Kinkstaah

I don't know the characteristics of that wire, seems to be an issue with conversions (as an OEM RB25 car ostensibly has it wired to the dash). Plenty of "My alternator not charging, turns out it was the bulb in the dash that did it? weird" threads. Try the resistor and give it a go? I don't have a RB25 anymore so I can't comment further!

Going by google and SAU results, this is the wire that goes to the dash bulb. Your car says it is a 240SX. See this thread: http://forums.240sxone.com/showthread.php?t=8702

It may be the alternator trigger wire? Given you've already replaced the alternator... I only found out all about trigger wires (or the alternator exciter wire) when I was troubleshooting the exact opposite of this - My alternator always being on. When the car was off!

So all's well that ends well, yes? I had my VASS Cert and Eng Cert and had a legal V8 Skyline. I shall sum up the things that went wrong between then and, well, now. First of all, the aircon compressor shat itself and had to be fixed. The fix was quite simply a new AC compressor which set me back about $1800 all told given the labor to install, gas, etc. Turns out "Hey man that AC compressor could have absolutely blown its seals/dried out if it was sitting on a junkyard motor for years" is pretty sensible advice. So hey, maybe the power steering is next to go..... I also noticed that while tuning the car (and on the dyno) that my VE map seemed a little richer than most, but I wasn't exactly making more power than most, less actually but I couldn't find where I had got a correction wrong in order to figure out what was going on. I finally got my wideband to talk to HPTuners, and noticed what was recorded in HPTuners didn't agree with the gauge (the gauge showed a leaner value which is what I had been tuning against.) Innovate also have their own app which shows the AFR on a serial line, seperate to what the wideband controller sends to the gauge which is a 0-5v output based on the reading of it, where the Serial line is unfiltered or unconverted. The Innovate software agreed with HPTuners, which was also positive. I read online that people fixed this by putting a voltage offset in the software for the controller to fix the gauge, and it was caused by grounding the gauge to something different to the wideband generally. However in my case it was the same ground, because my gauge literally plugs into the wideband controller and has no seperate ground to even take... I asked Innovate about this because who wants to tune a car with the AFR values out? But go no reply once I told them it was literally plugged into the controller.... Anyway before: And after: (i.e running an offset to the gauge) Obviously then I had to retune the whole car, because it was too rich everywhere. But I enjoy that shit. Strangely, my original battery lasted 18 months on concrete but finally didn't seem to hold charge, so I replaced the battery. I then noticed this new battery also didn't seem to hold charge which made me forgive my original battery that I had since thrown away. Some sleuthing later I found this (with car off) Cool. I also found that an ODB2 Dongle (like say, my HPTuners MVPI2) is not intended to be left plugged in all the time because it will flatten your battery. However the above picture wasn't that. I eventually traced it to the... horn... fuse? After many days thinking and "Surely it can't be the horn, it's got to be something else" I took the car for a drive with the horn fuse taken out, only to notice (Thanks awesome head unit btw!) that my battery voltage was apparently 10.8 Volts. While driving around. Driving around fine, by the way, apparently LS's can just drive around and start at under 11 volts and you'd never know. I jumped out of the car and used my multimeter to check the battery and yep, 10.8 volts with the car running, so it wasn't just the head unit. I put the fuse back in to the horn and suddenly 13.9v. So my horn was wired into my Alternator. I then vaguely remembered something being said about VY vs VZ alternators and exciter wires and maybe the loom I had was for the type of alternator I did not have? or something along those lines... In any case, surgery happened this was wired into the ignition, and now no more flatto batto. So even though my accusump wasn't installed yet (I didn't want to have to explain it to the engineer) its TIME TO HIT THE TRACK. Accomodation booked, track day booked, Winton test and tune, today is finally the day, until the car cuts out. And it keeps cutting out, blowing the main ECU fuse, and taking all my gauges with it. The day before. After being entirely fine for thousands of kilometers and tests. I finish work for theday, run home, say "I have 3 hours to fix this/find this" because Winton is a 3 hour drive away and have to check in at the Airbnb at a non-insane hour. Rewire all the gauges in the car, center console entirely disassembled. No problems found. GF brings pizza to save time while I tinker with stuff. Eventually unable to find. Have to give up. f**k this stupid Skyline Take this car instead: It handles the drive to Winton fine. It does 76 hotlaps on the track day itself fine, over 5000rpm the entire day, hard braking every turn. It was 1s off the pace of the 34 (in my noobie hands) before the conversion. It drives for hours enjoying country victorian sights the day after fine, it drives home fine. (you should buy it) I realise later it was done on OEM suspension too. It sets the bar very high for "You must be pretty f**king good to drive, Skyline, or you're going in the f**king bin) I get home, look for wiring anywhere else it could possibly be and find this: Ahhhhh. My wideband was uh, a bit melty on the exhaust. Fixed the exposed wire, re-routed it behind heat shielding, and problem has not re-occurred, and checked a few times since. Ready for the (next?) Trackday!

