DECIM8

what colour .. take a photo of ur engine as is and then use hue and saturation in photoshop to edit the colour .. then use curves to make it shinny .. presto what it will look like a different colour .. problem is you lose the coloured writing unless your damn good at masking!!

Most likely they'd let me off for the out parkers .. just fix em mate.. oh sorri officer i didnt know they had been out.. If i turned them on when driving they'd fry me .. its stupid and I dont want to imitate a emergency vehicle .. just ghey Im doing it I rekon I can do it from the stalk as its dual stage for parkers and low beams .. so should be able to tap it at the stalk .. I know its possiable on the silvia series .. jap spec has it stock

Just run a light test on it .. u no stick positive in light goes on looks like weve found parkers .. easier than finding it from fuse box .. Should be ok .. I seem to like doing rice wank factor shit haha

DR doof .. u drive a R33? seen u at thornleigh maccas btw

Might drill a second hole in the headlight and run a 3rd line to the headlight and have stock, red and off.. Just an idea .. but yeah suppose its not the smartest concidering that it costs $600 or so a set for R34 lights. And I dont plan to drive around with Red parkers on .. thats stupid .. just for fun

Hey guys, I want red parkers, now while adding different coloured parkers to your car is legal and abides by ADR rules adding Red or blue or white (white at back only) (red at front only) is illegal. So I wanted to wire up a switch to my parkers to switch them on and off on demand to prevent legalities - yes I know not having them on is illegal but seriously will anyone notice? no not really. R34s have tiny faded ones anyway. So would I just go about it hooking up a switch to the cabin and wire a link into the red wire that runs to the parkers? could I do this off the stick/blinker switch? If anyone could help let me know

They look 20 times better .. just buy one +1 for STI

from what ive heard jap spec vrs aus spec .. jap spec goes lower .. aus spec doesnt to keep ride quality or some shit

impul is sheeeeeeeit hot on 34s .. very nice g/l with it

Thats very interesting .. Might design the box for both types of use this time .. swapping depending on music Cheers

Crap I want the Meisters .. -5 is insane tho

Hey guys thanks for the interest... I built the whole setup and tore it out again, the fibreglass I felt was not thick and good enough for the sub, it actually had enough volume to make perfect sound which I was excited about... The sub box is on its second trip to my garage for re-molding.. this time im using the original mold so my car doesnt stink of resin again.. It looked very sexy but a few tips If you do this design make sure you elevate the sub and angle it to point outward.. this will stop shit collecting in the cone.. the subs weight holds the box down and the design stops it moving side ways I also screwed it into the metal struts in the R34 boot... I expect my new design to be finished in the next two weeks. I didnt realise there was so much facination with my design .. just wanted to be different haha oh and have my car alittle more stable in cornering .. now I can do twisties without losing the rear haha.. Will update in the comming weeks Quick note .. spare wheel had to be removed .. the sub needed a 57L sealed enclosure to efficently operate.. 80L ported its a mother of a suB!

but it looks sexi

most people who sell rims will do it .. $100 for all 4 ussually I think ..

well its a fact I am a pimp lol and the covers gave me an extra 100rwkws easy..haha NOT! Took a photo prior to doing door trims (the trims are a mission took me a good 6 hours to do to my standard - Im abit of a perfection freak) when i get my new rims ill get my mate to photograph them with the rims etc.. hes a pro so be alot better.. sorry for quality for pix Ill upload them l8r .. its being queer

would look awesome if you made a board of mdf to cover the wheel wheel bits and covered it in carpet of vynal .. then will look customish nice deign btw.. I installed a amp rack in the same design .. Im trying to do a wheel well sub enclosure .. shit im bad at fibreglass

Thanks alot nismo and the rest of you .. checked the r34 section but the pix arnt close enough.. Ill have to photoshop it for the outline etc but should be fine .. Thanks a million guys

Why dont u anodise the FMIC piping .. its proven to increase heat transfer into atomophere quite abit .. id say 10 fold but im not sure.. Obviously ur piping needs to be aluminum..

$600 for full setup of fake leather including front, rear seats side pannel facia, gear boot, handbrake boot, centre glove box and parcel shelf .. hmm wonder what id chose.. oh wait i did choose it .. custom colours too .. In the group buy sections guys .. But those covers look wicked too!

To remove the metal clips get a table fork put two spikes of the fork behind the metal round thing and gently rock back and fwd to off .. if that doesnt work yank the shit out of them.. As for the glove box dont even worry about doing up the screws for a few ways unless u wack a hair dryer on it now to remove creasing.. it will uncrease in the next 3-4 days u just unscrew the lower part of the lid pop it in and strech as well as u can and screw it up .. For people installing the wall/pannel plates.. heres what I did.. Take all doors, and pannels off.. with a small screw driver dive into the material and work it off the plastic - for r34s there is foam benith which has to be removed(and replaced) with metho and a paper towel (towel worked best i duno why) it will take some nice elbow work to remove it tho! Get some 5mm thick foam (soft type) and some quick grip or upholestry glue for the next steps. With the removed pannels flip them ass up and place them on your material (also ass up) trace pannel onto material and then cut shape out.. do the same for the foam you have aquired however cut it 5mm smaller than the original dimentions on all sides. now glue these together! slide in the material and foam into place and begin gluing the middle and sides of the door, pannel arch the material and slide into the slots and flatten out .. once all the right place use a hair dryer to hold all the shit in place.. then youve got urself new accessories... enjooy! BTW if in sydney PM me if you need foam .. I bought to much .. got about 1.5 x 1.4 meters of the shit

Need the picture of the R34 s .. its different to the R33 and 32 "s's" im getting it embroided on the seat.. cheers guys

When I drive my car (I drive mostly western suburbs and north sydney) Ussually find that people make way for my car, otherwise I use it like a truck does anyway.. Im always letting people in pisses me off to no end when there is clearly heaps of space for them to merge yet they decide to brake n piss around until finally decide to roll into my lane by this time ive launched it and i have to jump on the anchors.. So yeah people drive like dicks in sydney but victoria has to have the worst drivers ever, most are drunk and the road isnt prop setup with signs so people drive all over the place. and dont let you merge, aggressive and then they come to sydney and do 40 in a 60 zone

guess ill do that then .. should be right .. anyone know where to get 5mm thick foam .. the r34's need it to make the door pannel look puffy..

Problems aside.. They are some damn hot rims m8

Well general guide is this 9" wide with +30 offset is a little to wide for the GTT (front wheels mainly) Safe to stick with +35 for fronts (which im doing) and +30 max for rears.. but ussually inside is best especially if your going to drop it. Hope it helps