simonthomasgoodwin

im sitting on 306rwhp and im pretty sure my injecters are standard(not100%) and dnt hav a fuel reg ?

i had this problem with my silvia.. under ur bootskin take out the fuel pump/floater and make sure its sitting in the right position. there is like a small cage like thing around the pump that it will slide in and out of when u remove it or put it back in.. make sure the floater arm isnt being fouled by this. from memory there was 6 or 8 bolts holding the intrument cover in.. try rotating it to see if it can move freely in a different spot. and also could be what GTS25S said aswell. also wen you take it out make sure the arm is actually connecting with the sliding sender unit. hope this helps! Simon G

can the bov be plumbed back? pm me

as said i need the above for my new turbo if any can help out much appreicated Simon G

check all ur intake fittings something cud b loose and if ur running th bov with 1 bolt then that would probably be it

hey man im sure you could just use some gasket goo on the gasket til you get a replacement wouldnt leave it there long tho gaskets arent exy anyway and as for the bolt look around ur car for one if its not holding anything important in should be right but i dont think there are many of those ones handing round in the engine bay.. ta Simon

can i get a price for the tune from anyone?

hey mate will the oil and water lines fit my 3076r? would u be interested in selling them seprately pm me

http://cgi.ebay.com.au/Turbo-Oil-Water-lin...=item41525113c6 should these lines suffice? it says single ball bearing on there tho im not 100% but i think its a dual BB (at work atm cnt go look at it) also once ive got it bolted on with correct lines n spacers etc.. is it safe to drive it or will i need a retune? and for a tune is it going to be costly seeming as its just being retuned to the turbo or is a tune just a full tune?

haha alrighty thanks guys thats a load off my mind so does anyone know of a trader on here that sells the 10mm T3 spacers and at what cost? another q.. anyone know about oil and water lines for the 3076 wil they be the same as my Apexi 400hp thats on there atm?

adriano.. rotate housings? is that just a unbolt slide it round rebolt? does it affect the flow? can anyone else confirm this?

so ive recently purchaced a gt3076r and now looking at the dist between the manifold and the strut tower it looks like it might not fit down there.. has anyone done this/will i need to get a new topmount manifold? thanks Simon G

sounds good goodluck

hey guys.. im newish.. aha thanks ive had my r32 since may and i get my opens on 1st Sept very excited to be able to finally drive :D :D Simon

hey does anyone kno where i can get the middle bit that says nissan uhmm.. coilpack cover from? my rb25 came without one pm me

hey this might seem like a stupid question but could you just buy the cf etc and cover it on the parts alredy on the car ie bonnet front bar etc.. or everything? haha if its possible what would be involved and materials would be needed? PS! that looks awesome mate really good job and you also have the satisfaction of knowing that you did it all too! super impressed!!! -Simon

sorry theyre in brisbane am willing to post at buyers expense

bumpp take the lot for 150

hey mate how do i no which set i need am after some for my rb25.. no idea what the -10 etc means tho.. thanks simon

sitting on 306hp atm with r23 w/ rb25, apexi 300 or 400hp turbo (not sure which 1)n a pod, greddy radiator, hks fmic, oil cooler, 3" zorst w/ 2 hi flo mufflers n no cat, Twin Plate brass button Clutch, Splitfire Coilpacks, shimmed diff, and i was told she had a walbro fpump havn looked at it yet tho running 1.2bar with blitz Dual Stage Boost Controller and Turbo Timer car has flashed over ECU with an Omoni Tune with no restrictors my goal is 500hp so wats next to get there ? thanks simon

wat r the advantages of a z32 afm? to power gain? does anyone have any comparison results ? im sitting on 306hp atm with r23 w/ rb25, apexi 300 or 400hp turbo (not sure which 1)n a pod, greddy radiator, hks fmic, oil cooler, 3" zorst w/ 2 hi flo mufflers n no cat, Twin Plate brass button Clutch, Splitfire Coilpacks, shimmed diff my goal is 500hp so wats next to get there ? thanks simon

hey guys got a r32 with an rb25 and need a new lh engine mount just wonderinf do i use one from a 32 or must i get one from a 33 thanks!! also if anyone has one in brisbane area tht would be tops! amd i no i need the square one not the one with 2 bolts if that helps

hey guys got a r32 with an rb25 and need a new lh engine mount just wonderinf do i use one from a 32 or must i get one from a 33 thanks!! also if anyone has one in brisbane area tht would be tops! amd i no i need the square one not the one with 2 bolts if that helps

uno wat they look like as says in good nic txt or call 0400 023 580 as i barley come on here, simon

oki doke thanks for the feedback Adam it just seemed like an interesting idea