Yep usually a decent dyno operator will key in the diff ratio of the car on the dyno, the screenshot you've used.... doesn't... for reasons unknown. 1600 would/should be 6576rpm if that car had a diff ratio of 4.11. Reading the output of either dyno should be very similar once that's taken into account.

I had a R34 GT NA+T initially and went through this. You have the same rear end (stub axles included) as a S15. Your suspension for a R34 GT Non-Turbo is the same as a R33 GTST

Keep in mind the GT has a S15 rear end, so if you do get a diff, you want one that suits a S15. In regards to Nismo, I kept digging - It seems the one I have is a 1.5 way, but acts like a 2 way. This is because when people say "1.5 way" Nismo diffs they actually mean the Nismo 1 way diff. Or you could get a S15 Helical. General consensus is stay away from Viscous, and you'd have a hard time finding one for a S15 anyway.

They also do a 400 cell one. I can smell fuel with 2x100 cells. I can still smell fuel with 2x100 cells and 2x400 cells. But the 400's make a noticable difference. Most people seem to be pretty happy with the 100's though!

It was really really helpful that I had the actual car on the dyno which shows a real time output of pollution (which is kinda cool, and tbh critical for this kind of thing). I ended up raising the idle and playing with ignition timing to effectively make the car idle smoother. Smoother, less choppy, more complete burn, more better-er. The initial result was something like 0.72g/km (triple the limit) and watching the data showed it was only the portions of the test spent idling that was causing any issue at all.

