zac320

Doh! Rb25 matey

Hey guys I'm paying for me new long motor Tomorow, would I be better off buying a complete gasket kit from the states? I think all I need is exhaust and intake manifold Gaskets. Is there anything else I should replace on motor while it's out of the car?

Hey guys im selling my KTM 144 23HRS SINCE NEW!!! At 21HRS TOP AND BOTTOM END REBUILD WITH RECEIPTS FOR OVER $1800 Barrel recoated by electrosil Wiseco Piston and rings Hot Rods crank, bearings and seals JdJet kit put through carby Acerbis Rally 2 handguards Pro Circuit Expansion Chamber Brand new back brake pads Near new rear tyre 4 Spare Air filters I am chasing another bike preferable a Yz 125, but must be a minimum $1000 my way. Also intrested in Cr's Kx's and Rm's, 2006 and up. Very regretful sale but a genuine one, will not discuss reasons on here. Feel free to txt or call me on 0419188921 for more info. Bike is located in Bairnsdale 3875 CASH SALE IS $5500

And here I was thinking I got another helpful reply hahaha

Heads off. I bought the block. I have a head

Hey guys I picked up a bottom end for $200 it's comPlete and was running. For the sake of $300 is it worth putting new rings and big ends in it? Cheers

Hey guys, i bent a rod in my engine(hydrolock), so i have all the accesories, head, flywheel ect, It needs to be in use-able condition, im wanting to pay around $600. I live in Bairnsdale 3875, so the closer the better otherwise frieght will be heaps Thanks Zac

Hey guys, i bent a rod in my engine(hydrolock), so i have all the accesories, head, flywheel ect, It needs to be in use-able condition, im wanting to pay around $600. I live in Bairnsdale 3875, so the closer the better otherwise frieght will be heaps Thanks Zac

Hey mate i am intrested in Engine cauld you give me a txt on, 0419188921 Tried to inbox you but yours is full Cheers zac

Yeah your probably right mate, I was just about to pull it and strip it down then ahwell I'll do something else then haha

It is for a patrol mate. Was going the 30det route. But I've spoken to an engineer and he saidiota a bit of work with emmisions ect, he said if I go stock 25det, as in intake exhaust and turbo he will pass it. 2 conrods are bent as the engine won't fully turn over. Bores look fine except from a bit of rust on them, when I mine bit, it's under cover and it gets sprayed with crc frequently and the "rust" wipes off with my finger. When I say 26 rods it's just because I can get a set for $75. Currently just the block is siting in car with every bolt but removed. I didn't have an engine crane till a couple of days ago. I guess I'll pull it and check the bearings, if there's not rust, (shouldn't be motors full of oil) I'll slap the new rods and rings in, car was running fine until the hydrolock. And bores haven't been marked from the lock

I know but I can't find any bottom ends in good nic. Answer this I had about 3 liters of water in my engine when I drowned it as it was siting there in the water. It sat for about a day and I replace oil/water lol. Bearings would be rooted yes? I'm Considering just pulling the rods and putting the 26 ones I got for $75 in, plus might aswell throw new rings in it so there's $250 all up and then just my time.

How much is a good mic? And is it hard measure clearances out of round? Ect I wish someone had a good con 25 bottom end!! Im from bairnsdale 3875!

Hey guys I'm doing my first rebuild on a car engine. Done plenty on dirt bikes chainsaws ects. Here's a run down I'm pretty much just giving my rb25 a freshen up while I replace a bent rod due to a hydrolock. Reuse standard head (maybe new valve springs) Arp headbolts Reuse pistons with new OEM rings Rb26 rods with arp bolts Acl race series bearings mains and big ends(reuse rb25 piston pins on 26 rods?) Now it's all pretty straight forward except bearings as I've never done them before. Is plastigauge good to use? Can I just use it to measure clearances? I don't own a micrometer and would rather get by without one for now. I just need to know how to measure clearances so I know what bearings to order. BTW - Small country town no "engine builders" around, just a bunch of old blokes stuck in their ways. Yes it would be easier to get a running 25 shortblock, cheapest I've seen is $700 in the city so add $300 for my travel expenses and we are at a $1000 which is what this freshen is probably gonna cost me! I know what engine I'd rather have. Here's a quick list of prices off me head Genuine Nissan gasket set $200 OEM rings $180 Bearings $250 Rb26 rods $75 Arp head studs and rod bolts $300

He much that cost you scribble?