Search the Community

Team, I have some Tein suspension that has always been in my car and after my question on replacing bushes I was also looking at the Cusco sway bars. Problem is I do not know my spring rate in the current coilovers. They are bound to be stiff though as it is a rough ride. Do I look to upgrade the sway bars with cusco items which are very stiff front and rear? Do I use the standard links or is there something else you recommend? Do I swap the coilovers out for some Tein Flex Z's with adjustable dampers and spring rates on those are Front 7kg Rear 6kg. If I do that how do I match the sway bars to those? This is a street car 98% of the time. Or do I go Whiteline which comes with a complete kit (links and all) and then adjust with the suspension shop to suit my current teins? Thanks again.

Hi, see items below for sale - all items are used All items are negotiable - can freight at the buyers expense or pickup Located in Griffith NSW 2680 Photos Attached Standard R33 GTR Turbo set - includes manifolds and heatsheilds, only has 1 stainless down pipe. Minimal shaft play Manifolds do have holes in them due to EGT sensors being fitted previously - one hole per manifold Looking for $120.00 for the pair R32 GTR Drivers side A/C Vent - was removed to fit a gauge $25.00 Standard RB26 Valve Springs with Retainers Came out of a Nissan reproduction engine so not many KM's on them $40.00 Standrad RB26 Camshafts intake and exhaust Came out of a nissan reproduction engine so not many KM's on them No Picture Looking for $80.00 for the pair R32 GTR A/C Condesnor Fan Tested Still in working order $65.00 CUSCO Radiator Cooling Panel R32 GTR Like New , has a few minor scratches and a rub mark in the RH corner $45.00 R32 GTR Speedo Cluster 340KM Bad Points - KM Count has gone crazy/ Not reading correctly , speedo works fine and Front Torque gauge dosent Work $70.00

Hey guys Im about to place a bulk order for my R32 GTR in the states. Im kinda stuck between the Cusco Street Zero A's (8/10 spring rates) and the HKS Hipermax IV SP (7/7 Spring rates) Wheels are 18x9's with either a 255/35 or possibly a 265/35. https://www.rhdjapan.com/hks-hipermax-iv-sp-coilover-suspension-bnr32.html https://www.rhdjapan.com/cusco-street-zero-a-red-coilover-kit-bnr32.html Also when is a front camber arm needed roughly? To give an idea of the ride height im gonna have I included a couple pics below. Id perfer to stick with the Cusco fixed arm in the front vs an adjustable I see they offer 3 different sizes +5mm, OEM and -10. Im assuming for my planed ride height the OEM would be better? Thanks for the help.

Hello, curious if anyone tried Cusco's front license plate offset bracket for R32. I can't find any good picture of it mounted... https://www.rhdjapan.com/cusco-front-license-plate-offset-mount-bnr32.html

Hi All, Clearing out the garage and found a few things i'm unlikely to have a use for. Trust/Grex Oil cooler. Sandwich type with thermostat. Suit R32 GTR and mounts the core in front of the AC condenser. $700 R32 Cusco front and rear strut Braces. $80 each HKS pods suit stock afm's $50 R32 GTSt LH Tail light $50 2 boxes of GTR junk, stock exhaust manifolds, heat shields, intake resonator, twin turbo pipe (missing badge), bunch of oil and water lines, overflow bottle $free Stock R32/S13 suspension arms, pretty sure i have 2 sets of all the rear arms, $20 per arm R32 GTR steering wheel, pretty rough, has the GTR horn button $50 S14 diff, pretty sure it's a manual 3.9ish ratio $50 S13/14 drive shafts 3x2 bolt type $50 a pair. Prefer local pick up but i can ship at buyers expense. Contact via pm.

Cusco RS 1.5way centre in a r200 housing out of a r33 gtst 4.11 gears 5 bolt shafts and hubs to suit. Shafts are freshly rebuilt After $1200 for it all. Not negotiable. No swaps.