Warning: Much Text So at this stage my engine bay looked like this! Stock as, officer! Way back when I started this adventure, I looked into all the VSI 14 documentation as well as what was advised on the Vicroads's website in regards to engine changes. I attached the PDF from the website on the 25th of July 2019, EngineChange 25-07-2019.pdf but the relevant snip is below. A signed declaration from the registered operator you say... OR a VASS instead, and VASS Certified vehicles need no inspection... I actually called Vicroads to confirm this prior to starting, and took the name of the person (and their supervisor) that this was indeed the state of things. So I went to vicroads with my signed declaration, a printout of the website, the records of the calls I made (prior to starting, like a good citizen) as well as VSI information to prove that my modifications were less than the requirements of that document (i.e less severe) and should therefore be a good candidate for 'equivalent in power, mass and emissions standard' and can be installed without any structural modifications. I also had the emissions standards printed out, and lo and behold the LS1 is more EPA friendly than the RB, RB engines were never sold in Australia, so paying $4000 for a standard RB25Neo for a very cheap sedan is not practical when there's commodores everywhere, right? It should be noted that these terms used in the document on the vicroads website were not defined anywhere, at all, in any form. I went to Vicroads with this information and oh boy did I ruin someone's day showing up with this, because they were utterly caught out by this loophole and had no ground to stand on to reject it. In the end after talking to maybe 3-4 supervisors I had them all agree that while I met all the requirements for having the engine change pass, according to their website, they just flat out refused to do it "just because". I got all of their names down and for the sake of "All Vicroads should be the same" I went to another Vicroads, with the same information. However my experience at the 2nd Vicroads was very different, whereas they actually took the information they provided and effectively passed the car. Their attitude was "Well this doesn't seem like its normal, but all the numbers and documentation match up, make sense, and have been provided, so OK" Except when he went to hit "save" on the record, he found that the car's information had been locked by the first Vicroads Supervisor on Supervisor on Supervisor on Supervisor. I got names and details of everyone involved a second time, and decided to 'enquire' as to this discrepancy and all the time and effort I went through following their rules, attempting to do the right thing, given I also had records of calling before I started anything, and asked for a definition, again. The long and short of it from there, was again through many emails, the tone changed from "You're right, but no" to start talking about different rules all of a sudden and it would need a VASS. I went to take another screenshot of the Vicroads website, which had been updated as a direct result of my attempt to get this change through and the car registered. EngineChange 26-07-2019.pdf Again, snip below: TLDR: They changed the rules from 3 ways to swap an engine, to 2. Consolidating what used to be Option 1 and 2, and making a new "Change of engine scenario two" which basically says if its not OEM it needs VASS. I noticed this when they started referring to "Option 3" initially then started exclusively referring to "Option 2" in the same chain of emails. I thought about taking it to the Ombudsman because it was so very clear they changed the rules specifically due to me, who was following their rules prior to it and just didn't want to pass it to close a loophole they clearly didn't like because... performance car? Who knows... But then thought technically this would just be for the engine details anyway. There's kinda other things that would be covered by VASS codes I wanted to pass (Suspension, Gearbox, Brakes, etc) Luckily, before I turned a tool I also looked into what the VASS Engineers have to sign against, in my case NCOP3, 4, 5 attached as below (Engine, Transmission, Brakes) NCOP3_Section_LA_Engine_01jan2011_v3.pdf NCOP4_Section_LB_Tranmission_V2.0_01Jan_2011.pdf NCOP5_Section_LG_Brakes_V2_01Jan2011.pdf I was curious about suspension but it never applied. My Suspension passed a general RWC and the requirements for it which always boggled me when people never got RWC's for coilovers. The rules are obvious and easy to verify/test against. All of the NCOP for suspension is way beyond the scope of a set of coils. However given my car was now literally flagged by Vicroads I didn't want to take the risk of driving it anywhere. I consulted my new friend who did the weighing of the car for me as he is also a VASS engineering consultant. Effectively you bring the car to him, and he will Liase with the VASS people for you, or make changes to your car to make it pass. Luckily for me as I knew what the requirements were, the only thing he actually had to change was the mounting of 1 coilpack by bending a bracket 3mm. The dodgy speedo WOULD pass (it read from 40kmh.. and the test was at 40kmh but he knew the VASS certifier would definitely 'not like it') so this is where I got the Dakota box instead of the Jaycar literal piece of shit. There was however, one problem. Emissions. In code LA1 you have to prove