JamesK

So if a new IBC is around 300-400, and an AVCR is aorund 700-800 (just quick price look up) WHAT THE HELL ARE YOU PAYING FOR FOR AN AVCR?...is it made of gold???

Holy crap....thanks for the link abu, I just took my baby to Trent the other day...if I cant trust my own tuner who can I trust??? lol, Well I guess since PFC Boost Control and AVCR use the same solenoid AVCR is obviously out of the questoin....greattt... now I have to get a boost controller....another thing to put on my dash... EDIT: Anyone know where to get Gizzmo IBC or a Profec for a decent price?

Not to hijack or anything but its a good thing I read this thread first basically I'm on the market for one as well just got myself a PFC so I was just planning to get Apexi's PFC Boost Controller for convenience sake and i don't want another doo hickey on my dash, but because that uses the same solenoid as the AVCR I'm guessing that one is shit too? Appreciate any advice guys..... P.S. @Hamish...When is this Buller thing going through man???...Anyone up for duck meet next week?

Looking for Antenna Unit Rear Garnish/Fascia (Skyline Lettering between your lights) Seat Belt Retractor

I feel bad for the two 32's but I'm glad no one was hurt, let us know how much damage was done when you find out!

I have a large Burton board roller back to carry all my gear, do you think the soft racks can support that weight? What are they made out of exactly and how do they work?

I got one for me R33, Hit me up if your still need one

Damn forgot to hotlink: http://led.linear1.org/led.wiz

I'm actually looking fro some removable ones for my R33 if there are any available I need them to hold my Snowboard, as it wont fit in the trunk, when I go up for the season anyone know if this is possible?

Skyline Light Up Tutorial Doing this is at your OWN risk I take no responsibility for any damage or accidents which may occur throughout this tutorial, if you're unsure ASK, if you don't think you can do it DON'T What You Will Need: Dermal Tool (Rotary Tool) Heavy Duty Dermal Cut Off Wheel Dermal Sanding Band* Rocker Switch* : If you want to turn it off and on ~ 14 High Intensity LED's ~$60+ from Jaycar or ~$20 from eBay, Check the light output rating ~6-14 Resistors: Pennies at Jaycar, You can use one resistor per LED or for every 2 (But if one burns out so will the other) Use THIS website to calculate the ohm's required for your array Sheet of Experimenters Board: Try to get one that is long enough for the whole thing so you dont have to go through the hassel of putting them together Some Wires: Try to get different colors for convince sake Can of Paint: Match your color code (Recommend Autobarn Moorabbin, they can mix you up a can specific to your car and it's really useful for touch ups Can of Lacquer*: Technically this isn't a must but it provides a nice shine & seal, also gives your that smooth feeling you have on your car Painters Tape Exacto Knife Alright we first start with your Skyline Garnish after taking it off of your car inspect i and make sure it's all nice and clean, you will notice some faded paint on the letters start by sanding them off to get the best light through Start by cutting the tabs off the back Now cut the entire plastic backing out, enough to expose all the letters; For my next project I'm going to try to cut a small hole instead and slide the entire board in but it's up to you This is what your Garnish should look like when you're finished You can sand down the edges if you really want to but in reality no one is going to see the back it's only for your own satisfaction Place painters tape across the lettering and run your fingers along the outside of the lettering it should tear the tape allowing you to just cover the individual letters After cleaning the Garnish again prep your area for painting (preferably outside) apply several even coats of paint (I did 5 if I recall correctly but it's based on how happy you are with it) allow at least 20 minutes between each coat (maybe less or more depending on the weather) *REMOVE THE PAINTERS TAPE OFF THE LETTERING BEFORE APPLYING LACQUER* I forgot to remove the tape before applying the Lacquer which was a pretty stupid mistake and it ruins the finish, not by a lot but it's a lot of work to fix. After you completed your final coat allow drying for a few hours before applying Lacquer; this will seal the paint and give it a nice Glossy finish Admire your handy work before starting the hard bit Cut down your Experimenters board down to size measuring it up to the hole you cut in the Garnish I know this was an extremely crap soldering job; Solder all your LED's, Resistors and your wiring onto the board Finally hook up the garnish to your car wiring in the rocker switch if you want to be able to turn it on and off, as a precaution I wired this to my ACC wire so it can only turn on while the key is in

Crap Completely forgot walk through will be up in the next 20 mins

PM Sent

UGH FINE!! I'll search through my HDD's for the video to be honest I just haven't been stuffed to getting around to it but I'll do it right after exams...somewhat promise

I'll be there Hey Jezzi boii I've seen you at a few of the meets if your near by I'll give you a ride

Warning: This car might be better than sex Saw this walking home from uni (Monash Caulfield) dont know the name of the road I walk everyday but it's straight under the bridge from the roundabout in the uni....things i would do just to sit in it I don't know if it's real but if it's not the guy really pulled out all the stops to make a replica Shelby GT500 Super Snake IT'S HOT!

If a cars in good nick you have nothing to worry about for an RWC only reason I can see he'd be so hesitant is he knows the mechanic is going to find something so he's pushing for a quick sale, I was going to buy a car for cheap and a guy was pushing for a quick sale as well. By suspicion got the best of me and I got it checked out by StateRoads set me back $260 but saved me from a HUGE investment the inspector said the car was so bad he refused to drive it to test it, it's been in multiple crashes and not one panel of the body work had the same paint depth (it's be resprayed many many times) It's a post here somewhere if you haven't seen it yet

Check out this topic: http://www.skylinesaustralia.com/forums/Do...html&hl=Don for State Roads

I can do a menu rip although because it's not a 1:1 copy it's impossible to have a the scene selection page bring you to the right part of the movie Is it me or has every just become your "buddy" htial? hahah

Hey htial you live near me dont you? I can do the rips on my laptop and burn em for peeps but otherwise use DVD Region + CSS Free (PM me for a copy) it will remove your Region lock on your computer. If you just want to play the DVD on your computer use VLC (It's a free open source practically a "Screw it, i'll play anything" video player, When i get a copy I'll upload a rip

*Sighs cant make it guys mother is arriving in the morning succks

Heeeckkk yess!!! umm but when is this? today?? EDIT: Stupid emails dont show sub titles...one day notice? Hahah I'll be there non the less

There is guys, trust me I was in the same boat as you guys but it only comes on when your needle is ON E like basically the light is REFUEL NOW!...haha but in the manual it says there is 7 or so lts left in the tank and even when your start to get at that level it will still start to fade on and off until I think about 5lt

...I assume your talking to me? I just bought one dude

Yea I was thinking about that hamish just wanted to do it myself just to do a bit of learning but I'll prob bringing to Johnny when I have a time

Will most likely be there Jezza Boii: Stealing my job huh? hahah