Search the Community
Showing results for tags 'ap racing'.
Found 6 results
-
Best ap racing calipers Have a few sets of ap calipers. See photos, 6 pot, monoblocs with open swing bridge for fast pad change. Up to 390mm rotor capacity, minimum 340mm. Top calipers $2800 per set Bottom calipers $3100 per set. Post world wide. Rotors available. PH 0431113255.
-
Ap racing 4 pot calipers Brackets to suit 355mm rotors Rotor hat and stud kit Goodridge Braided brake lines Ap racing brake pads Everything is brand new and unused Brackets will suit r32/33/34 GTR and s14/15 and 5 stud converted Nissan. Calipers will take any rotor from 330-400mm with the right bracket. I can assist with this if there is a specific requirement. $3000 -
Hello, I have a full kit from R35 gtr Fia-gt1 race car. It is also used on many other endurance cars. X2 L&R Cp6160 front calipers X2 carbon cover X2 L&R Cp6078 rear calipers X2 carbon cover X2 L&R 390x40 mm ap front rotors. X2 L&R 355x32 mm ap rear rotors. Ap racing T-Bobbin x48. X4 pagid or pfc front pads. X4 pagid or pfc rear pads. $9500. Please no offers, time wasters. Only the best. Ph 0431113255 -
FS: AP Racing Pedal Box + Tilton 3in1 Billet Reservoir OK guys, this is for the serious people. I have for sale an AP Racing brake and clutch pedal setup (part no. CP5517-1) Twin master cylinder brake with balance bar and remote bias adjuster. This model is commonly used on the American NASCAR. Comes with 3 master cylinders which are all the same size (part no. CP6465-202, 20.2mm bore size) . Comes with braided lines and fittings. Also comes with a Tilton Racing 3 in 1 billet aluminium fluid reservoir (part no. 72-570). Pedal box, master cylinders, braided lines, fittings and remote bias adjuster are used but in very good condition. Tilton reservior is brand new and unused. All up items to replace are over $6K. This is a boosterless system, so will massively clean up your engine bay and free up heaps of room too. Asking for $3500 ono. Located in Wollongong NSW. Willing to post at buyers expense. -
BRAND NEW IN BOX *Ideally would like to sell in N. America, but willing to sell abroad if you have a friend in the US able to facilitate. Endless 6 POT/4 POT Racing BBK Part# ECFXBNR34 (R34 GTR) 6 Piston Front Calipers, 4 Piston Rear Calipers 370mm x 34mm Front 2-Piece Floating Rotors 332mm x 30mm Rear 2-Piece Floating Rotors Blue Mounting Brackets, MX72 Brake Pads, Endless SS Brake Lines, Fasteners Calipers are Alumite Racing Finished (Super Hard Anodized). Rotor hats are TUFRAM coated. The bronze finish on the rotor friction surfaces is a break-in coating. The non-friction rotor surfaces are super high temp coated. These are direct fitment for the R34, and will fit the R33 and R32 with minor modification by drilling out the hub caliper bolt holes to 14mm, or using thread inserts in the brackets. This is an $8k (USD) setup before shipping and duties. It would take over a month to get (USA) if ordered today. Asking $7200 (USD). Located in Orange County SoCal. Contact: PM Payment method: Cash, Zelle, PayPal (contingent) Shipping: Yes, buyer pays all fees. Local meet up in public. Reason for selling: Going with a different setup I've been a member of this community since 2006. I can provide stateside references if necessary. JC -
Hey All, My old for sale thread sorta just got added to and is old and messy now. Thought I would start a new thread that actually had the items for sale listed. All items are located in North Brissie. (unless stated) Postage can be arranged, at buyers expense. My best contact is either mobile 0428142684 or email [email protected] rb26 coil packs - $200 ono. These are standard coil packs, spares from one of the 4 engines I had at one point, but were in working condition when the engines were stripped. sard 800cc injectors - $600 These have about 5000km of use on them. I wil be upgrading to higher flowing injectors. - does not include fuel rail. AP racing 6 pot calipers, 354mm 2 pieces rotors and fitting hardware - $4300 These have about 5000km of use on them, mainly just daily street driving, have seen about 5 laps of QR and performed wonderfully. Greddy plenum - $800 This has about 5000km worth of use through it, runs the 6 throttle bodies still. - does not include throttle body assembly. Stock rb26 plenum - $150: LOCATED IN TOWNSVILLE This is off one of the engines that I had that got stripped, only the plenum, no throttle body assembly.
