R6n350GT

Wiring Details White / Blue - CAN HI & CAN LO (LOOM) White / Green - CAN HI & CAN LO (ECU) Red - 12V+ Supply Black - 0V Ground Looks like wiring. Two wires, any auto elect can do for cheap.

I am wanting to organise a group buy for the SpeedM8 CANBUS delimiter for Skyline 350GT. They remove the limit without affecting any functions of the car. http://www.ncs-systems.com/prod/1458 £179.95 each for 1 units £129.95 each for 2 units. £122.52 each for 3 units. £107.00 each for 5 units. Anyone in Bris/GC wanting them please let me know. Prices do not include shipping, once we get a total amt i will get costs on shipping. Im assuming $5-$10AUD more on top of unit price if we get 5 units. If you are outside of bris/gc then you gotta pay additional postage ($7.40 for express post).

Apparently the US ECU is different to our JDM ECU.

If you have 5AT then use nissan oil but for the trans but for everything else see my post that diabolique nicely posted.

are you saying the V35 got the wiring in place for cruise or just media ?

I had this, i just flushed the brake fluid with penrite sin 600 and adjusted the clutch bolt and its all good I even made a video showing the noise, cant remember if i posted on this site or G35...

Hey Leon, thanks for that. It looks same as the G35 one, you sure its JDM specific? Cheers

Done http://www.skylinesaustralia.com/forums/topic/352017-how-to-fix-door-lock/

First of all if you are not patient or technically minded dont try this, pay someone to do it. There are risks: Risk 1: Someone in the US fried his ECU, no idea how ... Risk 2: If not mounted correctly you will get premature burn out of the actuator Risk 3: If not mounted correctly you will not be able to open the door (happened to me) you can fix but follow the below and you are right Im gonna write up what i found when doing this... Hope these tips help others and avoid going through what i did. After getting the door off finally i did i 110% this time. After you have taken you door panel off and taken the bose speaker off you will see a cable, undo the plastic wrap and splice two cables into it. Measure the length needed for the cables and use thick ones as mine were a bit short. 1. Route your wires you spliced into (purple and blue) under the BOSE speaker. Tip: Put a bit of tape on the blue wire so you know which is which if you used the same coloured wires. 2. Take off the inner door handle, you want to drill where the smaller hole is Tip: have the bottom of the hole line up with the bottom of the existing cable hole. Mine could have been a tiny bit closer to the bigger hole (which was a mistake) dont drill the big one.. 3. Now drill a hole in the closest plastic tab to the inner door lock. Tip: The hole should be 2cm high, 1.5cm in. 4. Mount the Actuator. The Metal plate you can get from bunnings for $5. It needs to be 30cm long. fold each end at 5cm mark and drill holes for actuator 1/3 of the way up. Tip: height should be around 2.5cm from the top of the door trim. Also put two screws on angles at the back to stop the brack from twisting when unlocking and locking. 5. Tape lock the 3 screw bracket Tip: Pull the tape as you put it on, too much and it will bunch up OR use locktite 6. Mount the door lock cable FIRST then run the actuator rod into the bracket. Tip: The way you mount it right is all the difference RIGHT way: Notice the L shape pin is push into the hole WRONG WAY: See the pin is sitting out, DONT install like this This bit is sort of Step 6a... Once you have the locking cable with bracket attached put that little L pin in the door lock bracket and click the cable in the hole. Now you will have to take the Actuator off again so you can put the rod in the end (i forgot to measure how much i cut off) and then put the rod through the first hole in the white tab and then through the black hole you made in the inner door lock bracket. Tip: As you put it through the hole you then put the rod through the top 3 screw bracket. DONT tighten yet. Hook up power to the actuator and see how far the rod goes in the unlock position, if clearance is good Now use a flat blade screw driver to tighten that last screw. Now test manually and with your remote heaps of times. Once right silicone that MF. Put some on the screws and some under where that L pin is. Your done! Just make sure the actuator can EASILY open and close, you dont want ANY struggle. If done good yours should look like these videos. CLICK THEM TO PLAY Locking mechanism: See how strong the actuating is, it fully opens and closes with the L pin always in the hole. I am trying to show that the bottom of the pin is visible at the bottom of the bracket. Actuator Mount: See There is very little flex when it actuates Inside door lock: Again see how it fully locks and unlocks, you dont want it to only move half way..

Double post my bad. http://www.skylinesa...-fix-door-lock/ MODS DELETE ME PLEASE

I fixed mine for $10 - new actuator .. I will put a DIY soon

"Emma @ Option1Garage" <[email protected] Emma Fegan 7 Remora Rd, Hamilton Brisbane QLD 4007 Phone : 3268 1113 Fax : 3268 2028 www.option1garage.com.au

180, you found a good set yet?? You going to get coilovers? Im looking into getting coilovers but not sure what camber kit... Or if i even need one.

So some V35s have them, some dont. Is there existing wiring that a button can be attached to or does there need to be a physical motor unit added to the mirror?

To Who? Would love to see what it looks like fitted.

Mark, did you get my PM, re posting the gear knob?? "hi mate yes i have the gear shift knob and it is in excellent condition with no wear marks since yours is the first pm i can give you dibs" Thanks

HFC + HR Megan V2 y-pipe + Fubjitsubo = win ! 180w, we lost you on the drive, what happened? Also cobey, i got some prices on stoptech slotted rotors and braided brake lines, plus stoptech pads. Good prices! Ill text i later. Remind me if i dont!

At ferry diner on ferry rd

PM yeah??? ha im used to meeting early when riding ! i will send u my # also, do u know how many coming?

I jumped on the R6 and went for a ride with a mate down advanced town, didnt get all the way there but turned around at that bridge and roads were fine that far.. saw about 2 little pot holes and thats it. Depends where everyone wants to go. I don't really mind, i just like the hills as you can go fast without going much over the speed limit at all. Doesnt matter where we go, Im just stocked we finally have one planned!

Would be interested in finding out how good the ride is with coilovers, i think the only way to go if your going over 19"s

Highway cruise to Byron or like scenery cruize through advanced town into nsw and back up?

I have the 350GT and drove it with 18, 19, 20. I like the look of 20 the best but the feel of 19 the best. Go 19, doesn't affect firmness much at all and is so comfortable.

Im still keen to meet up, i canceled some stuff on sat just to go and now its pushed back..

Im going to try and make this one, who is going? Can someone post a link, i cant find it on hardtuned.. Thanks