that the emissions of the car have to be the same as the car the engine originally came out of. ECU's are outright banned. Not a problem, factory ECU. All emissions equipment (evap canisters etc must work) No problem, factory ECU/Factory devices. Fuel injectors must be OEM. No problem, factory injectors. Extractors/Manifolds are considered an emissions device. My stock airbox is stock for a RB25, not a LS1. f**k. Victoria (and NSW) mandate an IM240 emissions test in a scenario like this where things can still pass (i.e ECU no, Injectors also no, etc). Other, sensible states use an equivalency law (i.e a VASS engineer saying 'yeah she'll be right) OR the five gas test/idle test which is MUCH more relaxed. VIC and NSW require an IM240 which is what OEM Manufacturers must pass to sell cars in Australia. To boot, there were no IM240 testers in victoria since McLeod closed. A company called ABMARC have a contract with Deakin University to rent out their Vehicle test lab to do an IM240 test. This costs ~$2000. There are no refunds if you fail. You have to book 3 months in advance. Which is why no-one in VIC is getting full EPA's - The government cannot reasonably supply a test to confirm it. NSW however, do have a testing lab. I called them, and their IM240 testing facility meets the requirements for VASS - which are outlined. The test in NSW also costs $0. They needed to know a day in advance. I called and booked 2 appointments back to back, incase I got very close and could maybe change something? They were more than happy and awesome on the phone to deal with. So... off I went to satisfy the requirements for Vic law, I ended up doing to do a test.... outside of Victoria... to the "NSWroads" facility in Botany, Sydney. Armed with 4 cat converters and a laptop you best believe I f**king did a lot of road tuning up there for stop start conditions! Also, my car managed to get pretty reasonable fuel economy (better than a VY SS claimed figure..) This was also when I found out that my Aircon compressor absolutely shit itself so I had a nice 20 hour drive ahead of me with no Aircon. This later cost me about ~1500 to fix with a new compressor, new gas, and all that labor to get to the fking thing. But car drives great, I arrive in Syd with no other issues whatsoever. A few Sydney people notice the idle in traffic and point fingers and thumbs up - something I hadn't experienced in Vic. So the IM240 test itself is done on a low speed dyno, to some VERY stringent testing which lasts 240 seconds, hence the name. This is the trace they have to follow, and there are markers on the test which show shift to X gear here, etc. Because they were super nice, they let me inside .. with a laptop! to have a look and watch the test but asked I not take video or photos (other than the photos outside). I read from most that they usually shut the doors and you have to wait outside, but they invited me in and I got to see the whole thing. Here are the emissions standards that need to be satisfied: The eagle eyes would note that for NON R34's (i.e R33 and R32) the standards are actually a lot easier than a R34 is, at least Pre-97. So almost 4-7x less in terms of "easier!" depending on what is being measured. So the car goes on, and I have a heartbeat of approximately 300BPM for 240 seconds straight. And the car... fails. Specifically it fails the HC3 part which is for effectively raw/unburned fuel. The others are more than fine. What could possibly be causing that, unburned fuel? Oh I dunno, how about that aftermarket choppy cam when a lot of the test is spent idling or driving super slow? It should be noted that if it was a R33, it would have passed. The guys there graciously gave me a chance to hook up a laptop and tweak the tune to see if I could fix it on the fly, which took about 45 minutes of my 30 minute bookings (its 15 min per booking slot), and the result is as below: When he turned around and gave me the thumbs up following the above test I legit teared up a bit. Right on the limit is OK. Every year after my specific limits have a 'less than' element added to it, so that's how close it was! Pro tip for those at home: A cat converter can only convert gas... not unburnt fuel. As you can see from my results the actual GAS part was well under. The drive home was a lot of relief. Even if I didn't have aircon working. I took this to my VASS consultant friend and the whole thing got signed off on by the director of Abmarc, who didn't seem upset that I chose not to do the emissions testing through them after all.. Note to self, coilovers ARE legal in Victoria. Also note: So are Varex as they pass under the 90db limit. They can't be controllable by the driver, but they can be controlled by an ECU. Did I mention Varex have an ODB2 controller as well so you can program that? They just have to open in the last 33% of the rev range as the test is done at 2/3rd of maximum RPM. And this is how all those luxury bimodal exhausts pass the test, you can officially be at 200DB if you want, 1rpm higher than the specified test RPM for that engine. The more you know.. The actual testers (especially in NSW!) are pretty keen to get things passed. They know the laws right and know when they see things that pass them. Then, armed with my VASS Cert and Plate I went back to the original Vicroads and was oh so very, very satisfied to have the same inspectors have to re-inspect the car with 0 visible changes since the first time and pass it.