Cleaning out my impulse buys and left over bits from the years gone by. All parts are located in Brisbane, South Side, and inspections are welcomed, just message me on here or on Facebook and I will try and get back to you as soon as I can. I will post at buyer's expense, so if you are located elsewhere and if you are interested, please contact me for a quote on freight. Thanks, Cameron. Nissan BCNR33 Skyline GTR N1 Turbos Near new condition High temperature competition coating on exhaust housings Selling due to going with a larger setup $1250 Nissan BNR32 Skyline GTR G Sensor Used G sensor Worked perfectly before being removed from the vehicle Hard to find these days without impact indicator showing $250 BCNR33 GTR Skyline N1 Center Triple Gauge Cluster R33 GTR N1 center triple gauge cluster Worked perfectly before being removed from the vehicle $100 Nissan Skyline GTR R32 R33 R34 RB26DETT Sard Twin Spray 800cc Top Feed Injectors Worked perfectly before being removed from the vehicle Supplied with plugs Only removed from engine due to changing fuel to E85 and needing larger injectors $500 Nissan Skyline GTR RB26DETT Carbon Fiber Timing Belt Cover Unknown Brand I bought it when I was in Japan $100 Nissan Skyline BCNR33 GTR RB26DETT Boost Control Solenoid Used Nissan RB26DETT Boost Control Solenoid Worked perfectly before being removed from the vehicle $50 Nismo Skyline BCNR33 Series 3 Front under Diffuser Genuine NISMO S-Tune aero body kit front under bumper spoiler for the Skyline BCNR33 R33 GTR Was over $1000 brand new (http://www.rhdjapan....ne-bcnr33-56310) $550 Nissan Skyline BCNR33 GTR N1 RB26DETT Air Box and Snorkel Nissan Skyline BCNR33 GTR N1 Air Box and Snorkel K&N Air Filter $250 Nissan Skyline BCNR33 GTR RB26DETT Air Flow Meters Factory RB26DETT air flow meters Worked perfectly before being removed from the vehicle $200 for the pair Trust/Greddy T78 33D Turbo Kit Trust/Greddy T78 33D Turbo Trust/Greddy Exhaust Manifold Trust/Greddy External Waste gate with screamer pipe Trust/Greddy Front Suction Pipe Trust/Greddy Heat Shield Custom Dump/Front Pipe Trust/Greddy 3.7” “Hi-Power” Ceramic Coated Stainless Steel Exhaust Hardly used, selling due to going back to a twin turbo setup $3500 KSP Racing Equipment Carbon Kevlar Rear Bumper Cover to suit Nissan Skyline R33 GTST or GTR Brand New still in box KSP Brand Carbon Kevlar $200 Nissan Skyline BCNR33 GTR N1 Radiator Used Worked perfectly before being removed from the vehicle $100 Rasty Mate FRP Boot for Skyline R33 GTR/GTS-T Flat Truck Style Painted in QM1 White GT Wing Mounts Some Cracks in the paint behind the wing mounts Very light @ 5.2kg $500 Full Carbon Fiber 1550mm 3D GT Wing Cannot remember the manufacturer 1550mm Wide Full Carbon Fiber Construction $500 R33 GTR Front Lower Arms Stock R33 GTR Front lower arms with both ball joints I was going to modify to get more front negative camber, but I no longer need them $150 for the pair Nismo RB26DETT Engine Mounts Brand New Still in Box Nismo ones are a bit stiffer than Standard Engine Mounts $150 Nismo Clear Indicators Brand New Still in Box $80 Nismo Carbon Fibre Side Pillar Garnish Brand New Still in Box $150 R33 GTR R200 Competition Diff Brand New Cusco 2 way Center Brand New Crown Well and Pinion Greddy Extended High Capacity Diff Cover Diff Cover has been modified to clear a close fitting exhaust 4.11 Ratio (Stock) $2500 R33 Auto-R FRP Head Light Covers Brand New Very light and well made $250

Up for sale is my cusco 7 point roll cage for r32 2 door with sunroof which are hard to come by as nearly every bolt in cage is for non sunroof. In Pretty good condition, never been in any accidents and comes with everything needed to bolt straight into your car. Never got a chance to fit it to my car and reason for sale is have decided to go a custom weld in cage instead. It is 40mm in diameter and 2mm thick and made from Cold drawm seemless carbon steel. Full details can be found at http://www.rhdjapan....sh-nissan-61791 Contact me by pm $600

Item: R32 Cusco D1 6 point full cage including side intrusions. Resprayed in Cusco blue(except for 1 bar too show authenticity) Cond: Excellent, couple of scratches on side intrusions. Reason for sale: Going weld in. Price: $1000ono, will ship... PICS: ALSO HAVE MANY PICS ON MY PHONE, MSG ME FOR MORE. Item: whiteline 24mm adjustable R32 gtst front sway bar Cond: good, perfect working order. Reason for sale: not needed Price: $200 ono Item: r32 gtst turbo injectors Cond: good, working order. Reason for sale: not needed Price: $50 Item: Blitz Pod Filter Cond: couple of small holes, nothing major, still works well. Reason: air box price: $15 Item:R32, a31, r33, r34 Bride side mount seat rail. Cond: perfect. Price: $220 Item: Nardi classic 360mm flat Cond: Excellent, small abrasion as seen(looks worse in pic), no horn button($15 on ebay) Price:$150 Item: Blitz R-Fit piggy back ecu (same as an safc) Cond: brand new in box Price: $250 (rrp is $350 on this and its brand new) Everything is located in Melbourne, inner eastern suburbs. PLEASE MSG ME ON MY MOBILE 0407 056 817!!!! DONT PM ME AS I DONT COME ON HERE OFTEN. THANKS.

