Jump to content
SAU Community

Recommended Posts

The 2835R turbos are probably the limiting factor on the R33 at the moment.They were chosen because on a 3 litre engine with 9.1:1 comp they give strong top end power & also come on boost relatively quickly - making the car very responsive for street use.

Now the car has morphed into a race car(is awesome on the street - but who am I kidding - it's no daily driver) the smallish turbos limit the current setup to around 850-900 hp.

I would like to fit 3037S & remap the motec to suit which should see the output raised to 1000hp without ringing it's neck - but

no-one has put their hand up for the 2835Rs & without selling them I can not upgrade.Larger turbos would increase lag, but on a car that rarely sees less than 7000rpm that would not be an issue.I would like to see the car run a 9.4 as it is - but drag racing is a funny thing. 9.6 might be where it's at, & thats fine.

Slicks would definately be faster.Possibly by 4or 5 tenths, but create other problems.For a start, there are 2 classes for GTRs -

"street drag GTR" running radial tyres (Nittos) or "Pro GTR" running slicks.It is much more than a simple tyre swap.To run slicks you must run 15" rims, which means removing all the GTR

brakes & running smaller non turbo style discs & calipers.Also the suspension has to be totally changed to suit the softer tyres.

another problem is that in Australia(under ANDRA rules) a 4WD is

not allowed to run non radial tyres all round - so unless it's an outlaw meeting at a non-sanctioned event - it wont comply.

The HKS car was exempt at Drag Combat last year as an exhibition car - but they nearly did not let it run as it did not comply with heaps of ANDRA regulations.The shock load through the drivetrain from a 4WD slicks launch can also cause severe breakages.It also means 4 slicks,4 rims, brake changes etc - add that up.Rather than do a bit at a time & slowly get the car into the 9s, I decided to go all out & stretch as far as I could.With the std engine my best was 11.10. Now with new engine my best is 9.66. That's a huge leap in drag racing.With fine tuning & 60' practice we may shave a tenth or two, but the next step into the low 9s could cost anywhere from $20-30,000.00

It's also about the look of the car. As it is it looks like a fairly normal GTR at first glance(I was driving down GJ rd recently & a copper coming the other way didn't even turn to look at it!)

With 15" rims, lexan windows all round,no headlights, & covered with stickers I think it spoils the look of a GTR.People can relate to it if if still looks like a street car.Hope the weather is good for Sat night - looking forward to 9500rpm & playing with my Holinger.

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I mean this in no disrespect to u mate; Are there clear tagged examples/explanations in our SAU forum for example, in my interest, this is how to do R34 Gtt suspension the right way? U guys did so much taking risks with experimentation that deserves recognition and those results helps us morons take the RIGHT path to buy quality / buy once. 🍻
    • Pretty much what you'd expect at that power level. Hypergear turbo, long list of supporting mods, full Haltech catalogue, etc.  I'd say this goes for most drivers, suspension is still a dark art for most people. And it's really hard to convince someone how much better their setup could be...  
    • They are what I will be installing. 640s for me.
    • Hmm... From my experience you get about 0.25° camber change per mm of RUCA length change. So, to correct from -2.5 up to less than -1° (or, more than -1° if you look at the world as a mathematician does) then you'd be making 6-8mm of length change on the RUCA. From a stock length of 308mm, that's 2-2.5% difference in RUCA length. My RUCAs are currently very close to stock length - certainly only 2-3mm different from stock. I had to adjust my tension arms by 6mm to minimise the bump steer. That's 6mm out of 210, which is 2.8%. That's a 2.8% change on those, compared to a <1% change on the RUCAs. So the stock geometry already has worse bump steer than is possible - you can improve it even if you don't change the RUCA length. If you lengthen the RUCAs at all, then you will definitely be adding bump steer. Again, with my car, I recently had an unpleasant amount of bump steer, stemming from a number of things that happened one after another without me having an opportunity to correct for them. I only had to change the tension arm lengths by 1mm to minimise the resulting bump steer. (Granted, I also had to dial out a lot of extra toe-in in the rear, and excessive rear toe-in will make bump steer behaviour worse). Relatively tiny little adjustments having been made - the car is now completely different. Was horrifying how much it wanted to steer from the rear on any significant single wheel bump/dip. And it was even bad on expansion joints on long sweepers on freeway entry/exits, which are notionally hitting both rear wheels at the same time. My point is, the crappy Nissan multilink is quite sensitive to these things (unlike the very nice Toyota suspension!). And I think 99.75% of Skyline owners are blissfully ignorant of what they are driving around on. Sadly, it is a non-trivial exercise to set up to measure and correct bump steer. I am happy to show my rig, which involves nasty chunks of wood bolted to the hub, mirrors, lasers, graph paper targets and other horrors. Just in case anyone wants to see how it is done. I'll just have to set it up to take the photos.
    • What do you have in that bad boy ? Ill go with the 725cc since I'll be going with Nistune ( would definitely like more engine protection but Haltech is too far out of reach at the moment... plus, Ill probably have a pretty safe tune as its a daily, not gonna be chasing peak power 24/7 ahahah ). Are Xspurt a safe choice?  Pete's great. He didnt mention anything about traction arm length so I reckon it may be good. When I get some new wheels/tire later down the road I'll ask him about it and get his opinion on em. I heard from Gary that you've got the bilsteins too, are you running the sway bars too? and what other suspension goodies do you have installed or would recommend?
×
×
  • Create New...