As a 34 sedan owner, they fit fine (at least the whiteline ones do). Keep in mind if you have a NA, you need to actually get the D brackets that the OEM swaybar uses, because they are not included with a kit, it is implied you have em (which you won't if you have a N/a originally as they have no rear sway bar stock)

For what its worth, it is an extremely easy fix: Just changing some numbers here and hitting save basically.

Thats really what you want man.. Idle shake is cool and all until you have anyone in the car that doesn't think its great and it quickly becomes shitty. That cam looks the goods. Was the dyno run locked?

Its less choppy than mine. That said it probably drives right, and doesn't shake you and your passengers at idle in the seat (is kinda cool tho) and is the right cam! Which one did you go in the end?

The only thing I found from it (other than "I heard it was bad") was that it had the same bias as a Z32 BM57, which holds 50/50 split much longer (double) than a GTR one which splits to 60/40 much earlier. In other words, expect more rear bias with the HFM/Z32 BM57. Doubt anyone would notice it unless you tried both back to back in different cars though.

BEWARE I read bad things about the HFM one. I also found out that Z32 BM57's are NOT the same. The knee point on the Z32 one will lock your rears much longer before they start to engage the fronts. The GTR ones are the ones you want. There's a R34 and R33 version. What's the difference between those? I have NFI. I got the R33 GTR version and the clip does work on a R34. My R34 had nothing labelled on it's BMC, only a L6... which isn't L4 or L5!

I went from GTT brakes to an 8 pot KSport/D2/Attakd/Clone kit. I had similar symptoms to OP. I noticed that people who had GTR's who upgraded to the brakes I bought said they had no brake feel issues. I noticed that people who had GTR's who upgraded to Evo brakes and they said they had no brake feel issues. The BM57 was a night and day difference, much firmer. I got annoyed at it for many years. Just buy a BM57.

So the next step was aircon. I was tempted to go get the car engineered before I got aircon, but I assumed that once I had it, could drive it around legally, I wouldn't want to take it off the road to go and get aircon done. So the time was now. When holding a flaming turd in your hand, knowing you're about to unleash it on some poor business, its time to hit up google and find the person least likely to throw it back in your face and tell you to f**k off. So I ended up calling these folks here: https://www.melwideautoradiators.com.au/ Mainly to put this to the test: Their gallery shows a lot of cars that did not come from the factory with AC, and left there with AC. All I had to do was really use a different compressor than what the car came with, and some lines. Easy, right? I made my appointment, and drove the car there with a few photos and some discussion. In the past I always got some sneering shade when going places with a custom car, very much a 2nd class citizen treatment vs going in there with a coupe, or a GTR. However in v8 land, the tables are turned and people think it's cool for absolutely no reason. Which I'm all for. I got told it could be made to work easily, but it'd be an absolute pain in the ass and that he would definitely hate me by the time it was done. Good enough! I left the car there a couple weeks and the first part was super smooth. Lines and a new/moved condensor/combined receiver-drier got installed for space reasons, also my old stuff pretty garbage being old. John really knows his shit and made things as far away from others as possible. It got complicated later when trying to actually activate the system. I always thought aircons would 'stay' on so activating the system with a switch was fine, which i was OK with. this isn't so, and if the compressor is constantly on, the whole thing freezes solid in a matter of minutes. There's computers and thermostats and sensors involved toggling that compressor being on or not. Stock, the aircon logic is handled by the Nissan Engine ECU and not a body control module. That f**king Nissan ECU I finally got rid of out of my car for the last 10 years of it generally existing and being annoying. So I dug up my old ECU for their Auto elec guy to wire back in, complete with the Nissan pinout diagram and manual for the Aircon section so they could re-add it into the mix. But for AC it would be worth it. Wait a bit longer and to my suprise, providing all of the information, they found they could emulate the logic by using 'a series of relays' and the ECU wasn't required anymore at all. This was massively good. Can you see the aircon compressor in the last photo? I'm sure using a 15 year old gm AC Compressor is fine. Why replace it when it's accessible, naaah. Lets just see how it goes. Tested, working, excellent cold air - Time to start legal proceedings.