Hi Guys, Selling off parts as the car is gone. AP Racing 5000+ These are brakes i had purchased off someone else, however i haven't used/installed them at all. Not sure of discs/pads brands. I've heard AP calipers are made in England and elsewhere, theses are from England. Calipers are what they are and include mounts, discs with the hats, all nuts n bolts and pads. Price is $3,200 Rays CE28 18x10.5 +18, 5x114.3 These are factory matte black in great condition with all stickers. No gutter rashes, just minor scratches from either tyre shops or wheels banging together. Come with Nitto NT05 275/35/18 tyres made 52nd week of 2011. 3 tyres are 90% new and 1 tyre is brand new due to the previous tyre being poked with a knife. Do not come with centre caps nor valve caps as they seem to go missing at the tyre shops. Price is $3,800 with tyres. R32 GTR Cusco Zero2 Bought these from Jesse Streeter about 2 months ago. Bought with around 8000kms of jdm road on them. Price is $1,300 Contact: 0416751515 or PM Location: Sydney Prefer to have this picked up. Cheers David

FS: S13 Onevia rolling shell. Unregistered atm, however can be registered. If buyer wants, can negotiate removal of some parts to decrease price. Has no engine, gearbox, driveshaft or exhaust. Body: - 180SX front +20mm fenders - CA pignose front bar - Standard Silvia bonnet - Rear +20mm widebody guards (not yet installed) - Rolled + pumped rear standard guards Braking - Cusco BMC Stopper Front: - R32 GTST Brake Calipers - Slotted Brake discs - Unknown brake pads - ADR approved HEL brake lines Rears: - R32GTR Brake Calipers - Cross-Drilled rotors - Unknown brake pads - R33GTST Drum Handbrake assembly + cables - Eagle auto handbrake adapter plate - ADR Approved HEL brake lines Suspension - FETs Front Strut Brace - FETs Rear Strut Brace Front: - Sunline Racing S14 Front Coilovers - S14 front knuckles + 5 stud hubs - S15 Front Lower Control arms - Nismo Power Brace 2 - Circuit Sports castor arms - S15 Tie Rods and Ends - Energy Suspension uprated steering rack bushes - S13 front sway bar - Fender braces - GKTech solid steering column bush Rear: - S14 Rear Subframe - SMM conversion solid subframe risers - SPL solid diff bushes - Tein S13 rear coilovers - S14 lower control arms - S14 rear knuckle - S15 standard suspension arms - S15 rear sway bar Interior - Safety 21 5 point bolt in roll cage - Stripped interior - Sound deadening removed - Removed AC and assoc. piping - Removed Heater and assoc. piping - HKB Boss kit - Nardi Classic 360mm Steering Wheel - Blue titanium steering wheel bolts - Sparco fighter driver's seat - fuse box and battery relocated to passenger side seat Drive line - 4.36 open diff Engine bay - Circuit Sports Aluminium Radiator Overflow Currently rolling on a set of S15 wheels. Looking for $3000 ono, open to serious offers. Can negotiate decreasing the price by removing parts. Cheers

Hi all, Cusco Brake Stop I have a used Cusco brake stop, I never had the chance to install it onto my car, it reduces the spongy feel when braking by decreasing firewall flex. - $80 EBC Reds (new) These fit on the rear of a r32 gt-r im not sure what else they are compatible with. (If you want a photo of them in their packet pm me) - $45 Bosch 023 in R32 GT-R Cradle This is fitted to a r32 gtr cradle, so it a direct drop in for any one with one. The 023 is said to be the same as a Nismo pump so will produce very similar flow rates. - $120

