Search the Community
Showing results for tags 'tail'.
Found 7 results
-
Hey so up for sale are the V35 Series 1 Sedan Tail Lights with Trunk Portion $320 ONO These wheels on my car are on sale as well, here are some pics They are the HR Racing HR-472 Dull Black w/ Red lip around the wheels in 19x8 around 35 offset all round with tires, still has some good amount of tread left. Gutter rashes here and there $650 ONO -
hey everybody. i would like to swap a maroon left rear tail light assembly for a chrystal white left rear tail light assembly. im happy to pay for postage so you are not out of pocket. im in n.s.w blacktown. happy to travel reasonable distance. if you want ill even include the old white cracked tail light for free. im prety shure the maroon light its in good condition with no cracks or marks but ill make 100% shure if someone is keen on doing this it would be greatly appreciated. -
G'day guys, Just throwing it out there if anyone would light customized headlights? I can split, clean the lenses inside and out. Polished and paint the surrounds any colour you want, install LED's etc. And can supply most suspension bushes and/or fit for wa guys as well (: compression bushes, control/camber arm bushes. (: lemme know if there's any interest. Have done a couple with/ for friends so though I'd see if its something people would want. cheers guys kohbz
-
1 Tein RS Circuit Master ( rebuilt by racepace) Set of race pace tein rs circuit master coil overs Possibly the best upgrade I have done to my car( on the exact same car shaved 2 seconds off on a 60 second lap out of the box) Approximately 2000km old Tarmac rally spec so perfect on the road and bumpy tracks Best money you will ever spend Suit r33 and r34 $2700 R33 gtr Ap endurance setup R33 gtr Ap endurance setup Front 365/355 6 piston Ap racing endurance kit 36 mm full floating rotors Endurance calipers 35mm pad each side Race brakes custom lines Spare set of rotors and hats 4 sets of front pads Rear 330 4 piston endurance calipers Full floating Custom lines Spare rotors 3 sets of pads $5000 with brembos exchange can also include a full Ap racing balance bar setup and hydro handbrake setup to match for extra dollars This is a serious setup that takes a lap or two to warm up then it rips you face off till you get bored or run out of types and fuel 4 Os giken 5 speed in s3 gtr casing Billet input Os tripple plate Push pull converter Was assembled by award diff 6k plus a stock box my way Box and clutch have done 1-2 k In car and can be tested No pics as its a box and In the car all shit located in theblue mountains sydney if you want something ive me a call come over inspect and buy pete 0448468884
-
Needed: Aus Spec R32 Tail lights Hi Everyone first post on this forum! I am looking for a pair of Aus Spec tail lights for my GTR. Maybe you have a pair or know someone with a pair of them with the amber turn signal. Must be in great condition. Thanks!
-
Hello world! Looking to make a quick tutorial on how to change out your tail lights in the s15 for a set of aftermarket lights. I have attached a video on the process you can view, and I have written the process underneath! Please let me know if you have any questions or feedback. Steps to swapping your tail lights. You will need to first start off by finding a nice set of aftermarket tail lights you would like to install into the car. I have chosen a set of Yashio Full LED tail lights (Apart from the reverse light) There are other nice sets out there too such as the dmax type and sex spec types. I prefer the Yashio ones. Tools you will need: - Phillips head screwdriver - Flat head Screw driver - Socket set (a spanner would work too if you don't have any sockets) - Mine was an 8mm socket, but I believe my nuts are incorrect so yours might be 10mm - You may also need some side cutters for cable ties if you have any Once you have said set of tail lights and tools ready, we will start off by removing the old tail lights. If you open your boot, you will find the where the boot closes, there is a grey strip which runs from the left to the right of the rear of the boot, pictured below. You will need to gently unscrew the Phillips head screws (circled in green), and you will find they cannot be unscrewed any more, just pop them out. You will then have some clips you need to remove, I have circled the points which need to be removed in red, just pop a flat head screwdriver in the tabs and pop them out. There are 2 of these on each side. The grey peace should now lift up and out of the way! Once you have the grey piece out, you will need to remove the 4 nuts holding the old lights in. there are 2 located next to the grommet, and then 2 moving out towards the middle, one is closer than the other. I have attached another image below of roughly where the nuts are located if you are looking down on it, you will see when you are working. you will also need to unplug the white connector going to your lights, I suggest you get a small Flathead and use it to push down on the release latch on the connector if yours are old like mine they can become a pain release. The light should now slide out of its place, make sure you are holding it from the front so you do not drop it Once the light is out, simply reverse the process. If you are installing the Yashio Tail lights like me, you will have a small black box you need to stick to the inside of your boot, and there will be a little plug you need to plug into that too, coming off the lights, simply unplug it to get the cable through the boot and back through the grommet, and then plug it back in once the cables back in the boot (I am not 100% sure what this box is for, initially, I thought it was just to decrease the current and voltage so that it does not fry the lights, but cannot confirm if this is it's only use. It is quite large and would expect such a device to be much smaller. If you know what this is for I would be curious to know Please let me know) Hopefully, you followed through with the tutorial and the new lights look great! Keen to see the results so post up some photos if you followed my tutorial, or even if you just came across it and you have your own lights If you have anything you think I missed and you would like to add, please let me know, I can add it at any time
-
Chasing an R34 GTR Tailshaft/Prop Shaft and Front Prop Shaft. Ready to buy, please PM me or reply to this thread.
