Jump to content
SAU Community

Craved

Members
 View Profile  See their activity

  • Posts

    17,563

  • Joined

  • Last visited

  • Feedback

    100%

 Content Type 

Everything posted by Craved

  1. Craved
    needs more pics dave
  2. Craved
    read all the other threads about fuel consumption for things to check - handy app though
  3. Craved
    Middle wire on the oxygen sensor
  4. Craved
    im guessing your trial bar is fibreglass - its not going to melt
  5. Craved
    high speed low pressure plenty of cutting oil
  6. Craved
    it isnt actually - looking at the bar there are a few differences in lines accross the bar lower lip is smooth not ridged - angles on the side openings are different wilyawns pic is the right bar
  7. Craved
    i'll look into thet fatz - cheers
  8. Craved
    well under that black knob that spinss............. anyway - there will be a splined threaded bolt that the wiper arm gets fixed to if thats still there, then you just need to find someone wrecking a 32 and get the rear wiper arm and the nut - plus the little cover that goes over the nut too. push it on, tighten up and away you go.
  9. Craved
    atleast it looks to be an LED one and should be relatively light. install it right in the middle at the top, basically you just need some new high strength double sided tape.
  10. Craved
    this one of those crappy compliance 3rd brake lights? i'd take this opportunity to work on a nicer rear 3rd brake light
  11. Craved

    My Photo Diary.

    Craved replied to Sl!m's topic in Photography

    this thread is lazy
  12. Craved
    are you testign the power supply? or they just dont work? start with the basics - remove the lower gear surround - (2 screws behind the ashtray then lift from the gear stick opening) and check the 2 plugs are in place for the lighter - lighter has a light around it, hence the 2 plugs same with the wiper - check its plugged in
  13. Craved
    you shouldnt have any issues as its not an ADR requirement to have it there
  14. Craved
    what opens and closes it? what is on the other end of that cable? r33s run a climate control unit that uses the doors in the heater box to control temps - find it strange that you would block the heater line like a early 80's car does
  15. Craved
    wow thats an old style heater valve - havent seen r33's running one of these before though. think some info regarding your car and motor would make it easier
  16. Craved
    i test fitted a GTR replica bar on mine, sits higher than the stock type M bar
  17. Craved
    will it be taking any weight? if you use your boot then you would need atleast 3mm thick alloy. your best bet normally is not to go to a supplier for smaller portions, but to a sheetmetal shop and get them to supply we do sheetmetal in my shop also, so with a template we can cutout what you need (after tuesday due to the long weekend though)
  18. Craved
    I'll give you a buzz on monday
  19. Craved
    hahaha gonna make me drive down again are we lol pm a price for each i suppose
  20. Craved
    draw a diagram of what you have tried.. since from a normally -ve switch system you connect a test light to it, it will light up when you earth the earth switch trigger wire to earth as it completes the circuit
  21. Craved
    cheers for the door - you got a price for the chassis loom?
  22. Craved
    the door switch should be activating an earth on the chassis - so you would connect the earth from your new lights to the switch in the door jam.
  23. Craved
    they fit the R34's so should fit 33's without any issue
  24. Craved

    Cad Files

    Craved replied to crack's topic in Fabrication

    what are you going to charge for the rb26 inlet manifold flange you have there?
  25. Craved
    unless you can hammer weld or are good with a shrinking disk you should use the tack method for the panels. Bear in mind that quickly cooling the area after the weld will cause it to shrink, you just need to be sure that the shrinking effect isnt greater than the expansion caused by the welding.
×
×
  • Create New...