Jump to content
SAU Community

Eoi: Low Profile Jack And Jack Stands


NiCk-180
 Share

Recommended Posts

I assume by jack stands you mean axle stands? Are they the cast or tubular variety? In regards to the Australian Standards issue, can someone clarrify if there is a distinction between A.S. approved and "complies with", because with many regulations there is a huge difference. Usually "complies with" implies that the manufacturer warrants the product meets the stated specification, whereas approved means its been submitted for inspection and documentation is issued to show the item has been found to meet the specification.

Just to add a bit more. From an Australian Standards policy document:

All Australian Standards are, in themselves, voluntary; however, between one-third and one-half of all Standards are referenced under State or Commonwealth legislation. A number of Australian Standards relating to the safety of consumer products or information about consumer products are referenced in Mandatory Standards under the Trade Practices Act (TPA).

The TPA is a Commonwealth law and controls the activities of corporations. State and Territory Governments also have controls on consumer products under their Fair Trading Acts which extend to the activities of sole traders and partnerships. In recent years, there has been considerable progress in harmonizing Commonwealth and State controls on the supply of consumer products.

The Mandatory Standards under the TPA control the supply of goods, as opposed to the usage of goods. For instance, State traffic laws require that cyclists must wear an approved bicycle helmet; however, the Mandatory Standard under the TPA ensures that only bicycle helmets complying with AS/NZS 2063 can legally be sold. If the usage of a product is controlled, but the supply is not, there is a possibility of consumers purchasing products in good faith that cannot be legally used.

Sorry for the hassle, but you can understand my concern given the possibility of serious injury should equipment like a jack fail. I am genuinely and seriously interested in purchasing; I'm not just tyre kicking for the hell of it.

Link to comment
Share on other sites

I assume by jack stands you mean axle stands?  Are they the cast or tubular variety?  In regards to the Australian Standards issue, can someone clarrify if there is a distinction between A.S. approved and "complies with", because with many regulations there is a huge difference.  Usually "complies with" implies that the manufacturer warrants the product meets the stated specification, whereas approved means its been submitted for inspection and documentation is issued to show the item has been found to meet the specification.

Just to add a bit more.  From an Australian Standards policy document:

Sorry for the hassle, but you can understand my concern given the possibility of serious injury should equipment like a jack fail.  I am genuinely and seriously interested in purchasing; I'm not just tyre kicking for the hell of it.

Yes i do mean axle stands. They are cast.

The jack is approved by the appropriate authorities.

*This is not an el'cheapo product*

just so you know frieght to NSW is aprox $32

If you have any other questions feel free to ask

cheers

Nick

Link to comment
Share on other sites

Nick,

Thanks for that. I managed to drag up the appropriate government document anyway: http://www.accc.gov.au/content/index.phtml/itemId/663755

Although the standard itself mandatory, compliance with the standard does not involve any submission and certification (i.e. the manufacturer certifies the product). So everything is hunky dory.

Soon as I get a little cash (hurry up ATO!), I'll shoot you a PM.

Link to comment
Share on other sites

Nick,

Thanks for that.  I managed to drag up the appropriate government document anyway: http://www.accc.gov.au/content/index.phtml/itemId/663755

Although the standard itself mandatory, compliance with the standard does not involve any submission and certification (i.e. the manufacturer certifies the product).  So everything is hunky dory.

Soon as I get a little cash (hurry up ATO!), I'll shoot you a PM.

no worries dude,

just spoke to the supplier is wiling to prove he has the apropriate certification

Link to comment
Share on other sites

Same here.. I just got mine delivered as said..

Top stuff, the courier dude was good too, helped me take the jacks all the way to the back of the apartments and put it in my garage.. I didnt have to loose a sweat.

As for Nick, great stuff too.. Easy payment in bank account on Friday and I got my goods today (Tuesday).

Cheers!

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
 Share



  • Similar Content

  • Latest Posts

    • 100% this, no point delivering a steam oven when the client just wanted a toaster 
    • The best part of my setup is, we only have two sites. Our head office where I'd put every thing has plenty of internet capacity. We're on a 200/200 dedicated fibre. Even better, there's only like 6 people in the office at most, and the other office has 2 people in it (likely 3 soon). The majority of our work is in a custom piece of software, as it is part of the backend of the system we provide to customers. For our arrangement, on prem would be wayyyyy easier, and a VPN tunnel site to site is easy for me to manage. Scaled at many many sites, or quite a few hundred employees it's starts getting a bit different for all people outside the head office. However, everything in the cloud becomes worse for the people who operated previously at the site that held the servers, as now they're at the mercy of their internet, and not GBPS internal network (f**k the idiots who hook a desktop PC up on WiFi or permanently sit at a desk using a laptop and don't go remotely with it).   It really does come down to the business needs and structure as to what is best. For us, 365 is mainly being moved to for office apps, moving email from Google to Exchange, and setting up "Active directory". Otherwise we have a ticketing system with support that runs on our own cloud system, or the sales process sits in a CRM we pay for. My biggest push back for having most of the shit turned off and saying no when people want new shiney things is "that won't meet our security requirements, or efficiency gains, so all you're requesting is money spend to open us up to security issues, or to make our staff less efficient" Which is funny when one of our core values is "To do more, with less"
    • Think of it as a fancy iFrame with the auth passed through to PowerBI as you're already authenticated logged into Teams   I'm the complete opposite, I hate everything on Prem, it's slow as shit, you need VPNs to get anything happening, then when you want on-prem DBs to talk to say PowerBI you need to install/setup data gateways to essentially VPN back into your SQL instance. I suppose from my perspective, on-prem sucks, but from an infrastructure perspective, your environment is somewhat air gapped to the web via your firewall(s), etc.   The curse of knowledge, the more you know the more you suffer. Farken philosophical shit.
    • Would you mind uploading the pics again in your steps?  It’s not showing up. 
    • Wherever you ask them to. I had one added to the crossover pipe near the BOV as well as the hot and cold sides of the intercooler piping to provide greatest flexibility in measuring temperatures post-turbo. I have the IAT installed in one, and bungs in the other two.  
×
×
  • Create New...