Jump to content
SAU Community

Craved

Members
 View Profile  See their activity

  • Posts

    17,563

  • Joined

  • Last visited

  • Feedback

    100%

 Content Type 

Everything posted by Craved

  1. Craved
    its a nice flashy light - but STOICH on those are about 11:1 it wont show lean unless there is a huge drop in fuel supply - since 11:1 on most turbo cars will already be in trouble.
  2. Craved

    My Photo Diary.

    Craved replied to Sl!m's topic in Photography

    mmm fluro green water
  3. Craved
    lol i get it hahahaha causing quite the fuss
  4. Craved
    90 deg isnt hot though - system is under pressure which raises the boiling point - lotus elises run at 110 degrees std operating temp. my 25 is running a std nissan thermo with a 40mm PWR radiator and it sits at 89 all day everyday confirmed on autometer guage in the top hose, think the gasket issue might be something different again.
  5. Craved
    one by me only just starting out - thanks to slim for teaching me stuff about the camera lol
  6. Craved
    AAC - auxilery air control - back of the plenum near the pipe to the brake booster . do a search for ACC valve
  7. Craved
    hits the inside of the car? i would be looking at cleaning the AFM and replacing teh plugs ... then get a mechanic to check your engine mounts.
  8. Craved
    hey Neil, FMS has sold it to me but that was a while ago - did you check the link i posted earlier? think i might start making up some sheeting someday soon, was waiting on confirmation of the best UV stable resin to use on it.
  9. Craved
    lol - removing the turbo doesnt change the model of the car - they can still get you for driving a turbo car ..
  10. Craved
    nice project - looks like you havent done the seem welding bit yet - dont do too much work around that area until you get the welding done as most of the filler near there will be ruined with the welding. try to wire brush all the scorching around your welds too before hitting with filler helps keep as little contamination between the filler and the metal.
  11. Craved
    closest your gonna get lol
  12. Craved
    do the same with the can - so it sort of splutters onto the part dust coatings only - but try to make sure its a hot day/room
  13. Craved
    use wrinkle paint - then coat over it in the colour you need. OR you get a spray gun full of primer , turn up the pressure and pull the part back from gun - so it dries as it heads for the part - then the primer will be wrinkled - then paint it!
  14. Craved
    old term for the doors interior trim - back when the trims where a flat "card" of board covered in material.
  15. Craved
    nissan consult can be used from teh cabin if you ca get a hold of it check for error codes from the std ECU - search without knowing how the popper on teh bonnet is hooked up, its hard to suggest anything other than try to get power to it manually.
  16. Craved
    your lucky - mine wont last 3 days with my tracker. i spent 2 days at an auto electrician like you - one thing i found was a 1.3A draw from the turbo timer with everything off - pulled it out and never put one back in. without the current draw numbers its hard to tell if its bad or not - from memory a normal standard car should only drain about 1 to 1.5 A when sitting
  17. Craved
    good walk through - thanks for sharing. just be sure to take into account the additional material thickness for fitment when replacing the parts.
  18. Craved
    ive seen those magnetic ones - but only for skis and fishing rods, are there any out there wide enough for boards. need some also since the daily's back seat dont fold down
  19. Craved
    if its as thin as it looks, i would reinforce the back of it with some new fibreglass from a DIY kit from bunnings or something. also chip that flake off before you start anything as well, dont want it getting worse under new bog etc.
  20. Craved
    looks good daniel - a clear coat would really bring out the colour and flakes.
  21. Craved
    about $200 for a full 5 piece cover set
  22. Craved
    that is realllyyyy nice maybe find out the builders name - they will advertise which paint they used - maybe not colour but brand atleast.
  23. Craved
    im sure i saw a pic in here of a wrinkle purple RB26 - anyone know the motor im talking about?
  24. Craved
    rb25 headstuds torque process
  25. Craved
    Paint with pearl red flakes over black base --- i used WAY too much red flake in the clear - tone it back and it should work like you think - but it will always look a little red
×
×
  • Create New...