Make: Nissan Model: 350Z Track Year: 2004 Body Style: (Coupe/Roadster/etc) Colour: Pewter Grey Version: (Track/Touring/Anniversary/etc) Engine NA Transmission: Manual Interior Material/Colour: Sunburnt yellow Odometer: 12*,***kms Price: $24,500 negotiable Contact Details: 0410888383 Comments: Up for sale is my 2004 Nissan 350z Track Edition. The car has been great since the day I purchased it, I've never had any trouble with it, the car is serviced regularly by me, the oil gets dumped every 2500 to 3500 kilometres depending on how burnt the oil is. I have been told this is excessive but I don't like running with burnt oil. Over the years of ownership I have upgraded some components for better performance as listed below: CUSCO ZERO 3 - COIL-OVER SUSPENSION (20 way adjust-ability) CUSCO - REAR CAMBER ARMS CUSCO - FRONT A ARMS CUSCO - FRONT AND REAR SWAY BARS This set up alone cost $4000, I didn't want to lose comfort but be able to customise it easily to different drive types. Drives just like factory now with a bit more sharpness plus room to improve with its adjust-ability. (complete OEM suspension + camber + a-arms + sway bars can be included) TOMEI - EXPREME V2 HEADERS STILLEN - HIGH FLOW CATS X FORCE - EXHAUST SYSTEM K&N - COLD AIR INTAKE, AND PLENUM SPACER (complete OEM exhaust can be included by request) These modifications have opened up the throttle response and given the car a exotic exhaust note without having any annoying back pressure sound while cruising. The only time there is any rasp in the exhaust note is in 2nd gear at WOT which in my opinion fits the car. VOLK- GTS 19 INCH (9.5" front and 10.5" rears - brand new these cost $4600 plus shipping) Currently running on about 80+% tread with federal tyres evo 595's, the grip on these tyres is awsome, (medium to soft tyre). NISMO - TITANIUM SHIFT KNOB I-POD CONNECTIVITY - integrated into the OEM stereo and also charges the ipod/i-phone the standard stereo sounds great, good balance for the cabin setup. (extra speakers included + oem head unit) The clutch and flywheel have been replaced with a custom single plate heavy duty clutch, and a extreme single mass lightened flywheel late last year. There is some light chatter from the flywheel but isn't overly noticeable while driving but the clutch peddle is very light. As a standard car it is solid on the road with very minimal road noise, with cruise control for freeway driving factory Brembo braking system, this car is the complete package with nothing to spend. The Zed has been meticulously maintained and never missed a beat. Regretful sale but selling to cater for other commitments. I highly doubt you will find a Z car like this one, there are some chips in the front bar and a small dent in the passenger door (whilst in carpark) but overall for a 10 year old car it is immaculate. No low ballers please, anyone that has a real interest please call or text me with any questions, I'm am negotiable on the price to an extent and have a set of Advan AVS 18" wheels which i can include as an extra cost or replacement for the Rays Volk GTS wheels. (subject to price adjustment) The pictures don't justify how this car shines and looks under the sun, anyone with a real interest in this type of car will be impressed. http://www.carsales....0/?Cr=6&sdmvc=1 check out the link for pictures. thanks for viewing

cusco brake master cylinder stopper addpats to cusco strut brace $90 need it gone located in brisbane 0421883199