Pretty sure there is actually a Garrett S2 turbo, like all S2 stuff it is mind alteringly rare though. The TLDR is this isn't worth it, there is no easy fix, and the stock ECU is son of rajab and master of all. If you want to max out the stock setup to any real degree the ECU is the place to start, but unfortunately a combo of stock turbo, stock intercooler, stock injectors, stock fuel pump, stock exhaust, stock air intake, all of this is really not rated very much above stock power at all. And of course if you change it all, the sky is the limit. The GTR's can make more on stock gear because the stock [all of the above] is far more capable, but still behind any aftermarket offering in [all of the above] It's not worth doing basically - Car is worth more sold if there's a Viper in the garage lol.

*laughs in N/A V8* It is absolute bullshit though. My car has sat the entire quarantine period with half a tank of E85 in it though. I got dicked on Petrolspy where some asshole labelled it as $1.29. It was not $1.29 and in proper flex fuel fashion, I arrived with 0.05L left in the tank. Fkin pisses me off, if adding ethanol reduces the price of 91 when you add 10% of it, adding 85% of it apparently raises the price 200%. f**k.

I have read this, hello fellow 4 door person. It was nice to know my own foray into "I'll just do a few track days and just break everything, repeatedly" was not the only one, as I had many of the same problems until I said fk it, turbos can get f**ked, f**king flanges f**king manifolds f**king lines f**king heat f**king wiring f**king diffs f**king gearboxes f**king overheating f**king And then go do it all again

