Jump to content
SAU Community

fmlycar

Members
 View Profile  See their activity

  • Posts

    586

  • Joined

  • Last visited

  • Feedback

    0%

 Content Type 

Everything posted by fmlycar

  1. fmlycar
    It's not staying on, it usually never comes on
  2. fmlycar
    One of the rear abs rings (passenger side) has a crack through it. Would that make a difference? I put it in gear while it was off the ground and it has drive to the front left, but I can stop it with my hand
  3. fmlycar
    Ok thanks. I'll have a look and a thorough clean in there too
  4. fmlycar
    How can I confirm this?
  5. fmlycar
    Attesa not working I have a S1 C34 that is manual converted, with power fc. I have the secret squirrel mod done. It previously had an extreme TSC that I removed thinking that may be the cause, but no change. My AWD has never worked since I bought the car 2 years ago. When I purchased the car the owner said the Attesa needed to be bled since the gearbox had been out. I bled the Attesa and it still doesn't work. I can hear the pump prime when I turn ign on and it runs occasionally while sitting at idle. I have had the awd and abs lights come on and stay on after sitting idle for long periods. I don't seem to have any fault codes to try and work out why it doesn't work. I have checked that the Attesa ECU is receiving a TPS signal and that is all ok. I'd really like to get it working, as it is hard getting the power down just through the rear wheels. I've been reading and am thinking either pressure switch or accumulator. Is there any way to check these for sure?
  6. fmlycar
    All sorted. Fitted a 10k 1/2w resistor as a pull up from 12v and now it all works perfectly
  7. fmlycar
    As soon as I remove the wire for the shift light the tach works again.
  8. fmlycar
    I have a S1 C34 which is run by an r34 gtt power fc. I'm trying to install a gizzmo shift light, but when I splice into the tach drive signal (pin 5) I loose my tach all together, but the shift light receives the signal, as I have set a shift point and used the hand controller to confirm light is displayed at correct rpm. Is the any way I can receive a tach signal and still have the factory tach in the dash to continue to work? Or is there another wire I can tap into that will work? Or do I need to use a pull up resistor to amplify the signal?
  9. fmlycar
    I'd be looking for a new tuner. Someone who can confidently tune your ecu and not have it knock.
  10. fmlycar
    I like this a lot!
  11. fmlycar
    Ok, so I have correct tps at attesa ecu. What's next? I can get the pump to run for approx 5 or so seconds with the bleed plug in the kick panel disconnected. However, it doesn't prime when ign is switched on. Could it be a faulty accumulator?
  12. fmlycar
    Interior dash clock?
  13. fmlycar
    Sold
  14. fmlycar
    Bump
  15. fmlycar
    Need to sell, no longer required
  16. fmlycar
    Sold
  17. fmlycar
    Bump
  18. fmlycar
    I sold a 6262 something like 2 or more years ago...... Are you sure you have the right person?
  19. fmlycar
    R33 GTR power fc and hand controller Great condition $650 Inc postage
  20. fmlycar
    Ran a new PB for the wagon on Saturday 60ft 2.149, 1/8th 8.736@86mph 1/4 13.33@107mph still rwd. Need the awd working and see if I can shave some time off the 60ft
  21. fmlycar
    That all seems to be ok. Peter from techedge has been trying to walk me through it via email. Should get it sorted hopefully. I may have been a little too eager to hook it up to my laptop, and now have to be walked through the set up process
  22. fmlycar
    bump
  23. fmlycar
    Tech edge install Anyone have any experience installing a 2c0b Wideband with LX1 Display and I cannot get it to communicate with my laptop. I am using a digitus usb serial convertor (works fine with my datalogit) and have checked drivers and comm port and is showing up as comm4. I keep getting timeout errors and a PIM error on the device itself. LX1 Display is showing nD I think regardless of with position is selected (0,1,2,3). I have the lsu 4.9 sensor and the correct htx file saved to the desktop if I need it. But I cannot seem to get any of it to work. My computer knowledge is limited hence why I purchased a complete unit. Any help is appreciated. I spent hours last night trying to work it out. I tried re-flashing the unit and is came up complete without any retries, but I'm still not having any luck.
  24. fmlycar
    bump
  25. fmlycar
    Daytona sensors Wego iv single channel wideband sensor kit. Comes complete with cables, cd, sensor, Unit with built in digital display. Approx 12 months old. Has done 6000km. Also comes with modified knock sensor with 3.5mm stereo headphone jack output. Just need headphone amp and headphones and your set up to road tune. $450 Inc postage
×
×
  • Create New...