying to get it back on the cradle though. replaced a bosch 040 that i just couldnt get back on, and i easily spent over an hour on it and gave up. Just put a torch in the tank when you've removed it and you will see how easy it actually is to put on

is it a genuine sard fpr?

double post

what sort of shocks are they? and how much lowered are the springs?

Sorry didn't see it in the description...

I might be interested, is it moulded for the sides in the boot? If it is what side is this for? If it's driver side very interested!

Also keen after seeing how they look on others.

It's been asked but no answer. Rails? Which ones do you use? Could you find suppliers for a gb on then aswell?

While they do fit they are a bit short apparently but still work anyway. The vg30 arp rod bolts as well but require a bit of the top ground off as they are a tad to long. While we are on the topic anyone got half a packet of sr20 bolts they want to sell :-)

Bump for an old thread, which line do you use for the cooler? The one from the steering rack to reservoir? The reservoir to the pump? Thanks