I have sold my GTR so no longer need the parts/spares. All parts are located in Brisbane south side, and inspections are welcomed, just message me on here or email me and I will try and get back to you as soon as I can. I will post at buyer's expense, so if you are located elsewhere and if you are interested, please contact me for a quote on freight. Images are located for all the parts here: http://www.sau.com.au/forums/gallery/album/5783-classifieds-images/ Thank you. BCNR33 GTR Skyline RB26DETT Camshaft/Timing Covers One of the camshaft covers has been damaged with a part of it snapped off. $150 FJ20 Cylinder Head with front cover/oil pump Bare FJ20 cylinder head Front Cover with Oil Pump $500 Trust/Greddy Hard Intercooler Pipes http://www.trust-power.com/spec_swf/04cooling/1almi_intake_pipeset.htm Only have two of the pipes out of the set of four. $100 each Greddy T78 33D Turbo http://www.trust-power.com/spec_swf/02turbo/Turbo%20Chargers.htm Split pulse design, rated at 720hp Removed due to going to a twin turbo setup $1500 Greddy Type R Wastegate http://www.trust-power.com/02turbo/waste_gate_valve.html http://www.trust-power.com/spec_swf/02turbo/GReddy%20%20Waste%20Gate%20%20Valve.htm Removed due to going to a twin turbo setup $500 Greddy Type R Split Pulse High Mount Exhaust Manifold http://www.trust-power.com/02turbo/sus_turboex_manifold.html http://www.trust-power.com/spec_swf/02turbo/Sus.Turbo%20Ex.%20Manifold.htm Stainless Steel Split pulse design. Removed due to going to a twin turbo setup $1000 Greddy Heat Shield http://www.trust-power.com/02turbo/heat_insulator.html Removed due to going to a twin turbo setup $50 R33 GTR Dash Cluster Reason for removal was swapped out for an aftermarket cluster. Has 26,000km on Odometer. $300 R33 GTR Fuel Pump Controller $50 R33 GTR YAW Rate Sensor $100 R33 GTR RB26DETT Alternator $100 BCNR33 GTR Skyline N1 Centre Triple Gauge Cluster R33 GTR N1 centre triple gauge cluster Worked perfectly before being removed from the vehicle $100 Nissan Skyline GTR RB26DETT Carbon Fibre Timing Belt Cover Unknown Brand I impulse bought it when I was in Japan. $50 Nismo Skyline BCNR33 Series 3 Front under Diffuser http://www.nismo.co.jp/products/catalogue_2014/#page=265 Genuine Nismo S-Tune aero body kit front under bumper spoiler for the Skyline BCNR33 R33 GTR Nismo S-Tune front bumper. Paid around $1000 and then realized it wouldn’t fit! $500 Nissan Skyline BCNR33 GTR N1 RB26DETT Air Box and Snorkel Nissan Skyline BCNR33 GTR N1 Air Box and Snorkel K&N Air Filter $250 RB26DETT Air Flow Meters These were working fine before being removed from the vehicle, one is genuine and one looks aftermarket. $100 for the pair Trust/Greddy 3.7” “Power Extreme” Ceramic Coated Stainless Steel Exhaust with Custom Front/Dump Pipe Hardly used, was only pulled off due to going back to a twin turbo setup on the car. Custom made dump/front pipe to suit 4 Bolt turbo exhaust flange. No catalytic converter. $600 KSP Racing Equipment / Attain Carbon Kevlar Rear Bumper Cover to suit Nissan Skyline R33 GTST or GTR http://www.ksp-eng.co.jp/ATTAIN/exterior/36.html Brand New still in box KSP/Attain Brand Carbon Kevlar $150 Rasty FRP Boot for Skyline R33 GTR/GTS-T http://www.rasty.tv/pro/trunk.html Flat Truck Style painted in QM1 White Some Cracks in the paint where the wing was mounted. Very light $450 R33 GTR Front Lower Arms Stock R33 GTR Front lower arms with ball joints. $150 for the pair Nismo Clear Indicators Brand New Still in Box. $80 R33 GTR R200 Competition Diff Brand New Cusco 2 way Center Brand New Crown Well and Pinion Trust/Greddy Extended High Capacity Diff Cover http://www.trust-power.com/16power_train/diff_cover.html http://www.trust-power.com/spec_swf/05engine/DiffCover_Up_Grade_Kit.htm Diff Cover has also been modified to clear a close fitting exhaust 4.11 Ratio $2000 R32 GTR Dash Speedo Reason for removal was only due to being swapped out for an aftermarket cluster. 52,000km on Odometer. $250 R32 GTR Factory Suspension Inserts and springs. They were removed while they were still in good working cond. $400 R33 GTR ABS Unit Removed from the car only due to installing a pedal box set up. $250 R33 GTR Washer Bottle and Motors Very good condition. $50 R33 GTR RB26DETT Cylinder Head Complete cylinder head with coil packs. Was running perfectly and was only pulled off the engine with the intent to build the bottom end, never happened. $1250 RB26DETT Ind. Throttle Bodies and Plenum. Was running perfectly and was only pulled off the engine with the intent to build the bottom end, never happened. $400 RB26 Starter Motor Was working perfectly and was only pulled off the engine. $100 R33 GTR Sump and Factory Front Diff Was running perfectly and was only pulled off the engine with the intent to build the bottom end, never happened. $300

