Search the Community

Hey guys, Thought I'd drop an update on the 6MT swap on my 2002 350gt-8.. On Saturday I dropped the diff, driveshaft & CVT with the help of a friend & only nearly killed him once with the cvt falling off the jack hahaha. Got it done in about 2.5-3hrs with a few hours prep I did the weekend before. Prep like drop exhaust, remove most of the bellhousing bolts, CVT clutch lines, loosen what driveshaft bolts I could etc. The most difficult parts were the little things really, remove this to get to that etc. Going through the CVT inspection plate to remove the X (I forgot what its called- between flywheel/torque convertor) otherwise the torque converter will still be attached and fighting the removal of the gearbox. Removed started motor, cable tied it aside to spin and wedge the X to get to the bolts through the inspection plate. Also removed the CVT dipstick & a loom bracket to get bellhousing bolts off from the top inside engine bay. Didn't have to touch the interior just left it in neutral to rotate driveshaft, disconnected gear linkage, was a peice of cake actually. I have a question though.. I sourced a CD001 6MT through this forum like at least 3 years ago for 1k before I knew of the difference. Is it possible to rebuild a CD001 so it has synchros like a CD009 or at least strengthen it?? also I've watched a bunch of youtube vids and I'm getting the impression that it's better to weld an open diff over a VLSD. Can anyone explain why this is please? Also have a 2003 350z VLSD I'm installing along with Whitline bushings essentials kit. Will measure up the driveshaft when 6MT & diff are installed. Next up is to prep the Z1 clutch for install, remove auto flywheel, rear main seal if required etc, solid bushings, interior prep, prep 6MT crossmember, install 6MT, short shifter etc, handbrake relocation(the cable is already right where it needs to be running through the tranny tunnel), clutch/brake pedal install then once that's all done scratching my head for a day maybe dealing with electronics hehe.. Just goto bridge the neutral safety switch and figure out reverse lights I think.. I'm going by this thread below mainly. But didnt even look at it when getting into the job, basically just unbolt remove whats in the way and drop whats needed. https://my350z.com/forum/engine-drivetrain-and-forced-induction-diy/552038-5at-to-6mt-swap-info-diy-guide-thread.html Yes I'm more than likely forgetting a lot, but it's pretty straight forward. Having my mechanic friend there for really helped figuring out the inspection plate X removal & with tips for getting more leverage/using the car to our advantage. Like loosening the axel shaft bolts with the 2nd spanner pinned up against the sway bar, removing the the driveshaft still attached to the diff as we didnt have the 8mm allen key tool required for the diff side driveshaft. ALL THIS WAS DONE ON WITH THE CAR ON JACK STANDS WITH BASIC TOOLS BTW...I'm waiting on an order from the USA- 'Never Ending Details'. DO NOT USE THIS COMPANY. They f**king suck. Barely any communication, Took ages to ship (nearly 2 months) and that's with me threatening them with a VISA dispute. Anyways just thought I'd add my experience with them. Pretty much follows the multiple bad reviews I've read online, same shit. The order was for flywheel/pressure plate bolts/various peices as it was a lot cheaper than going through Nissan (eg $17.50 VS ~$2 for 1x OEM flywheel bolt) I'm stoked the hard part is pretty much over. More room for activities now hehehe. BTW, the goal for this car is to make it into a nice street/semi drift capable car, with strut bracing/chassis reinforcement, coilovers, camber/angle mods & maybe a plenum spacer/intake being on the cards. Already has a mean sounding full borla exhaust & headers from the previous owner + ditch the wack bob jane special rims for some lightweight Rays TE37's. This car has been sitting for 3-4 years so I'm feeling really accomplished and excited to get her on the road again I will try to keep you guys updated. Cheers, Seb