YoungLine

Hey guys im after a Series 2 400r Front bar in melbourne. Preferably of silver colour if possible, otherwise any will do not cracked tho!

Im sellin my 96 N/A 85,000km on the clock 400r kit, exhaust,18's,extractors,whiteline bushes, 5 channel cadence amp 2 12'subs pioneer 6x9's etc wanna upgrade 2 a r34

Hey guys i have suspisions that i have a leak in 1 or more of my injectors. Do u guys know were i can buy O rings and insulators for my standard injectors in my Series 2 R33 N/a I am not to keen on purchasing them from nissan i rekon they r a bit overpirced there, is there anywere else i can get em? also if not is there any recommended injector cleaning place in western subs of melb? thanks

Hey guys im after a o2 Sensor that plugs straight into a N/A r33 series 2. Preferably new. Thanks

Hey guys i encountered another problem yesterday, this 1 more annoying then anything else and id like 2 get it fixed the car began jerking a lot when i ease of the gas n give it less revs... especially wen im on the freeway if i ease of at 100km/h down to 90 it jerks like crazy at low speeds also but not as much still annoying n worries me do u guys have any idea wat i should check first? and its not the BOV cos its a non turbo

HEy guys im after a left hand side Lower Control arm from a R33, i dont kno if it matters but preferably of a series 2 non turbo.

haha im guessing this is the 1.. hehe his selling it for 23,900 I still laugh everytime i c it, the stickers make it go faster 2

Im thinkin bout gettin the same springs mate so tell me how it goes. my skyline is actually sittin on 18's aswell but with stock springs.. it dosent look to good as it looks high and the wheels come no way near the guards, big gap. But the front bar is about 3mm over the gutter wen i park so i jus miss it, so i dont kno if its a good idea 2 lower it any further as id scratch the fk outa the bar.

So my Lower control arm on my passenger side is bent and i wanna replace it. I went and found a lower control arm from a r33 at the wreckers but for sum reason the arm was shorter then the 1 on my car? i have a series 2 non turbo Do arm lengths Vary between s1 and s2 or is the difference because its a gts not a gts-t? need help in finding the right arm.

It was all done at the tyre factory. The car hasnt been in an accident before, and there are no aftermarket parts. Can u guys judge from a pic if the bushes r wrecked cos i took a pic of the left rod. Umm so if it needs changing would it be more beneficial for me 2 just get aftermarket bushes or a set of rods. and how do i go about fixing the rear toe does that require aftermarket parts also or just a decent alignment? ill try getting my car down 2 traction tyres soon just have no money atm

Hey mate i got a 96 silver s2 gts aswell wit a 400r front bar Looks clean as well used 2 anyway got a crack thru it now OUCH deciding wether 2 get a new front bar or 2 fix this 1, grab me a cheap 1 if u can haha

Ive got an annoying problem with my steering wheel turning to the left on its own.. i have searched the forum and the only thing i found is that it can be the wheel alignment, now im not to familiar with wat all those settings mean hoping sum1 can help me. Now my steering rack had a leak in it so i had that replaced and a wheel alignment had been done.. and now the car pulls to the left no matter wat speed im going at wich is very anoying, whats more annoying is it pulls harder when i brake... wen i brake to a full stop the steering wheel can swing 45 degrees to the left on its own, so im constantly driving with my car pulling to the left, can some1 have a look at my allignment settings that i have attached and spot anything wrong cos i dont quiet understand it. Oh and i also had new tyres put on at the same time. thanks

Hey guys im not sure if this is the right section of the forum 2 post But i have just dinted the side of my skyline OUCH :'( I was jus curious 2 c how much it wuld cost 2 fix hoping u guys culd give me an estimate and point me in the direction of a good panel beater (western subs Melb) i havnt been 2 a panel shop b4 so ima bit of a noob. also will it be perfectly straight after or will it be noticible it has been straightened. thanks guys hope it wont cost me 2 much as i just paid for insurance (third party lol).