I have sold my GTR so no longer need the parts/spares. All parts are located in Brisbane south side, and inspections are welcomed, just message me on here or email me and I will try and get back to you as soon as I can. I will post at buyer's expense, so if you are located elsewhere and if you are interested, please contact me for a quote on freight. Images are located for all the parts here: http://www.sau.com.au/forums/gallery/album/5783-classifieds-images/ Thank you. BCNR33 GTR Skyline RB26DETT Camshaft/Timing Covers One of the camshaft covers has been damaged with a part of it snapped off. $150 FJ20 Cylinder Head with front cover/oil pump Bare FJ20 cylinder head Front Cover with Oil Pump $500 Trust/Greddy Hard Intercooler Pipes http://www.trust-power.com/spec_swf/04cooling/1almi_intake_pipeset.htm Only have two of the pipes out of the set of four. $100 each Greddy T78 33D Turbo http://www.trust-power.com/spec_swf/02turbo/Turbo%20Chargers.htm Split pulse design, rated at 720hp Removed due to going to a twin turbo setup $1500 Greddy Type R Wastegate http://www.trust-power.com/02turbo/waste_gate_valve.html http://www.trust-power.com/spec_swf/02turbo/GReddy%20%20Waste%20Gate%20%20Valve.htm Removed due to going to a twin turbo setup $500 Greddy Type R Split Pulse High Mount Exhaust Manifold http://www.trust-power.com/02turbo/sus_turboex_manifold.html http://www.trust-power.com/spec_swf/02turbo/Sus.Turbo%20Ex.%20Manifold.htm Stainless Steel Split pulse design. Removed due to going to a twin turbo setup $1000 Greddy Heat Shield http://www.trust-power.com/02turbo/heat_insulator.html Removed due to going to a twin turbo setup $50 R33 GTR Dash Cluster Reason for removal was swapped out for an aftermarket cluster. Has 26,000km on Odometer. $300 R33 GTR Fuel Pump Controller $50 R33 GTR YAW Rate Sensor $100 R33 GTR RB26DETT Alternator $100 BCNR33 GTR Skyline N1 Centre Triple Gauge Cluster R33 GTR N1 centre triple gauge cluster Worked perfectly before being removed from the vehicle $100 Nissan Skyline GTR RB26DETT Carbon Fibre Timing Belt Cover Unknown Brand I impulse bought it when I was in Japan. $50 Nismo Skyline BCNR33 Series 3 Front under Diffuser http://www.nismo.co.jp/products/catalogue_2014/#page=265 Genuine Nismo S-Tune aero body kit front under bumper spoiler for the Skyline BCNR33 R33 GTR Nismo S-Tune front bumper. Paid around $1000 and then realized it wouldn’t fit! $500 Nissan Skyline BCNR33 GTR N1 RB26DETT Air Box and Snorkel Nissan Skyline BCNR33 GTR N1 Air Box and Snorkel K&N Air Filter $250 RB26DETT Air Flow Meters These were working fine before being removed from the vehicle, one is genuine and one looks aftermarket. $100 for the pair Trust/Greddy 3.7” “Power Extreme” Ceramic Coated Stainless Steel Exhaust with Custom Front/Dump Pipe Hardly used, was only pulled off due to going back to a twin turbo setup on the car. Custom made dump/front pipe to suit 4 Bolt turbo exhaust flange. No catalytic converter. $600 KSP Racing Equipment / Attain Carbon Kevlar Rear Bumper Cover to suit Nissan Skyline R33 GTST or GTR http://www.ksp-eng.co.jp/ATTAIN/exterior/36.html Brand New still in box KSP/Attain Brand Carbon Kevlar $150 Rasty FRP Boot for Skyline R33 GTR/GTS-T http://www.rasty.tv/pro/trunk.html Flat Truck Style painted in QM1 White Some Cracks in the paint where the wing was mounted. Very light $450 R33 GTR Front Lower Arms Stock R33 GTR Front lower arms with ball joints. $150 for the pair Nismo Clear Indicators Brand New Still in Box. $80 R33 GTR R200 Competition Diff Brand New Cusco 2 way Center Brand New Crown Well and Pinion Trust/Greddy Extended High Capacity Diff Cover http://www.trust-power.com/16power_train/diff_cover.html http://www.trust-power.com/spec_swf/05engine/DiffCover_Up_Grade_Kit.htm Diff Cover has also been modified to clear a close fitting exhaust 4.11 Ratio $2000 R32 GTR Dash Speedo Reason for removal was only due to being swapped out for an aftermarket cluster. 52,000km on Odometer. $250 R32 GTR Factory Suspension Inserts and springs. They were removed while they were still in good working cond. $400 R33 GTR ABS Unit Removed from the car only due to installing a pedal box set up. $250 R33 GTR Washer Bottle and Motors Very good condition. $50 R33 GTR RB26DETT Cylinder Head Complete cylinder head with coil packs. Was running perfectly and was only pulled off the engine with the intent to build the bottom end, never happened. $1250 RB26DETT Ind. Throttle Bodies and Plenum. Was running perfectly and was only pulled off the engine with the intent to build the bottom end, never happened. $400 RB26 Starter Motor Was working perfectly and was only pulled off the engine. $100 R33 GTR Sump and Factory Front Diff Was running perfectly and was only pulled off the engine with the intent to build the bottom end, never happened. $300

Cusco Brake Cylinder Stopper Improves brake pedal feel and responsiveness Suits R32 - GTS/GTR Vic Melb - $90

Cusco BCS R34 GTT (maybe R33 GTS-T?) I have for sale a Cusco BCS that I pulled from my R34 GTT, after I fitted a Nismo strut brace with integrated BCS. The guy I bought it from several years ago said he used to run it on his R33 GTS-T - so as far as I'm aware, it should fit R33 GTS-T as well. The item is located in Adelaide, but I'm happy to post at buyers expense. I'm looking for $50, which I think is pretty reasonable.