So now I had cool audio, an engine that ran, and a car that could drive around. However I was still rolling around on stock suspension. Prior to the build I was using a set of Sydneykid Bilsteins with Eibach ERS springs (ooh fancy), after a lot of consultation and SK's patience back many years prior. I was always super happy with them and they always rode and performed (to me) better than Shockworks, BC's, and Tien, pretty much any 34 I had ever been in. However after looking at the springs, I realised they had a 5kg front and 4kg rear. I later replaced them with an 8kg front and 6kg rear, which means I now have a lot of spring options. However that meant from my reading that I needed to get these shocks revalved to suit the new springs. I also was mindful that I have changed the weight of the car by putting a v8 into the fking thing. If GTR's have different rates and dampers to a GTT, then surely a V8 GTT would need some kind of different suspension to a regular GTT. That was my logic anyway. Also, one of them was doing this: However back then, was the only shocks I had. Mildly annoying and must be destroyed. So I could either buy new coilovers, or I guess reach out to Bilstein to revalve these to suit? If they even offered that, which I assumed would be $$$$$$$$$$$$$$. I reached out to a couple of very highly regarded suspension places and outlined what I wanted/what they would suggest re: Damper rates, spring rates, given what i had done with the car and what I wanted to do with it, and what handling characteristics I wanted. I got a mixture of "I dunno lol" and "Please buy our top of the range item with no regard to any of the customization you requested" So I asked Bilstein Australia on FB of all places and they were massively f**king helpful to my suprise. Like REALLY helpful. The information I found on the net (which Bilstein agreed with) was that moving engine weight around wouldn't actually have much to do with regard to valving the shocks, but it couldn't hurt. Though they agreed that GTR and GTT would have different valving, so perhaps it is better to weigh them... etc. Perhaps noone really knows. So in any case I found an VASS engineer consultant who had vehicle weights and I drove the thing onto them to see just how much the car weighed. I also asked at that time as to the legality of coilovers. I already knew they were okay, but you never know. In any case, he definitely gave the OK for them as long as not too low, retains x% of original shock travel (30% from oem etc) This was full weight, full tank of fuel, with spare, with all the audio in it, with my heavy as f**k BMW E30 M3 wheels and CST Cast 18x9 rims with 265 tyres, and big brakes, with me not in the car. To get the car revalved super accurately I sent bilstein a version of these photos with me in the car (I weigh 86kg so you can do the maths, the cross weight was 49.75% with me in the car which to me seems pretty fkin great though!) Carfolio.com says the weight of a r34 GTT sedan is 1430kg. I really don't know how accurate that is. Either that, or the LS is heavier than people claim it to be, or the RB is lighter than people claim it to be, etc. Yes I should have gone on a weighbridge BEFORE, I know. I went to a weighbridge recently to confirm the numbers above and I got the same result. That said, there were some results in his book of R34 GTR's and r33 GTR's etc weighing up to 1690KG (!) in true road form, with some stripped out track boys being 1300ish too. In any case, data in hand I sent my shocks to Bilstein. They said it'd take 2 weeks but it took about 10 days. I got a call from Peter at Sydney Shocks to have a chat about what I wanted and how etc. My car was always nervous under heavy braking on the track, (Part of the reason i changed the spring rates), and I really, really wanted it to be as solid as possible and more or less get the valving right for the true weight of the car, and where the weight is. I want to be able to really nail the brake pedal and start turning in to a corner and just know what the car is going to actually fkin do. I also mentioned I had to use OEM front and rear sway/antiroll bars. They hmmmm'ed and took that on board, and a couple days later they said they had revalved them - and did I want helper springs on the front as well as the rear? I was like "Yep sure, you're the expert if you say so!" They sent me this shock dyno result when they sent the shocks back to me. I also can't really read a shock dyno. Peter said he added a LOT of rebound especially to the rear and the graph has lines that seem to insinuate that, but he also seemed really happy and enthusiastic so that was great too. Very different to other suspension companies who were less enthused. Obviously I had great fun throwing the shocks back in to the car and setting heights, (making VERY sure the lowest point of the exhaust was 101mm from the ground) and getting an alignment. Took it for a drive and it was apparent from leaving the driveway how much better the thing was, partly of course because it was no longer on Koni/OEM suspension, but the level of composure is crazy good. The helper springs on the front and the rear take a little getting used to, because on any kind of aggressive turn you get an initial amount of body roll, which feels like 'squat' but it's.. sideways squat. I understand the theory behind it but it is disconcerting when you're used to not having that. But once you trust it and know that it's really just loading up the outside tyres it definitely works. It then dawned on me.... it handles like a MX5! They have very similar characteristics as to how the weight of the body moves around, how you play with the movement and let it get settled, etc. It drives like a MX5 with much more everything, more weight, more power, more grip, more heavy duty...."ness". Obviously it's not as nimble as a MX5, I mean only the driving style is eerily similar. But ultimately, it was massively more predictable than it was before and a definite benefit to the V8 is how 'well packaged' the whole thing feels. There's absolutely no way some off the shelf solution would have been as well done. And it cost way less than a new set of shocks. So sometimes asking around is a bit more beneficial than going on FB and asking "hey m8 what shocks does everyone run on their [car]" Summer moving up fast, time to get AC sorted, and better to do that before the thing gets engineered, incase I have to change... something, and would not want to change things after they're legal..

