Search the Community

So I am a proud owner of a 1990 Nissan R32 GTS4T 4 door RB20DET Auto just under 115,000kms and it has had the 100,000km service completed only couple of months ago (love manual but I needed a 4 door and this was the only one available that was also Turbo, the auto in this config is better than the manual imo as no loss of boost going through gears but sucks at take off but I can get it to drift, though to continue to link up drifts really need to power on and swing the car side to side to keep it loose and shift between 1st and second and ride that boost, really driving the car hard to drift a 4wd and would benefit from an increase in PSI). It has been looked over by the RWC mechanic and Pedders, somethings were found by both but Pedders found a few more. They really are the suspension specialists. So I need the following parts to complete RWC and just to bring the car to a good mechanically sound level. The links are just what I have found on ebay and am open to advise and other products. Front upper control arms with new bushes fitted was considering a pair of these http://cgi.ebay.com....#ht_3816wt_1163 I have been quoted $150 for a reconditioned pair of stock ones. These are the dimensions, are they suitable for the GTS4T? I thought $160 for pair shipping included wasn't bad. Don't want to pull off stock ones to check dimensions if I don't have too as I still need the car to get around in. Inner and Outer CV boots are worn and the grease is all gone and the joints have been damaged so are clicking I have been advise to change the complete CV shaft left and right. So both left and right front CV shafts, joints and boots required. Are these what I need? Rear tie rod end bushes (They look like a knuckle setup, they are the ones out at the wheel you can see it from looking under and behind the wheels) I will take some pictures and post. All discs need machining due to being worn, rusty & glazed but I have been told these are lipped and cannot be machined so looking to upgrade to a slotted vented pair thinking rears can stay stock style but need new discs. Front http://www.ebay.com....9#ht_632wt_1163 Rear http://www.ebay.com....9#ht_500wt_1180 not sure if slotted really needed for rears. Left hand front shock very firm near seized both front shockers advised to be changed. What is a good value for money pair? Left hand top shock mount requires replacing due to shock failure it has been taking the brunt of the absorption, should I change left and right or just the left damaged one is ok? If just left I am looking for stock one if both I saw these http://www.ebay.com....a#ht_500wt_1180 Front D Bushes worn need replacement (sway bar mount bushes) is this a set that will fix this? http://www.ebay.com....4#ht_1679wt_960 Light play in steering rack it PASSED for Pedders and RWC mechanic but they said should be looked at in the next 6 months, I think it is fine but wondering what a reco one will cost and is a 2WD rack different to a 4WD rack? Radiator hoses are hard and crunchy and need to be replaced. Found this http://www.ebay.com....#ht_1401wt_1163 are they correct ones. I need a Left dash heater air vent The CENTER GEAR CONSOLE SURROUND is cracked,pitted,melted by cigarette burn and chipped so was looking at this, seems pricey though, but the ad mentions more durable than stock one. http://www.ebay.com....#ht_1514wt_1163 Hoses behind radiator, in front of motor (oil cooler pipes) need new clamps. Hoses are slightly perished but not the cause of leaking it is the clamps that are at fault for leaking but they recommend changing hoses and clamps at same time and advised only need less than 1.5mtr of hosing to do, what is the dimension of the pipe that is required? I can pick up a length from super cheap unless there is a highly recommended alternative product. Rear under side has a little surface rust and they recommend treating it with fish oil anyone concur? Found this, is it needed? http://www.ebay.com....#ht_2406wt_1163 So supply of parts if any are for sale would be awesome but peoples advice both on parts choice, compatibility and pricing would be appreciated.