After thinking over and over again and due to personal and unforeseen circumstances - it will be wiser for me to let my GTR go if the offer is fair - looking at $33k negotiable. No time wasters please... Ad is only posted on SAU and nowhere else... No expense spared on this GTR - buy give her a remap and be happy driving her... Very reluctant but you gotta do what you gotta do... If she doesn't sell before things pick up - then i guess she was meant to be mine.. Car is in very good condition - Year 89 - Chassis is Accident Free - NSW Rego: THE.32R - till May 2015 - Gunmetal Grey - has 155k km on the clock - but i do not know the mileage of the engine - it is running well - car is currently at JLM putting together the final touches and putting the Motor back in... Text me at - zero four three one six two one seven two six RB26DETT :- CP Pistons Eagle Rods HKS cams Springs/Retainers HKS Downpipe Full custom tucked 3.5" exhaust and high flow cat made by Fabulous Fabrications (beautiful work) along with custom Hot/Cold cooler pipe. Intercooler Splitfire Coil Packs with New Harness and extra Grounding Haltech Platinum Pro ECU Bilstein (Yellow) /Eibach strut/spring combo - No leaks and no knocks Ikeya Formula front and rear upper control arms. Front and Rear Apexi Dry Carbon Strut Bars Cusco Swaybars Front and Rear Cusco 1.5w rear diff, fully rebuilt and new diff bushing installed with newer (and slightly larger/stronger) R33 half shafts Diff oils all changed - front and rear less than 5k km Gearbox - Redline Anti Shock Gearbox Oil (Smurf Blood) - less than 10k km OS Giken Twin Plate Clutch and Flywheel HICAS delete Nismo LMGT4's with 265/40/18 Federal RSR all round - less than 1000km Nismo Wheel Nuts Apexi AVCR Nardi Deep Corn Nismo Gearknob Full 3M Tint HID Headlights C's Short Shifter Parts just installed and travelled - 0 km - being put together and putting the Motor back - 100k km service with extras Brand New - Garrett -5's Brand New - Cometic Exhaust Gasket Brand New - Nismo Mounts - Engine Left, Right and Gearbox Brand New - Nismo Clutch Slave Brand New - HEL Braided Clutch Hose Brand New - Nismo Thermostat Brand New - Heater Hoses and Radiator Hoses - Silicone Brand New - Gates Racing Timing Belt, NSK Bearings and Cam Seals Brand New - Water Pump

Selling some stuff off my 33 as Im upgrading. R33 M-Spec Aero, Front bar with indicators, Sideskirts and Rear pods, Painted in factory KH3 super black. Front bar is uncut, but vents have been shaved inside to fit intercooler. Also have factory mesh inserts for bar. - $500 ono Cusco Drag Links - Removing as I'm going to non-HICAS subframe so require toe rods. These will be a complete arm including rods ends. - $250 ono (Will take pic of actual rods when I jack the car up) JDI Front knuckles. Best in the business. Only Selling to use matching F+R knuckles. Knuckles also have 10mm longer Nismo Studs. Also comes with Ikeya Formula adjust tie rods, and KTS bump steer adjustable tie rod ends, to allow for greater movement and the extra length the knuckles require. Wont seperate this kit, all 3 parts are needed together. $500. Pro flow Polished billet fuel rail with injector adapters - Bought black fuel rail instead so not needed - $50 KTS Cradle Collars, Bought these, then bought 33, already had them. Been Sitting on shelf for years - $50 Parts located in modbury, SA. Im away for a week for work, so back next weekend, First come, First Served. Ben - 0419 809 007

Up for sale is a brand new Cusco Carbon Strut Bar for 32 including GTR. I have purchased a titanium Mine's bar now so this Cusco is not required anymore. Brand new in cusco plastic bag and never test fitted, comes with Cusco sticker and tag. Price: $300 firm, no deals. Pickup: 3020 Victoria

Hi Guys, I have for sale a used late model R32 GTR R200 4.11 ratio rear diff with a Cusco 2 way mechanical LSD centre. The centre is to suit 31 spline half shafts, but the diff does not come with them. The lsd, gears and bearings look to be in really good condition. Will also come with the abs sensors. What you see is what you get. Located just south of Wollongong NSW. Would prefer pickup as you all know they are heavy, but can ship at your expense. $1600 plus postage.

