Jump to content
SAU Community

Pbr Slave Cylinder Part Number?

predator

By predator,
in General Maintenance

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

Does anybody have the box, etc lying around and know the part number for the RB20DET slave cylinder?

I went to repco today, and they were not sure of the exact one, even though they had some close guesses. Anybody know for sure?

I believe its PBR brand.

Link to comment
https://www.sau.com.au/forums/topic/100459-pbr-slave-cylinder-part-number/
Share on other sites
Cubes Grand Master

Cubes

Posted
Posted (edited)

PBR don't do one for the R32 as far as I'm aware..

Its another brand..

I replaced mine, slave w around $40, the master cyl was $75 or there abouts. I will try and find the pics I took of the part number(s).

I think I listed the part numbers in an SA thread I made a while back.

Edited by Cubes
predator Grand Master

predator

Posted
  • Author
Posted

Called the distributor (IBS not PBR), and they pointed me in the direction of a stockist in my area.

IBS-JB4215 was the part number which was compatible with my old one..

http://www.indbrake.com.au/ -- call for distributors in your state.

Cost was $33 ;) Can't beat that for a brand new unit.

You will need to use your existing 'pin' out of the old one, or you should be able to easily find something else suitable.

Cubes Grand Master

Cubes

Posted
Posted (edited)

Remove the center box while your replacing the master cylinder.

Bend the line from the master cyl back on its self so it connects directly to the rubber slave cyl line.

I found pedal feel to be much better with a ceramic clutch, I am now able to slip it and have more control over fine movements.

Prior it felt I was a blind man. :P

Bleeding is also much easier.

Edited by Cubes
  • 11 months later...
eXc Mentor

eXc

Posted
Posted
Called the distributor (IBS not PBR), and they pointed me in the direction of a stockist in my area.

IBS-JB4215 was the part number which was compatible with my old one..

http://www.indbrake.com.au/ -- call for distributors in your state.

Cost was $33 :/ Can't beat that for a brand new unit.

You will need to use your existing 'pin' out of the old one, or you should be able to easily find something else suitable.

Just thought I'd confirm this is the correct part number, I got one today. R32 GTST Slave cylinder...

95SKY Community Regular

95SKY

Posted
Posted
Called the distributor (IBS not PBR), and they pointed me in the direction of a stockist in my area.

IBS-JB4215 was the part number which was compatible with my old one..

http://www.indbrake.com.au/ -- call for distributors in your state.

Cost was $33 :( Can't beat that for a brand new unit.

You will need to use your existing 'pin' out of the old one, or you should be able to easily find something else suitable.

Maybe try JB4215 for PBR?? Just a idea??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • EndZee
      Weird compression after rebuild

      By EndZee · Posted

      But if I smoke test 5th cylinder it’s all ok, no leaks  when I try with 2nd it’s leaking exhaust and intake, it doesn’t come from oil dip stick.    so maybe when car was running poorly, rich or sth. Spark plugs were black and covered in charcoal or sth lookalike. could potential contamination make valves not seal properly? is there also a possibility that rb’s don’t have equal performing cooling passages  meaning back of the engine will be hotter than front. Can this cause improper wear if engine was running under load for short time? Or carbon build up could just burnt from 4-6 and is still on 1-3?   I out of my head like really. Timing is as manual crank-exhaust 47, exhaust-intake 38 at this point I thinking about give it a try and make another 500-1000km and check if anything change, if not I will most likely disassemble engine head /or whole engine and send it back to rebuild. It’s killing me     
    • wrxhoon
      WTB R33 GTST Catch Can 2L or Bigger

      By wrxhoon · Posted

      Thanks Duncan, I don't have a GTR these days mate. Gone soft..
    • dbm7
      Weird compression after rebuild

      By dbm7 · Posted

      Yeah. air pressure leakdown test is where I would be headed next here, using one's ears to determine whether it's the valves or bores/rings leaking...
    • GTSBoy
      Weird compression after rebuild

      By GTSBoy · Posted

      More likely you didn't bed the rings in correctly and have glazed the bores. Running with misfires on a fresh build is somewhat of a no-no. Surely no-one "smoke tests" the combustion chamber? That's what a leakdown test is for. Smoke testing is, um, a bit of a wank at best, and only really useful for external pipework.  
    • GTSBoy
      Attesa pump mount options / ideas? R32 gtr style.

      By GTSBoy · Posted

      Well, obviously that kit is not a relocation kit or anything other than just the original isolators and the like. I would suggest that it should be a matter of just bending up some flat bar to build a mount over the top of some other diff, with the flat bar held to the back of the diff by the rear hat bolts. A little welding, a little thinking about how to secure the front of this structure, maybe some different hoses in case you can't get it in just the right place.
×
×
  • Create New...