Silhouette-R

Sent you a PM on the 31 Club.

Hey Fatz, do you happen have a known working AAC Valve laying around?

Would you be interested in removing the AAC Valve from the plenum at all?

I'm running 25DE pistons that have been shaved, also had the block shaved and the head leveled I think from memory. When it was all said and done the compression ratio was over 12:1 which is so border line having to run race fuel (something higher than 98 - 100 octane at least anyway) that on a hot day here in Australia it would ping. I now run a 1.8mm steel multi layer drag style head gasket which has brought the compression just under 12:1. I have spent almost 9 months in Dubai and it's not just hot, it's F**KING HOT!!! So here are a few little things that I see that might be a drama from the time that I have owned my 26/30, the carbs while they would make any RB lover moist in the crutch hearing them at 8000rpm+ probably aren't going to work very well with the humidity and the temperature that is in Dubai even when it get's 'cold' (less hot), you will also need someone that knows how to tune carbs and knows skyline motors well, because if something goes wrong it's going to go wrong in a big way, believe me and it gets expensive after a while. Not trying to put a downer on anything, all the power to you for making a wicked N/a motor, I just don't think it's going to work very well where you are unfortunately.

Sweet, sounds like a few people. Have you heard of any meets that happen in town at all?

Just wandering how many of us are in Katherine, not too sure if there was a thread already created. Is it possible to get this stickied like the Darwin thread? Also spotted a Black R34 GT-R with VIC plates kicking around in Katherine too, is it anyone here? I'm in the Red/Black R31 if anyone is out an about.

Good work Greg, sounds a lot smoother at idle than mine lol What was your reasoning behind the short ram tubes?

How is it coming along Greg?

Just drove past a silver R35 GT-R in South Windsor with the plates LOCKON.

What's the intake setup cost you so far? I'm looking forward to seeing mine finished haha

Dude it's looking super sweet!! I'm going to put down 185rwkw Can't wait to get my cam regrind down. Once you have your dyno sheet can you post it up so it'll give me a good idea of what cams (reassure myself of my cam choice) im going to drop in.

Dude get this on the ground already so we can go cruising like in the old days and hold up traffic for ages hahaha

Well it's been a loooooooooooooooong time since I've done anything in here. At the moment this is the list of modifications: What it has: Adaptronic ECU 1 Bar Haltech Map Sensor Nismo Pressure Plate Chromoly Flywheel Cushioned Button Clutch Series 2 R33 GT-R Head Camtech Cams 290 degree (seat to seat), 263 degree (50 thou), 11.5mm lift - Biggest for RB26 from Camtech Adjustable Cam Gears Supertech Valve springs Supertech Valve Stem Seals Bosch 440cc Injectors Nitto Intake and Exhaust Gaskets Nitto 1.8mm Head Gasket Head Stud Kit for RB30DE/T setup Running very close to 12:1 compression RB25DE Pistons (slightly shaved) Mahle Motorsport Ring Set Balanced Rods Oil Restrictors ACL Race Main Bearings ACL Race Big End Bearings Crank has been grub screwed Crankshaft oil pump drive collar R33 GTS-T Oil Pump R32 GT-R Water Pump Ross Tuffbond Harmonic Balancer Lewis Engines Race Sump 7.5lts Gated Splitfire Coilpacks Rebuilt HR31 GTS-X radiator Head to Sump oil/air separator Tuned Equal Length Hurricane Extractors 2.5" Mandrel Bent Exhaust 3" Stainless Steel Cat Hotdog Mega flow rear muffler (straight through style). 4.11 mini-spool diff Current power output has dropped off to around 144rwkw, but I'm saving for a cam regrind which will hopefully push the power back up and make some useable power down low again

This one doesn't have the torque curve on it but it sits almost flat from 2000 to about 6000rpm at around 350Nm.