FOR SALE LIST Please text 0431143031 with any questions or for further photos CUSCO 6 point bolt in roll car suit non sunroof S13, only owner in great condition $750 Microtech LT12S Suit RB Comes with S1 RB25 engine loom and hand controller $600 RB PULL TYPE CLUTCH EXCEDY Heavy Duty pressure plate 5PUK NPC Sprung center clutch used for a handful of track days $400 Genuine 53mm R32 RB KOYO Radiator, great condition comes with r32 GTR fan shroud used for a handful of track daysv $350 Genuine 37mm 28 Row PWR Oil cooler Comes with lines and sandwich plate $250 GReddy Style copy intercooler W 66mm H 300mm L 640mm at top 780mm from inlet to outlet $200 Surge tank set up With 2 year old genuine bosch 044 fuel pump (working when removed from car) $150 Set of 440cc RB26 top feed injectors (Rail not included) $150 Genuine Tomei fuel pressure regulator Comes with gauge (no lines) Used for a handful of track days $80 Catch Can with lines and filter $50 MONZA 4 Point Harness $40 Speed Meter mechanical oil pressure gauge $20 SAAS Water Temp Gauge Comes with gauge, neck, sender and hose from an RB25 top rad hose $40

1 x Nismo and 1 x Cusco Front strut braces Suit R32 GTR Nismo strut brace has the BMCS and is oval, polished. $200 Cusco strut brace is round - $100 Pics up this evening Pm me if interested.

Parting out an accident damaged 1995 33 gtr with some aftermarket parts. No engine, brakes or front seats. Front end damage so no front body panels. Parts are located in Ipswich qld and I can be contacted via ph. 0413863207 or pm on this forum. Pickup is available and payment is by cash or postal money order. I do NOT do bank transfer or paypal so please dont ask. Condition of parts is as described. Pics. Aragosta coilovers. these are top shelf coilovers, condition is very good with just cosmetic marks from road blast. No leaks or knocks......$1750.00 33gtr gearbox complete with shifter and cross member. Good working condition...$650 Nismo white face dash cluster and triple centre guages, dash cluster is mint with low kays, centre guage are in excellent condition with just a broken corner on a mounting tab. has zero effect on the guage and can not be seen when installed. $650.00 the pair Genuine C's short shifter with heavy throw shift knob, excellent condition...$175.00 Walbro in tank fuel pump wired and ready to clip straight in, perfect condition...$150.00 Genuine Nismo clear indicators with bulbs. perfect condition....$40.00 ther pair Whiteline front sway bar with adjustable links in excellent condition...$200.00 Genuine nissan gtr rear strut brace in excellent condition with mounting brackets..$100.00 Nismo brake lines for gtr, front and rear in very good condition...$150.00 HKS priest stainless exhaust with cat and will throw in front pipes, system is in great condition with just road wear $450.00 Genuine 33 gtr rear wing with carbon end caps. very good condition, paint is not factory..$350.00 Genuine gtr 2 piece side skirts in very good condition, a few scrapes along the bottom but no damage..$150.00 GTR front drive shaft in good coondition...$100.00 Genuine 33 gtr rear sway bar, good upb grade for 33 gtst..$50.00 Dual A pillar pod mount..$50.00 steering column surround..$25.00 Passenger kick panel...$15.00 GTR bovs on genuine gtr pipe...125.00 BM 57 33gtr brake master cylinder..$75.00 33gtr clutch slabe..$50.00 33 gtr power steering reservoir..$50.00 33 gtr ABS unit..$250.00 33 gtr injector resistor pack,,$75.00 33GTR buar raisers...$100.00 33 GTR bonnet hinges..$50.00 Drivers side window switches (2) ..$100.00 each Custom washer bottle catch can combo in polished alloy..$125.00 33 GTR door cards front and rear really good condition with one small blemish on passenger door (see pic)..$150.00 Front passenger guard with a couple of very small dents, easily repairable..$75.00 GTR sump with Cusco 1.5 way diff. Diff is near new, Sump has a hairline crack but will be repaired prior to sale..$650.00 33gtr power steering Wrack in very good condition...$100.00 Complete 33 GTR kaframe with Vspec diff, all arms knuckles and handbrakes. $650.00 GTR centre console cup holder with GTR badge..$25.00 AS new Jim berry full monty clutch and pressure plate. This clutch has done less than 2 hours work and all machine marks are still visible, Would definitely suit new buyer..$800.00 Other items without pics..full set of front and rear prince mats in very good nick...$100.00 Attessa pump..$200.00 Genuine facory rear bar in excellent condition..$150.00 Larger items are pickup, Most items I will post at buyers expense. Should you require any other info please contact me.