irishGTSr32

Ill post up what ill be running! I hope to get to 300KW's but not sure what ill get really! Block back deck and beautifully cross hached CP pistons in all there glory........:grinno: smile for ur close up!:boobies: Full set of new lifters was gona go solid but no point as it ant gona be reving over 8k rpm , so got on to the guys at www.apexperformance.co.uk who sorted me out with a set for Very good money! tho i must say i rang my local nissan garage for the crack to see what kinda money they wanted for a full set!!!! O its a import we'll have to look into it! got a call back !!!!! There 90euro......(tuat for a sec class).......... then they said EACH LOL As iv said earlyer www.PowerHouseRacing.com came up top guys when a rang looking for valve springs from Supertech, tho these will be helping be got near 8k rpm Picked up the rad differance to the OEM item! And the best till last, picked up this PLAZMAMAN inlet with a Plaz throttle body too, must say build qulity is 100% as u can see from the pics below. Just need to figure out what im gona do with the bottom half of the inlet manifold!!!!!!!!!

strip down !!!!!! Head going next week to Martin Tracy @ westward engineering when the rest of the parts arrive. Full Port flowbench, CNC cut valves, new supertech springs and retainers etc!! Block,Crank,Rods were dropped off earlyer in the week, rebore .5mm over size with forged pistons to match, Arp,-Mains, Rods, and head bolts, Also dropped off my new injectors to get flow tested !!!!! Cylinder 1 seams to have been suffering badly from DET Its only really when ya look at a good(ISH) cylinder ya can see how DET has caused it to eaten into piston number 1 and has left its marked !!

Heyya doing lads! Been on the form for awhile but taut i would share my HCR32 with all you skyline loves. Scored by Andy @ Powervehicles. One late night i found this HCR32, grade 4 with a C grade on the inside. Happy to go ahead with placing bid on it i woke up the next morning to find an email saying YES you are the new owner of this. After a small wait the car was back at andys yard! and on closer inspection it was found to have, - Tein Super Street - Bride Drivers seat - Full exhaust from the Downpipe back - HKS mushrum filter Awyway i could fill up pages of the last 2 years but ill fill ya's in on the spec and ill keep you guys updated as it happens Engine: - HKS filter - GTR front mount Intercooler - GTR fuel Pump - Full exhaust (Of unknow make) - Turbo Elbow - Samco hose's - HKS Fcon-S - HKS rad cap - Nismo thermostat Suspension: - CST coilover (replaced the Tein one as they were shot) - Front and Rear Cuscon strut braces - Whiteline tension rod bushs - Apex Front upper camber arms - DW sub frame collers - DW poly bush's in controle arms Wheels - Rota Torques (sorry lads not that rich) 17 x 9 all around - 5Zigen Pro-Racer lug nuts Brakes - DB-Power Big brake kit 315mm - Endless Super street Transmission - Spec Stage 2 clutch - Tomei 2way Trax Advance - Nismo Clutch Pivot Body: - Standard Kit with URAS monkey magic bumper Inside stuff: - Nardi Deep Corn + Bell short boss - Greddy SMi Boost gauge + controler - Fcon Navigator - Turbo Timer (wow) Pic's of my motor The arty ones

Lol very lost but who dosnt love Farther Ted

Whats all this about IRISH school? LOL

Heyya doing man!!! What a build to start off with.... also building a angry rb20 at the min along with a plazmaman, tho surly it wouldnt bolt on and show improvement with out mapping

Thats the kinda power delivery i want looks nice n progressive!!!!!!

Hello guys need some advice on what kinda performance i would get from a GT30 with the following spec: GT3071 with 56 trim compressor wheel and 84 trim turbine wheel. The turbine housing would be 0.82AR and the compressor housing will be 0.50AR T3 flange internal wastegate setup. This was advised to me by my turbo shop. Could someone give me an idea of what rpm i would be getting spool up and where abouts full boost ? i dont really want a lagy monster!! but i know i cant have my cake n eat it too!!!!!! my Engine spec is as follows Rb20DET Forged CP pistons Block decked, bored and honed Crank polish Arp~head,mains,rod bolts ACL Mains,big end N1 water pump OEM oil pump (oil resistor + drain) (not sure if i need?) Supertech hyd valve spring kit HKS adjustable pullys head lightly ported with CNC recut valves Plazmaman Inlet manifold theres more but there the important bits!!! Many thanks Chris!

Is anyone out there running a GT2871R?????? or GT2860rs?????? id love to know what there like im buying a turbo very soon!!!!! also cant really warrent a 2000euro HKS GT-RS

bump on this anyone else with a GT-RS or using a GT28?

I had the very same prob! last week!!!! mine had sezied onto the crank!!!! I didnt know what to do!!!! as u say there is no room for between the pully and the oil pump!!!! My bro who is an engineer for RR aero engines came home n was very supprised also!!!! tho he did come up with the idea of dremel'ing noch's into the oil pump casing so as to get a proper grip on it (I WOULDNT EVEN DREAM OF DOING THIS UNLESS U ARE 100% SURE + im rebuild the hole engine and getting some block work as id be worried about the fillings geting into places there not ment to be) then heated up the pully slowly while keeping the crank cool with water. then POP it came off!!!! I was so happy it did!!!!!!!!!!!!!!!!!!!!!!!!

Heyya doing all looking for pistons seams my engine shop cant get them off he's suppler anymore Looking for ACL pistons at the min but finding it hard!!!!!! looking at supertech but found a thread saying they snapped the oil squirters n thats not very good!!!!! any info ? need these asap .5mm over sized

this the done thing? any probs wth doing it?

What kinda lag would i be getting using a GT3071?

Well r32 NA are hard to come by over here tho ill look into it!!!! and i want to keep RB20 yes i know ! rb25 flow better and would be easyer to start from there! But this is about keeping it a RB20!!! plus then you have to pull it apart n start agian -1000euro And yes Rb25 box here for new build!!!! the rest of the car is done just need enine now!