dcv2.0

Ive got 17x9 drifteks front and rear, use 255-40-r17 on rear and 245-40-r17 at the front, neither scrapes. I will have to measure the offset as they were on the car when i got it. If you want to see what it looks like i can send you a pic

ok so i have found a couple of places that do r32 gts do luck style front bumpers but none for the gtr 32. If i have to buy the gts model one, does anyone know what is involved into fitting it to a gtr? all help welcome thanks guys

I have off my 32 a set of front braided brake lines These are race lines and hence not ADR approved. Cost me 120 to have them made. Had them on the car for about 1month, worked perfectly fine. Asking price $50 + postage(if req) please contact me via pm or 0425310340

As title states I have out of my mazda gtr an apexi avcr unit, ive used it for about 10 months, it has minor scratches and is fully functional. Price $380

I need new brake lines for my 32, the issue is that i have r33 gtst rotors and calipers on my r32 and lack the metal line that is normally found on these calipers. So basically i want a line that goes directly into the caliper. My question here is whether there is braided line kit suppliers out there that do this sort of length of line in their kits. If so i would appreciate some guidance, any info or alternative ideas are also highly welcomed. Below is an image of where the braided line must screw into. Banjo bolt or other

definitely interested in these

price drop $200 last chance before it goes on ebay.

pm's and sms'd those interested. I apologize for not making my original post clearer. The kit includes the intake section only. not the front y trust pipe and the hpi dumps. It includes the split intercooler pipe (not front y pipe for the exhaust -> dumps section). So it basically replaces the stock intakes and filters and pretties up your engine bay =). Hope this clears things up a little. regards D

$100 anyone?

afm's can be used i forgot to mention in the sms... just need one extra silicone joiner i believe and the filters would sit on afm's, having said that i have never used them so if anyone is interested in trial fitting before they consider buying this they are more than welcome to do so.

2xstock r32 gtr manifolds with chromed standard heat shields. $150

thanks guys for the positive comments. Due to moving house i need this stuff gone. Price: $250

sorry ZILLR im located in Perth - yokine area, DAS KAMU i will get some measurements for you soon, the gear is currently at workshop

i am assuming that would be your way of saying the price is too high.... (needless to say that was completely unnecessary) Im open to offers, however this is not an ebay kit and please consider how much these things cost to make.

I am not too sure mate, the mounting position would be the same, im just not sure about the flanges, i can measure it up and let you know if you like.

Ive got a few bits and pieces left from my previous setup that could pretty up someones engine bay. 2xTrust Filters 2x SS Intake pipes 1xAluminium y pipe all joiners and clamps in picture that are necessary for a direct fit. most of these bits have been made by briffa engineering so work is top notch. Like i said in the title, this kit is off my old hks2530 so im not sure if it would fit a stock gtr, if someone could clarify that would be great. Price; $400 D

Price Drop $900

Straight out of my car, comes wired into gtr harness as a package. Lt12s ecu X6 ignition module harness Price $1100 ono 0425310340 Cheers D

I actually thought the same about the cat given it's age, I was looking at a magnaflow one, but I rang around today a few tuning places including the one I use and they all recomended the stock cat regardless of power. The only concern all had was the ecu which I'm trying to replace. I will go for a test as is and see the outcome I guess.

thanks for your reply Sorry for the lack of info, it is an RB26, microtech tuned for 18psi, very rich tune judging by my fuel consumption. Motor has done about 90000km's and is very healthy. Im not looking for a performance cat just one that is very good at reducing emissions. I mean all the makers state they are good but like everything else that may not be the case hence why im looking to find out who has passed this test with similar mods and what cat they were using.

Ok Firstly i appologise if this topic was covered elsewhere, i could not dig up any info. So i basically got my car together over the past 9months into what is considered registerable state. The last thing required for the engineer and pits is the 5 gas emission test. Does anyone know any places that do this, given the engineer could not point me in the right direction i thought i would ask on here. Also given my mild settup (gt35,700cc injectors, microtech and standard cat) what are the chances of passing this. If they are slim what are my options ( in terms of better cat, better tune ect.) Advice or prior experience would be very much appreciated. Thanks D

10

9

8