So, all freshly tuned the next cab off the rank was a decent head unit. During this build I noticed a lot of these f**kers start appearing: And while texting while driving is yeah pretty f**ked up, I really don't care if people text while at a red light because who gives a shit, give them a beep and move on. Doing it while moving though is legit shit. Do I get annoyed at all these cameras appearing where cars are usually stopped anyway instead of on parts of roads where people are moving... yes. Anyway. This is pretty shit for a guy who doesn't text while driving, but uses music while driving and changes songs by reaching over and shaking a phone or holding volume up on said phone, not while looking at phone. And because 99% of the time in a track ready modded car is basically sitting staring at tail lights listening to music, I figured this problem was on the list of things that were mildly annoying and should be destroyed. This is my boot, with subwoofer and amp. The amp actually came with the car when I bought it, but no sub because it had been stolen out of the boot, but the amp hadn't because Westside Melbourne. Since then I have some nifty straps and plugs to remove it in about 15 seconds for track days. I also have Audison Prima APK 165 speakers and tweeters https://www.audison.eu/products/apk-165/ I do not know what any of this shit means, because i got the speakers when I went to a trusted audio place and said "Bang for buck but actually kinda good thanks" the result is nice and crisp and clear and honestly pretty great. The current fine in Victoria for touching your phone while doing anything is $455 and 4 demerit points. The following head unit is cheaper than $455 so I ended up purchasing it. https://www.ebay.com.au/itm/HIZPO-7-Android-8-0-2Din-Car-Stereo-8Core-RAM-4GB-Radio-GPS-DAB-Wifi-DVR-4G-Cam/231960266999 If you click the link you will see this thing comes with many options. It is basically a full android tablet that fits in a double DIN. I ended up getting the DAB box for digital radio (cause why not) the dashcam (cause why not), the reverse cam (cause why not), the USB/3G Modem (cause why not), the external mic for phone calls (cause why not), but not the TPMS module because I don't have those in a skyline and neither do you. All in all it cost me less than a $455 fine. Armed with one of these: And a lot of time reserved for dodgy wiring, it was time to get to work. Obligatory shot of where things plugged in at the back: And that was it. It all worked perfectly with no issues whatsoever, and every little addon worked entirely fine with literally no problems at all. The only thing to wire in was the reverse light. Seriously. It took like 20 minutes total and me and friends had a good 10 free hours spare right after that, all confused. We had to make a tiny cut in the surround, where it sits behind the AC controls (its not visible) I used FCC launcher to make the 'desktop'. With ODB2 from the LS, Torque pro is great, I can get any dash that the ECU even has on there at the track, or the keen eyes see I can do TrackAddict for laptimes and Telemetry right from the head unit. And of course, I can do all of this without copping a $455 fine. Pro tip for anyone in the future, get Neutralizer, which is an android app. In a car with a loud rumbly exhaust it is a lifesaver, think of it as an equalizer that removes unwanted background sound by tuning around it. It is remarkably effective and when I drove up to Sydney at 110kmh, turning up the music entirely cancels out the sound of the exhaust, and not in a "lol it is too loud to hear anything else" kind of thing. Now that the car is rolling around, it was time to touch base with Bilstein Australia who had previously agreed to revalve my shocks. But before I did that, I had to weigh this thing....

Luckily the T56 has near identical ratios to a R33 GTST Gearbox that it replaced. As far as speed per gear goes it is 1: 73.5 2: 110.0 3: 150.6 4: 195.8 5: 264.6 6: 391.1 (lol) Cruising at 100kmh is about ~1600rpm. So 1st gear is a bit longer than previously, which does help a bit with grip. I get TC interference really only on a launch, 0-20kmh ish. However if I turn it off and stand on the throttle at all, it will spin tyres up from a standstill (I,e not hook) even if I just go WOT from idle. The Racelogic manages however much slip I dial into it, 20% is a decent amount for having that lovely sorta wheel spin takeoff you see all the journos do when testing cars lol. However once the car is moving, no amount of aggressive throttle causes wheelspin, it is really tame compared to the turbo setup, it does the exact opposite of wanting to kill you, and this behaviour is actually the most surprising/welcoming thing about the whole conversion. You apply the torque directly with your foot and it never overpowers the tyres or does anything unexpected, just feels strong, and linear and repeatable. I have done a cheeky skid just to see what it is like and it is very obvious immediately even to a complete drift n00b why V8's end up in drift cars for the above reason. (and 2 way diffs).

The background looks very USA/Canadian. Hard to know for sure unless you see it in person. If I was looking would I go see that car in person to learn more? Yes