blu hsv

bump

Launnnie

Hey i have a Haltech forsale was going to use it on my commodore but thinking of going a differnt way engine wise. it brand new never used it still has box and every thing here are all the specs. im after 1600 ono 0419329253 Features: Direct plug and play replacement of the OEM ECU, no re-wiring necessary. Uses the cars factory sensors Supports R32 GT-R twin MAF sensors Supports Sequential Injection (peak and hold) and Direct fire ignition Windows 2000, XP, Vista, Windows 7 compatible software Real time programming, instant hesitation free adjustment while engine is running Fully user definable 32 x 32 mapping Tuning via Volumetric Efficiency (VE), Injection time or Lambda Correction (MAF) OBD II Code Storing & Malfunction Indicator Light (MIL) Control * * (Access through laptop only ) Selectable onboard internal MAP sensor rated to 150kPa (up to 1.5 Bar or 22psi boost) Wideband "auto tuning" using user definable target AFR table USB and CAN Communication Port Factory Outputs: 6 x Fuel Injector outputs 6 x Ignition outputs Tacho, Boost Control, AC Clutch Relay, Idle Control Thermo Fan, Check Engine Light, Fuel Pump (Variable Speed) N-VCT ( Nissan Variable CAM Timing Control) Factory Inputs: MAF sensors, Throttle Position Sensor, Oxygen sensors, Coolant Temperature sensor, Vehicle Speed Sensor, Air Temperature sensor. Expansion I/O*: 2 x Analogue Voltage inputs 2 x Analogue Temperature inputs 4 x Digital pulsed outputs *Optional auxiliary harness required to be purchased Haltech Part # HT040003 Functions: Closed Loop O2 Control Decel Cut Over Boost Rev Limiter Closed & Open Loop Boost Control Gear Setup ACF On Base Tables Transient Throttle Enhance Correction Tables: Fuel Ignition Boost: Cranking Air Temp Target Correction Coolant Temperature Correction Map Correction Zero Throttle Gear Correction Cylinder Trim TPS Correction Generic Correction 1 Generic Correction 2 Gear Correction Post Start Air Temp Duty Correction Post Start Miscellaneous: Data Logging: 448Kb of onboard data logging, Storage for approx 40 minutes at 10 logs per seconds, 6 channels of data Max 20 channels logging capability Tune can be password protected in software Rugged anodized aluminum casing Power Requirements: Source: 8.6 to 16.5 Volts DC Consumption: 530mA @ 12Volts DC Physical Dimensions: ECU Dimensions Length: 154mm (174mm with MAP nipple) Width: 158mm Height: 42mm Weight: 680g (1.5 lb) Applications: Nissan Skyline R32, Nissan Skyline R33 Variations: GT-R, GTS-t Engine Codes: RB25DET, RB26DETT Transmission: Manual only (Automatic not supported) The Kit includes: Pro Plug-in ECU, USB Cable, Programming Software CD, Quick Start Guide, Instruction Manual (on CD)

I just pulled mine out and ran a 1/2 bsp (it think) tap thought it and got speedflow fitting and screwed them straight in. the hole was the perfect size i didnt even need to drill it

Im after a tps sensor if any one has any in good working order

Im after a Tps for a s2 rb25 or whole throtle body doesnt matter 0419329253

Hey all I Put a rb25 into my vl commodore about 6 months ago and i am having a few isues with the engine. I brought a wrecked s2 r33 for the engine, the engine has a gready style plenum and every thing else apears to be stock. I put the engine in and wired it up from the instructions i got from r31 forums, and the instructions said i need to hook up Temp sender wire Ign positive constant positive taco fuel pump triger Got the car running but it has trouble starting you have to hold your foot on the throtle it still takes a bit to start. and if you rev it up and put your foot on the clutch pulling up to the lights it stalls. the car had no Bov but i fitted a turbo smart one but it still does the same thing. I have cleaned the aac valve but no change I looked at the wiring diagrams and found i hadnt hooked the starter motor triger to the ecu so i fixed that but it still is hard to start. I found i didnt have power going to the aac valve/ idle control solinoid and Vct i fixed that but it still is hard to start. What else have a missed? Do i have to setup the idle properly now i have power to the aac valve?

i got a full set if your interested

Im after a s2 rb25 head in good condition complete Let me know 0419329253

Nearly every thing is gone. only have back seats from S1 and S2, rear boot spoiler, rear bumpers, back window, steering collum and side skirts

Not real sure but i think i saw a white r33 with that number plate to night in launnie not sure any one got a picture

wheels sold im down hobart on saturday would like to get rid of the doors and boot and front hubs if any one is interested

Hey im need 235/45/17 tyres i need 2 but 4 would be better would like good tread on them cheers let me know 0419329253

no sorry that was missing off the seat

Bump Coming to hobart on monday if any one wants any bits. Doors 50each Boot and spoiler 50 stock wheels with good tread 200 Want this stuff sold or i will throw it out