grepin

Hi all. Before I start pulling things apart I have an issue where my pulley for the aircon seemed to have destroyed itself. I am wondering if the pulley can be replaced (R33 Gtst). The inner part rotates with the nut and I assume the outer sleeve attached to the belt should all engage when aircon on. It just keeps spinning making a noise. Other than that it was cooling fine. Thanks

For sale HKS 2835 ProS 0.87 ar rear exh housing. Could be fitted to other turbos. Asking $350 firm and $15 postage interstate (outside of Adelaide). If in Adelaide could supply a dump pipe for $80. This housing alone retails for $800 from Greenline.

Thought you use money to buy stuff. Ringgit even. Need to fund a Skyline not games. I guess you cant help then.

I ahve been trying to run a Malaysian copy of Half Life 2 but I can only get a certain way before I cant get through a gate. Is this part of the write protection. There are no obvious cracks on it anywhere.

Try rFactor with the V8Factor mod. I use paddle shift for gear changes (auto clutch) however the clutch works well to get out of sand bunkers. The auto clutch boggs down and you rev stall a lot to get out. Both can be set up at once.

Selling a pneumatic gated Hiper Boost controller. Has had minimul use. Has a boost gate as well. Full instructions below to explain better. Worth $380 origonally now $150 posted firm. HIPERBOOST_CONTROLLER_INSTRUCTIONS.doc

I have a Hiperboost controller you can have for $150. Cost $390 origonally. Instructions here. HIPERBOOST_CONTROLLER_INSTRUCTIONS.doc

Plus being held up by customs + GST + getting a broker to get it out of customs + import duty. I have been there with one of these. Sometimes you can get lucky. Fantastic turbo I am getting 300rwkw with other gear to support.

Just wondering if people put lock tite on the studs in there exhaust housings. Tend to find mine working there way out. Also probably for the 2835 ProS Guys what are people using for gaskets now. Have mine off and had some copper wire in there but still think some gas is escaping.

Just wondering the best place in Adelaide for Manifold studs etc Thanks

I am selling a HKS 2835ProS Turbine housing. 0.89 ar with internal gate. Probably would suit or fit most HKS variants and maybe some Garrett. Purchased from Greenline for $800. Looking for $450. If in Adelaide I could probably supply a dump pipe to suit.

Seem to have lost my HKS actuator so need a replacement. Doesnt need to be HKS.

I have managed to loose my 15 psi internal HKS actuator between workshop or home. Currently have a 20psi actuator fitted but need a 15 psi for some testing. If anyone has one to borrow or sell let me know. Not ready to buy a new one at $200 yet. Thanks

I have managed to loose my actuator somewhere. was a HKS type. Anyway if anyone has an actuator lying around they wish to move on please let me know. Needs to be straight shaft. Thanks

It would be an actual shame to chop it up really. I am using a computer for my sims this is more suited to the Playstation. If I cant sell it then I will modify it and probably throw it out as I have bigger and better ideas down the track. Sort of just after a little cash to fund future projects. Not sure if your interested but I will take $50.

Bought this off the forums from another guy. Just bolt your wheel and pedals in and away you go. Is a little tight for my knees as I am bigger than the previous owner so before I chop it up its on offer. If I can get $70 its yours or angle grinder here I come. Greg 0412075359

Have decided to sell my boat to make room for upgrade. Was bought of a work mate a year ago as a learner for myself. I am happy to continue as a boaty so going for something more up to date. Anyway model is a Corvette thats all I know. Has a great 50hp 3 cyl Mercury that is oil injected (no oil mixing required). Has radio, depth sounder, and maost of the safety gear requirements. Just been registered. Since I had it the motor was serviced at Boat Scene with good reports. New plugs and impeller fitted. I installed a new extinguisher and some teflon on the skids. Tilt trailer with new single springs a year a go. Has bearing buddies with good berarings. This has been to Whyalla and Yorks no worries. Looking for $4300 neg. Greg 0412075359

Just wonder if anyone has had any experience/knowledge on welders out there at the moment. Just after a home handy man style. In the past have only used arc welders but know there are mig and tig versions around. Now I dont want to deal with gas bottles so gasless migs have caught my interest. What are the pros and cons when I can get a arc welder for $100 and a gasless mig will be $400 worth. Can it still do aluminium. Thanks

Just wondering if anyone had been today and if it was worth while?

Still interested

PM sent

Yeah that sounds about right. Cant really remember to be honost when I did it but for around $100 ish was a good day. Yes your tyres will be molten and pads worn with brake fade if you only have standard setups but you will come away all smiles. A great way to justify any money you have spent on the car.

Pretty sure no cams licence needed

Its easy. Just turn up for one of the practice days. Only costs around $80 from last time I did it from memory. You get around 5 sessions of 15min each. That was with bikes, cars and open top cars all having their own 5 sessions. Is great fun you can go at your own pace with no real rules pitched at you except common sense. There can be anything from race cars to toyota echos. Helmets long sleeves etc needed of course. Only thing I can say that intentional drifting is out as there are other cars out there trying to get around as quick as they can and may get pissed off. Last time I spun out a few times as I built up a little more courage trying a little too hard. Count me in for a day out. I dont get to many SAU functions but definetly in for a track day.

Hi All. Just would like to know what people think is the best driving wheel for PC. Games like GTR and V8 supercras etc. Thanks