xris

No sorry was slammed on stockies

FS - R33 GTST Pedders Extreme 8kg 6kg Coilovers $700 I have a set of Coilovers for sale for a R33, low km rrp is $1600 I'm after $700 pickup Melbourne west or can ship for a bit extra

So here ends my dcs clutch. worked with the above 6-8mm of throw for 1 lap then the twin plate sound went away. (and yes i had 8mm of throw on the clutch so it didnt over extend) think i found out why...... lesson to be learnt, use a quality jap brand you can trust.

NPC told me that i need 6mm-8mm throw. my current measurements are 80mm bearing to bell housing and 78mm block to teeth. so thats 2mm travel. i need to reduce my bearing carrier by 6mm. Here are the lengths 30501-A3800 12mm, 30501-N1601 14mm, 30501-U0200 16mm, 30501-S0200 18mm, 30501-B6000 20mm, 30501-S0160 22mm, 30501-K0404 24mm, 30501-K0510 26mm, 30501-N1600 28mm, 30501-N8400 30mm And how to measure it (A)

So going by these part numbers i'll measure the one i have atm and get the one 6mm (or closest) to that size. 30501-A3800 12mm, 30501-N1601 14mm, 30501-U0200 16mm, 30501-S0200 18mm, 30501-B6000 20mm, 30501-S0160 22mm, 30501-K0404 24mm, 30501-K0510 26mm, 30501-N1600 28mm, 30501-N8400 30mm

Ok so ive spoken to Doug at NPC and he asked for the following Bearing Carrier to bellhousing length is 80mm (70mm +10mm for adaptor plate) Clutch from Block to face - 88mm Teeth to clutch is 10mm So we have a throw of 2mm. He told me it needs to have at least 6mm. But suggested i get a bearing carrier 6mm shorter than the one i have atm giving us a throw of 8mm.

Lesson to be learnt from all of this is DO NOT BUY A CLUTCH FROM DCA /Direct Clutch. I ended up sending mine to NPC to asses and let me know what was wrong with it. Apparently the Pressure plate was wrong the teeth were over extending causing the rivets to wear and come loose making it harder to disengage. So i had them fix it for me cost $160 lol. So now engine is out again and im finally going to get this to work (i gave up on it and went a jap clutch threw it in and it worked straight away) but now i want to push some decent power i need the twin plate So they have sent it back and asked me to do the following Measure bearing to bell housing outer currently sitting at - 80mm Then measure ring gear to top of clutch. - 85mm Ive also taken a few other measurements like back of engine to top of clutch/teeth when tightened - 75mm So i'll give the guys at NPC a call today with these details and im sure they will tell me i'll need to buy a new bearing carrier X length so i have X amount of throw for it to work. Will update this thread once i call them and give them the details. And for the person who said are the plates backward LOL no they will only fit one way and then on top of that they have stickers saying to flywheel to pressureplate etc. so yeah ive had this thing apart and back together that many times its retarded. i even swapped it for a rb25 box and the guy also had problems with a stock setup so i knew then it wasnt just my setup causing this so gave the box back and now im here again lol

Cool payment sent this morning. My brothers putting in his now. i'll have a membership card along with (hopefully it turns up by then) my license on the day. Now to wash the dust off the car and get it ready,

Ive got my cams number and ive lodged online for my license. so thats all sorted and paid for. Reading the Entry form and it states - Entry is open to members of affiliated car clubs. Our Club is cams affiliated so is that ok? or does it mean affiliated with SAU?

Coffee machine onsite....im in. also getting my brother to register as well. (im currently sorting out my cams license). So i'll put my application form in and arrange payment and put TBA and bring my receipt from cams if i dont have my license in time?

Hi Guys Selling a set of Stern wheels we have at the workshop that we no longer need. They have tyres (front 215/45/17 camber worn (have moved that to the outside so inner has plenty) and some 50% worn unigrips on the rear 235/45/17) Wheels clear skyline brakes no problem Price reflects condition - $550. Pickup west footscray Vic Phone / SMS 0415693273 Neil

Sold Pending Payment!

Hi Guys Selling my wheels off my 180sx. ive had these for a few years now slight scratches on the rim edge nothing major, cant see from a short distance. Looking for $2000ono including tyres. These are coated in the more expensive Hyper Silver. Originally cost me $2600 (without tyres) The AME TM-02 wheels is produced by Enkei's MAT Technology! Enkei's MAT Technology makes the AME TM-02 wheel stronger, lighter and with less Deflection than most wheels. As seen on the Cyber Evo! Front 18x9 +15, 9.3kg - Nexen N6000 225/40/18 - 90% tred Rear 18x10.5 +22, 9.88kg - Kingforest KF850 235/40/18 - 90% tred Wheels are located in Melbourne (West) Can ship for small fee. or pickup $2000ono PM or SMS 0415693273

so its raining down there for the rest of the week and saturday....i dont feel like putting my daily into a wall so im out..

Check out the Lynch family. i think they like their commodores lol

Been waiting all year for this just got to get the civic ready Reverse figure 8, is the track ran backwards? or you go straight instead of turning left and going down the dipper? have only ran it clockwise

Hi Guys. Bought a Nismo Slave to try resolve an issue with my DSC twin plate. Ended up being the twinplate being too heavy. So no longer need this. Its in near new condition only used for testing. Paid $180-$200. Looking for $150 delivered anywhere in Oz. Or pickup from West footscray. Looks like this PM or sms 0415693273 Thanks Neil

Last time we were at King lake we got stopped by cops, just did breatho's and wrote down all our details. We spoke to some locals and they said the main street gets filled at like 2-3am in the morning with jap cars going up and down the road into town lol so yeh cops know about it. they also watched us until we left town (cops) so yeh just be mindful when you enter town (its a 4x4 mitsu triton ute)

so i tried spacing the pivot ball and this did not help the clutch now goes into gear but still has issues with the wheels turning while the clutch is in. anybody with an idea care to give me a clue?

Nope still didnt fix the throw problem. have full throw of the slave and it still does not disengage this POS clutch. Now i have to go back to spacing out the Pivot ball to bring it 10mm closer again....hopefully without having to remove the gearbox/engine again... but from past experience i may have to. Possibly look at cutting a hole in the side of the box and retigging it back up when its done...

Direct from nissan.

still not working. put the nismo slave back on and it has throw but not enough to disengage....spoke to anthony from maztech and he said this happens all the time with these clutches. FFFSSS! so back on goes the 1-1 slave heavy but hopefully this gives that extra bit of throw i need to push in this bad boy...

Hi Guys. Got the driver side Bride seat rail forsale(suits brix/ergo/euro bottom mounted seats). after $150 pickup. Also selling my Bride Euro II for $600 (red in colour) Pickup from either Taylors Lakes or West Footscray numbers - 0415693273 or PM Thanks Neil

Hi Guys. Im selling the seat out of my 180sx (Driver side) as im upgrading to a bucket. It comes with a R32/A31/R33 rail but fits into a S13 fine (will include a washer to hold down the one leg that isnt long enough). Seat is in really good condition as i hardly drive the car lol. Can be put in as a passenger seat. Im after $800 for the seat including rail or $600 for the seat and $200 for the rail (prefer to sell as 1). PM me or SMS on 0415693273 thanks Neil. Pickup is prefered or buyer to pay shipping. Seat is located in West Footscray.