Jetwreck

how about fluro pink with metallic and pearl + dark purple spec's!....now that would be ga.......sorry cool!...

What makes you think that its an NM35? Doesn't look like the guy was really after performance over stance!

Wheels were made by Cast Alloy in Adelaide(90% sure)......be aware that there are 2 different wheel setups....the 1990 wheels were setup for smaller hubs and lighter......1992 wheels have a larger hub setup and were heavier. You can tell the different wheels fairly easy as I am pretty sure the smaller centre lock's had the Nissan logo on them. I do have access to some genuine set's of wheels, but all of these wheels would have to be crack tested and the price is a little heafty for what they are.....IMO the guy's dreaming if he thinks his going to get what his asking! PM me for further detail if your interested!

Nah I wish....physio....and I did spot your better half last night....I have a problem mentioning her because of the checkers comment....lol

Gold!!!...lol.....

lol!

Hey Cam.....bet his got his hat on the wrong way again! It's his "I'm too tuff for you bitch" look!!!!.....I try not to laugh when I see him like this.....but it's just tooooooo funny!!!

yeh that worked....I'm convinced ....

Nice boat's!!!! Have a great one....what size motor you got on the boat?

Aaron your a dip shit mate!!!! it's not that old POS Camry that the C34 looks like! It's this one!!!!

What's the throttle controlled by!

yup....do it!!!....be a pioneer! might find some others follow once they know it's good!

At oil change as I only have the PVC one atm probably about 100ml's....my motor only has 47,000km's on it too!.....the other side is probably about the same! An no I don't drain em back into the sump....I just collect and clean at service interval's.

I guess it comes down to how your dump flow's!......a good one makes a difference! I noticed an improvement straight away and that was before my tune!

Nice set of slotted DBA rotors and maybe some Nismo Pad's to suit worked great for me before I went the next step!....Pads are a personal preference I liked the Nismo's because I could not get em to fade on the street and they had a great feel.

bit of a messy engine bay but it show's the PCV side....the rocker locations are a little harder to shoot but it runs into the back of the suction pipe.

I think that's what Ian got....you just need to make some brackets to keep em off the wheels on the front....the rears were an Identical fit!

Just rip out all the VCT and put some big f#$k off solid lift cam's in.....the idle would be awesome!!!!!!.....lol!

Ones to stop oil going from the PCV into the intake and the other is to stop the breathers on the rocker's throwing oil through the FMIC. Watch what size you get as there is sweet f#$k all room to fit em in. Couple of pic's for locations.....these are from Cam's car.

C#$K....I bid on em the week before and they went $15 above my bid price......then they went back on and no bid against you at all!!!...I could have bid too...but i didn't think it would go that cheap as I went higher than you did! good luck with em....hope you chassis cracks in half!!!!!! oh great by btw!!!!

I don't but i know someone who does if you interested.....I'll have to check and see if I have a spare Gasket. PM me for further detail

lol....one day you'll get it done!!!! I thought you had an AR-X for some reason!

your calling his car ugly....and you would do a V35 front end swap V35's have always been ugly imo and it doesn't really matter what you do with them!.....V35 are just a poor man's 350Z!!!!

might be up for the next one....just need a shift kit so I can get into 3rd and 4th. As you can see no problems with the 4WD stall and launch.....just the slow shift!!! P.S. Adam...loving your build and work so far